service SSANGYONG MUSSO 1998 Workshop Service Manual

M161 ENGINE MECHANICAL 1B2-109
Service Data Standard
Measurement of Cylinder Bore
1. Clean the cylinder wall.
2. Using a internal diameter gauge, measure the bore size in
axial and transverse direction at three points (1,2,3).
1,2,3 Measuring Points
A . Axial Direction
B. Transverse Direction
a. Location of the No.1 Piston Ring at TDC
b. Location of the Piston BDC
c. Location of the Oil Ring at BDC
Chamfer Angle
Wear Limit in Longitudinal and Transverse Direction
Permissible Deviation of Cylinder Out-of-round
Permissible Deviation of Rectangular Cylinder Height (Except Chamfered Area)
Basic Peak-to-valley Height After Final Honing and Brushing
Chamfer Angle
Honing AngleWhen new
Wear limit0.1 mm
0.007 mm
0.05 mm
0.05 mm
0.003 - 0.006 mm
75°
50° ± 10°
1) The group code letters are carved on the surface of the piston crown and in the mating surface of the crankcase.Type
Standard Size
E20 :
f 89.9
E23 :
f 90.9
1st Repair Size
(Standard Size + 0.25)
2nd Repair Size
(Standard Size + 0.5)Group Code Letter
1)
A
X
B
A
X
B
A
X
BCylinder Bore Size (mm)f 89.900 - f 90.906
f 89.906 - f 89.912
f 89.912 - f 89.918
f 90.150 - f 90.156
f 89.156 - f 90.162
f 90.162 - f 90.168
f 90.400 - f 90.406
f 90.406 - f 90.412
f 90.412 - f 90.418

1B2-110 M161 ENGINE MECHANICAL
CRANKCASE MATING SURFACE
Service Data Standard
Height of the Crankcase “H” (When New)
Minimum Height After Milling
Flatness
Permissible Deviation of Parallelism of the
Upper to Lower Mating Surface
Peak-to-valley HeightCrankcase Upper Mating Surface
Crankcase Lower Mating Surface
Axial Direction
Transverse Direction
Crankcase Upper Mating Surface
Crankcase Lower Mating Surface289.35 - 289.45mm
289.05mm
0.03mm
0.04mm
0.1mm
0.05mm
0.012 - 0.009mm
0.025 - 0.020mm

1B2-112 M161 ENGINE MECHANICAL
CYLINDER HEAD MATING SURFACE
Preceding Work : Removal of valves
Service Data Standard
Notice
Do not exceed 0.4mm for the milling of the mating surface of crankcase and cylinder head.Overall Height of Cylinder Head
Minimum Height After Machining
Flatness
Distance ‘T’
(Between Camshaft Bearing
and Valve Stem)Axial Direction
Transverse Direction
Standard Size
Repair Size135.9 - 136.0 mm
135.5 mm
0.08 mm
0.0 mm
24.21 - 24.75 mm
22.21 - 22.75 mm
23.96 - 24.51 mm
21.96 - 22.51 mm
Intake
Exhaust
Intake
Exhaust

M161 ENGINE MECHANICAL 1B2-113
Measurement of Mating Surface
1. Measure the height (H) of the cylinder head (refer to Service
data standard
).
2. Check the mating surface of the cylinder head.
3. Mill the sharp edge of the combustion chamber.
4. Re-measure the height (H) of the cylinder head.
5. Seal the intake and exhaust valves.
6. Measure the dimension (T) between the camshaft bearing
and the valve system (refer to
Service data standard).
7. Mill the cylinder head valve seat (refer to
Service data
standard
).
Universal Tool
Surface Grinding MachineSceledum, Type RTY
Roaro
Schio/Italy

