engine SSANGYONG MUSSO 1998 Workshop Repair Manual

M162 ENGINE INTAKE & EXHAUST 1G1-7
RESONANCE FLAP
1 Soft Cap (2)
2 Bolt (M6 x 25, 4 pieces)......................... 9-11 Nm
3 O-ring
Removal & Installation Procedure
1. Remove the 2 soft caps (1).
2. Remove the upper resonance flap coupling after removing
4 bolts (2).
Notice
Connect carefully the vacuum hose (4) for installation.
3. Check the O-ring (3) and replace it if necessary.
4. Remove the lower resonance flap (5).
5. Replace the gasket (6).
6. Installation should follow the removal procedure in the
reverse order.4 Vacuum Hose
5 Resonance Flap
6 Gasket ................................................... Replace

1G1-8 M162 ENGINE INTAKE & EXHAUST
Function Description
A pneumatically actuated resonance flap (5) is located on the
intake manifold, and will be opened and closed by load, which
operates resonance flap according to engine and controlled
by ECU and rpm.
1. Resonance flap closed (at idle/partial load : less than
3,800/rpm)
The switch valve (7) will be adjusted by ECU and resonance
falp will be colosed. By increasing air flow passage through
dividing intaking air flow toward both air collection housing
(8). This leads to a signficant increase in the torque in the
lower speed range.
2. Resonance flap open (at full load : over 3,800/rpm)
The switch valve (7) will not be adjusted by ECU and
resonance falp (5) will be open. The colllected air in the air
collection housing (8) will not be divided and intaking air
passage will be shorten.

M162 ENGINE INTAKE & EXHAUST 1G1-9
EXHAUST MANIFOLD
Preceding Work : Removal of air cleaner
1 Nut .......................................................36-44 Nm
2 Gasket ................................................... Replace3 Exhaust Manifold

1G1-10 M162 ENGINE INTAKE & EXHAUST
Tools Required
103 589 01 39 00 Caulking Bolt
Removal & Installation Procedure
1. Remove the flange bolt from the exhaust manifold, and
disconnect the front exhaust pipe.
Installation Notice
Notice
Check for nut damages and replace the nut if necessary.
2. Remove the 23 nuts (1) from the stud bolt, and remove the
exhaust manifold.
Installation Notice
3. Replace the gasket (2).
4. Installation is reverse order of the removal.
Replacement of Rivet Nut
1. Pull out the rivet nut from the connecting point of the exhaust
manifold and the exhaust pipe using a proper bolt (arrow).
2. Insert a new rivet nut into the exhaust manifold hole, and
tighten with a special tool (Caulking Bolt).
Installation Notice
Caulking Bolt 103 589 01 39 00
Tightening Torque 30 Nm
Tightening Torque 26 - 34 Nm
Tightening Torque 30 Nm

M162 ENGINE INTAKE & EXHAUST 1G1-11
Removal and Installation of Exhaust Line
1 Exhaust Manifold
2 Rivet Nut
3 Bolt........................................................... 30 Nm
4 Front Pipe
5 Oxygen Sensor
6 Bolt......................................................28-47 Nm
7 Rubber Pad
8 Catalytic Converter
9 Gasket ................................................... Replace1 0 Nut
11 Gasket ................................................... Replace
12 Rubber Pad
13 Nut .......................................................28-47 Nm
14 Center Muffler
15 Rubber Pad
16 Tail Muffler
17 Gasket ................................................... Replace
18 Nut .......................................................28-47 Nm

SECTION 1G2
M161 ENGINE INTAKE & EXHAUST
TABLE OF CONTENTS
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Nlm
9 - 11
22.5 - 27.5
22.5 - 27.5
9.5 - 12.5
15 - 28
28 - 47 Application
Air Cleaner Housing Cover Nut
Intake Manifold Bolt (M8 x 20)
Intake Manifold Bolt (M8)
Exhaust Mainfold Stud Bolt
Exhaust Pipe Nut (Engine)
Exhaust Pipe Bolt
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1G2-1
Fastener Tightening Specifications . . . . . . . . 1G2-1
Maintenance and Repair . . . . . . . . . . . . . . 1G2-2
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1G2-2
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 1G2-2Air Intake Shield . . . . . . . . . . . . . . . . . . . . . . 1G2-4
Intake Air Duct . . . . . . . . . . . . . . . . . . . . . . . 1G2-5
Intake Manifold . . . . . . . . . . . . . . . . . . . . . . . 1G2-7
Exhaust Manifold . . . . . . . . . . . . . . . . . . . . . 1G2-9

1G2-2 M161 ENGINE INTAKE & EXHAUST
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
AIR CLEANER
1 Air Cleaner Assembly
2 Element Assembly
3 Insulator
4 Air Duct Hose5 Air Inlet Duct
6 Bolt (M8
× 30 ) ...................................22.5-27.5 Nm
7
Bolt (M6 × 35 ) ........................................... 9-11 Nm

M161 ENGINE INTAKE & EXHAUST 1G2-3
Removal & Installation Procedure
1. Release the clamp securing HFM sensor and air cleaner.
2. Disengage the air cleaner assembly and HFM sensor
assembly.
3. Unserew the mounting bolt(6) from the bracket.
Installation Notice
Tightening Torque 22.5 - 27.5 Nm
4. Release the clamp from air cleaner assembly housing and
remove the cover.
5. Remove the air cleaner assembly.
6. Remove the air cleaner housing from insulator.
Notice
Make sure the air cleaner to be seated in insulator.
7. Disengage the air duct hose and air cleaner housing and
remove the housing.
8. Remove the air duct hose.
9. Unscrew the two bolts(7) from air inlet duct.
Installation Notice
10. Remove the air inlet duct.
11. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 8 - 9 Nm

1G2-4 M161 ENGINE INTAKE & EXHAUST
AIR INTAKE SHIELD
Preceding Work : Removal of air cleaner
Removal & Installation Procedure
1. Remove the upper cover (3) from the air intake shield (5)
upper mounting pin.
2. Remove the bolts (4 and 6).
3. Remove the air intake shield (5).
4. Installation should follow the removal procedure in the
reverse order. 1 Air Cleaner
2 Gasket
3 Air Intake Shield Upper Cover
4 Bolt5 Air Intake Shield
6 Bolt
7 Bracket

M161 ENGINE INTAKE & EXHAUST 1G2-5
INTAKE AIR DUCT
1 Clamp
2 Sleeve
3 HFM Sensor
4 Intake Air Duct
5 Blow-by Hose
7 Clamp(2 pieces)
8 Intake Air Duct Mounting
Bracket
Removal & Installation Procedure
1. Release the clamp (1) and intake air duct.
2. Remove the Blow-by hose (5) (arrow).