torque SSANGYONG MUSSO 1998 Workshop Manual PDF

M162 ENGINE MECHANICAL 1B1-101
OIL PRESSURE RELIEF VALVE
Preceding Work : Removal of oil pan
1 Screw Plug................................................ 50 Nm
2 Compression Spring
Removal & Installation Procedure
1. Remove the screw plug (1).
Installation Notice
2. Remove the spring (2), guide pin (3) and the piston (4).
3. Installation should follow the removal procedure in the
reverse order.
Notice
Don’t use the seal for the screw plug.3 Guide Pin
4 Piston
Tightening Torque 50 Nm

M162 ENGINE MECHANICAL 1B1-103
OIL DIPSTICK GUIDE TUBE
1 Oil Dipstick Level Gauge
2 Oil Dipstick Guide Tube
Removal & Installation Procedure
1. Pull out the oil dipstick level gauge (1).
2. Remove the bolt (4) in the upper intake manifold and remove
the oil dipstick guide tube.
Installation Notice
3. Install new O-ring to the dipstick guide tube.
4. Installation should follow the removal procedure in the
reverse order.
5. Check for leaks by starting the engine.3 O-ring
4 Bolt (M6 x 12, 1 piece)........................... 9-11 Nm
Tightening Torque 9 - 11 Nm

1B1-106 M162 ENGINE MECHANICAL
OIL GALLERY IN CYLINDER HEAD
Preceding Work : Removal of cylinder head
Removal of camshaft
Removal of tappet
1 Screw Plug................................................ 15 Nm
2 Seal
Cleaning Procedure
1. Remove the screw plug (1) and the seal (2).
Installation Notice
Replace the seal with new one.
2. Clean the oil gallery using the compressed air.
3 Steel Ball (f8mm)
Tightening Torque 15 Nm

M162 ENGINE MECHANICAL 1B1-107
Sealing Procedure
1. Remove the screw plug (1) and the seal.
Installation Notice
2. Remove the steel ball from the oil gallery (4), (5), (6) and
(7) using the round bar (12,
f6 x 700 mm).
4. Enlarge the oil gallery at the rear of the cylinder head to be
diameter 9mm, depth 8mm.
5. Tap in the steel ball (3) from the side to the oil gallery using
the punch (13).
6. Pull out the steel ball (3) using the round bar (12).
7. Enlarge the oil gallery to be diameter 9mm, depth 8mm.
Tightening Torque 15 Nm
3. Remove the plug (8) using the screw driver.

1B2-4 M161 ENGINE MECHANICAL
SPECIAL TOOLS
SPECIAL TOOLS TABLE
000 589 10 99 01
Torque Wrench
112 589 00 72 00
Oil Extractor000 589 72 21 00
Torque Wrench
001 589 66 21 00
Torque Wrench
000 589 01 10 00
Box Wrench Insert124 589 15 21 00
Radiator Cap
Testing Unit
116 589 02 34 00
Screw-Fixed Pin000 589 40 37 00
Hose Clamp

1B2-6 M161 ENGINE MECHANICAL
SPECIAL TOOLS TABLE (Cont’d)
116 589 20 33 00
Sliding Hammer
602 589 00 40 00
Engine Lock103 589 00 33 00
Puller
601 589 03 43 00
Sleeve
001 589 65 09 00
Socket Wrench Insert
001 589 74 21 00
Torque Wrench000 589 04 14 00
Clamping Strap 000 589 88 33 00
Puller

M161 ENGINE MECHANICAL 1B2-7
SPECIAL TOOLS TABLE (Cont’d)
103 589 01 63 00
Rivet Set
103 589 02 09 00
Oil Filter
Socket Wrench102 589 12 15 00
Drift
615 589 01 33 00
Caulking Bolt
102 589 00 15 00
Drift
000 589 51 37 00
Clamping Strap001 589 72 21 00
Torque Wrench 601 589 03 14 00
Sleeve

M161 ENGINE MECHANICAL 1B2-9
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
ENGINE ASSEMBLY
Tools Required
000 589 10 99 01 Torque Wrench
000 589 40 37 00 Hose Clamp
112 589 00 72 00 Oil Extractor

1B2-10 M161 ENGINE MECHANICAL
4. Disconnect the coupling of HFM sensor and remove the air
cleaner cross pipe.
6. Loosen the radiator drain cock and drain the coolant.
Notice
Open the coolant reservoir cap. 5. Remove the air cleaner cover. Remove the mounting bolts
and air cleaner housing and element assembly.
Removal & Installation Procedure
1. Disconnect the negative terminal of battery.
2. Remove the hood.
3. Remove the under cover.
Installation Notice
Tightening Torque 28 - 47 Nm

M161 ENGINE MECHANICAL 1B2-11
10. Remove the upper mounting bolts of radiator and then
remove the radiator.
7. Loosen the cylinder block drain plug and then drain the
coolant completely.
Installation Notice
Tightening Torque 30 Nm
Notice
Replace the seal before installation of the drain plug.
8. Remove the cooling fan shroud.
9. Disconnect the each hose from radiator.