SECTION 1B3
OM600 ENGINE MECHANICAL
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1B3-2
Fastener Tightening Specifications . . . . . . . . 1B3-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1B3-4
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1B3-4
Maintenance and Repair . . . . . . . . . . . . . 1B3-12
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1B3-12
Engine Assembly . . . . . . . . . . . . . . . . . . . . 1B3-12
Poly V-Belt . . . . . . . . . . . . . . . . . . . . . . . . . 1B3-21
Tensioning Device . . . . . . . . . . . . . . . . . . . . 1B3-23
Poly V-Belt Alignment & Inspection . . . . . . . 1B3-26
Prechamber . . . . . . . . . . . . . . . . . . . . . . . . 1B3-29
Milling of Prechamber Sealing Surface . . . . 1B3-32
TDC (TDC Sensor Bracket) Setting . . . . . . 1B3-35
Cylinder Head . . . . . . . . . . . . . . . . . . . . . . . 1B3-37
Timing Case Cover . . . . . . . . . . . . . . . . . . . 1B3-63
Crankshaft End Cover . . . . . . . . . . . . . . . . 1B3-71
Vibration Damper and Hub . . . . . . . . . . . . . 1B3-74
Crankshaft Front Radial Seal . . . . . . . . . . . 1B3-80
Crankshaft Ball Bearing . . . . . . . . . . . . . . . 1B3-82
Crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . 1B3-83
Flywheel . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B3-93
Machining of Flywheel . . . . . . . . . . . . . . . . 1B3-97
Flywheel Ring Gear . . . . . . . . . . . . . . . . . . 1B3-98
Hydraulic Valve Clearance Compensation
Element Check . . . . . . . . . . . . . . . . . . . . 1B3-101
Valve Tappets . . . . . . . . . . . . . . . . . . . . . . 1B3-103
Valve Spring Check . . . . . . . . . . . . . . . . . 1B3-105
Valve Springs (Cylinder Head Removed) . 1B3-106
TABLE OF CONTENTS
Valve Springs (Cylinder Head Installed) . . 1B3-109
Valve Stem Seals . . . . . . . . . . . . . . . . . . . 1B3-112
Check and Replacement of
Valve Guides . . . . . . . . . . . . . . . . . . . . . 1B3-116
Valve Seat Rings . . . . . . . . . . . . . . . . . . . 1B3-122
Check and Machining of Valves . . . . . . . . 1B3-127
Machining of Valve Seat . . . . . . . . . . . . . . 1B3-132
Camshaft Timing Test . . . . . . . . . . . . . . . . 1B3-137
Camshaft . . . . . . . . . . . . . . . . . . . . . . . . . 1B3-139
Chain Tensioner . . . . . . . . . . . . . . . . . . . . 1B3-145
Timing Chain . . . . . . . . . . . . . . . . . . . . . . . 1B3-147
Tensioning Rail . . . . . . . . . . . . . . . . . . . . . 1B3-151
Cylinder Head Guide Rail . . . . . . . . . . . . . 1B3-152
Timing Case Cover Guide Rail . . . . . . . . . 1B3-156
Crankshaft Sprocket . . . . . . . . . . . . . . . . . 1B3-158
Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B3-163
Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 1B3-169
Oil Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B3-171
Oil Spray Nozzle . . . . . . . . . . . . . . . . . . . . 1B3-174
Oil Pump . . . . . . . . . . . . . . . . . . . . . . . . . . 1B3-175
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . 1B3-177
Cylinder Head Pressure Leakage Test . . . 1B3-177
Facing Cylinder Head Mating Surface . . . . 1B3-178
Replacement of Crankcase Core Plug . . . 1B3-180
Facing Crankcase Contacting Surface . . . 1B3-182
Oil Gallery Steel Ball . . . . . . . . . . . . . . . . . 1B3-183
Cylinder Bore Measurement . . . . . . . . . . . 1B3-187

1B3-12 OM600 ENGINE MECHANICAL
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
ENGINE ASSEMBLY

OM600 ENGINE MECHANICAL 1B3-35
TDC (TDC SENSOR BRACKET) SETTING
Preceding Work : Removal of No.1 cylinder prechamber
1 Measuring Device
2 Dial Gauge
3 Cylinder Head
4 Piston................................................Set at TDC
Tools Service
001 589 32 21 00 Dial Gauge
601 589 07 21 00 Deqth Gauge
667 589 01 21 00 Fixing Device
Notice
lThe TDC sensor bracket must be adjusted in case of
followings.
lWhen replacing the TDC sensor bracket.
lWhen replacing the crankshaft, the hub or the vibration
damper.
lWhen replacing or installing the timing case cover.
lAfter engine overhauling.
*If the cylinder head is removed, the measuring pin of the
dial gauge can be positioned on the piston crown.
This is done by placing the magnetic dial holder on the
mating surface of the crankcase.

1B3-84 OM600 ENGINE MECHANICAL
3 Crankshaft Main Bearing Shells (Upper)
4 Thrust Bearings (Upper)
5 Crankshaft
6 Crankshaft Main Bearing Shells (Lower)
7 Thrust Bearings (Lower)A Radial Bearings
B Radial and Axial Bearings (Thrust Bearing)
Notice
The gaps between the bearing shell and bore and
between the bearing shell and journal are different
each other. Refer to service data.
Thrust Washer and Bearing Arrangement
OM662LA Engine

OM600 ENGINE MECHANICAL 1B3-85
3 Crankshaft Main Bearing Shells (Upper)
4 Thrust Bearings (Upper)
5 Crankshaft
6 Crankshaft Main Bearing Shells (Lower)
7 Thrust Bearings (Lower)A Radial Bearings
B Radial and Axial Bearings (Thrust Bearing)
Notice
The gaps between the bearing shell and bore and
between the bearing shell and journal are different
each other. Refer to service data.
OM661LA Engine

OM600 ENGINE MECHANICAL 1B3-105
VALVE SPRINGS CHECK
Preceding Work : Removal of valve spring
1 Valve Spring
Service Data
Outer diameter
33.1mmWire diameter
4.20mmFree length
50.0mmAt preloaded
Length Tension (new)
680 - 740N 27mmLimit
612N
2 Spring Scale