check engine SSANGYONG MUSSO 1998 Workshop Workshop Manual

1B2-64 M161 ENGINE MECHANICAL
7. Unscrew the bolt (3) from the armature (4) and remove
the roll pin, and remove the armature.
Installation Notice
Tightening Torque 35 Nm
8. Unscrew the nut (6) and remove the seal cover (7).
Installation Notice
Tightening Torque 60 - 70 Nm
Notice
Put the locking slot of nut toward armarture.
9. Take off the timing chain from intake camshaft sprocket.
10. Remove the cover (7), adjuster piston (9) and conical
spring (10) from intake camshaft sprocket.
11. Unscrew the bolt (11) and remove the flange shaft.
Installation Notice
Tightening Torque1st step 20 Nm
2nd step + 95°
Notice
The flange bolt is designed to be used only once, so always
replace with new one.
12. Installation should follow the removal procedure in the
reverse order.
13. Check and adjust the camshaft timing.

1B2-68 M161 ENGINE MECHANICAL
7. Remove the bearing cap, and remove the intake and the
exhaust camshaft.
Installation Notice
Tightening Torque 22.5 - 27.5 Nm
Notice
Check the numbers on the bearing cap not to be miked
up.
8. Apply the engine oil on the valve tappet and camshaft
bearing.
9. Installation should follow the removal procedure in the
reverse order.
Notice
lBase circle of cam should cantact with the valve tappet.
lInstall the camshaft bearing caps according to the
numbers on the cylinder head cast and bearing cap.
10. Check the camshaft timing position.

1B2-70 M161 ENGINE MECHANICAL
Tools Required
104 589 01 01 00 Spanner
111 589 03 15 00 Insert Pin
Inspection Procedure
1. Position the NO.1 cylinder piston to ATDC 20° by turning
the crankshaft
Notice
When the ATDC 20° mark on vibration damper is aligned
with timing gear case cover, the intake and exhaust cam of
cylinder will make the slope to the center and will face up.
In this way, the insert hole in NO.1 and NO.4 camshaft
bearing cap will match in line with the flange hole for
camshaft sprocket.
2. Check the timing as below procedure;
- Check if the insert pin (111 589 03 15 00) can be inserted
into the NO.1 and NO.4 bearing cap hole.
- At this condition, check if the ATDC 20° mark on vibration
damper aligns with the marker on the timing gear case.

M161 ENGINE MECHANICAL 1B2-71
Adjustment Procedure
1. Position the NO.1 cylinder to ATDC 20° .
2. Remove the chain tensioner.
3. Remove the exhaust camshaft sprocket.
4. Adjust the timing position with inserting the insert pin
(
f6.5mm, 111 589 03 15 00) into the NO.1 and NO.4
camshaft bearing cap hole and flange hole while rotating
the camshaft by using wrench (104 589 01 01 00).
5. Install the chain to the intake camshaft sprocket.
6. Install the chain to the exhaust camshaft sprocket and
tighten the bolt.
Installation Notice
Tightening Torque1st step 20 Nm
2nd step + 90°
The sprocket bolt is designed to be used only once, so
replace with new one.
7. Install the chain tensioner.
Installation Notice
Screw plug
Tensioner assembly40 Nm
80 ± 8 Nm Tightening
Torque
8. Check the camshaft timing.

1B2-72 M161 ENGINE MECHANICAL
VALVE SPRING
Preceding Work : Removal of camshaft
Removal of spark plug
1 Valve Tappet Assembly
2 Valve Cotter
3 Upper Retainer
4 Valve Spring..........Check, Replace if necessary
5 Valve Stem Seal
6 Lower Retainer7 Connecting Hose
8 Thrust Piece
9 Slide
10 Adjust Bolt
11 Lever Pusher
12 Supporting Bar

1B2-74 M161 ENGINE MECHANICAL
8. Install the lever pusher (11) and the thrust piece (8) to the
slide (9).
13. Remove the valve cotter (2) using either the pincette (13)
or magnetic finger.
Lever Pusher 111 589 18 61 00
Magnetic Finger 116 589 06 63 00
9. Mount the thrust piece (8) vertically to the valve spring
retainer (3).
10. Make the thrust piece (8) and the slide (9) perpendicular
to each other.
11. Secure the slide (9) by turning the adjust bolt (10).
12. Press the valve spring (4) by using the lever pusher (11).
14. Remove the upper retainer (3) and the valve spring (4).
15. Remove the valve stem seal and replace if necessary.
Notice
Check the valve stem seal and replace if necessary.
16. Remove the lower retainer (6).
Notice
Check the retainer for damages and replace with a new
one if necessary.
17. Installation should follow the removal procedure in the
reverse order.

1B2-76 M161 ENGINE MECHANICAL
VALVE STEM SEAL
Preceding Work : Removal of valve spring
1 Drift (Special Tool)
2 Valve Stem Seal
3 Protective Sleeve
Drift 119 589 00 43 00 Pliers 104 589 00 37 00
Tools Required
104 589 00 37 00 Pliers
119 589 00 43 00 Drift
Replacement Procedure
1. Remove the valve stem seal (2) using the pliers.
Notice
Check the valve stem seal for damage and replace if
necessary.
2. Coat the valve stem seal with oil and assemble it with the
protective sleeve.
3. Insert the valve stem seal by pressing it with the drift.

M161 ENGINE MECHANICAL 1B2-77
CHAIN TENSIONER
1 Screw Plug................................................ 40 Nm
2 Seal
3 Filler Pin
4 Compression Spring5 Snap Ring
6 Thrust Pin
7 Chain Tensioner Housing.....................72-88 Nm
8 Seal
Removal Procedure
1. Position the number 1 cylinder to ATDC 20°.
Notice
Remove the oil filler cap at adjustment position, and check
whether the intake camshaft cam’s lobe (arrow) stays in the
upper side.
2. Cover the alternator with a clean cloth.
3. Release the tension by unscrewing the screw plug once.
Notice
In case that the tension is reduced by unscrewing the screw
plug, reinstall after completely removing the chain tensioner.
If the chain tensioner is tightened again without completely
reducing its tension, then the snap ring doesn’t return to
the original position and the tension gets excedded.

M161 ENGINE MECHANICAL 1B2-79
4. Lightly apply the grease to the seal (2) and install the screw
plug (1).
Installation Notice
Sectional View
1 Screw Plug
2 Ball (Nonreturn Valve)
3 Compression Spring
4 Ball Guide
5 Seal (Aluminum)
6 Filler Pin
7 Compression Spring
8 Snap Ring
9 Thrust Pin
10 Ball (Nonreturn Valve)
11 Compression Spring
12 Thrust Piece13 Chain Tensioner Housing
1 4 Seal
15 Timing Gear Case Cover
16 Cylinder Head
17 Bolt / Washer
18 Tensioning Rail
19 Cylinder Head Gasket
20 Timing Chain
21 Tensioning Rail Base (Sliding Surface)
A Oil Supply Hole
B Chain Tensioner Oil Storage Hole 5. Check for leaks by operating the engine.
Tightening Torque 40 Nm

1B2-84 M161 ENGINE MECHANICAL
17. Rivet the link pin.
Check the condition and it again if necessary.
18. Install the chain tensioner.
Installation Notice
19. Check the camshaft timing position.Tightening TorqueScrew Plug
40 Nm
Tensioner Assembly
72 - 88 Nm