check engine SSANGYONG MUSSO 2003 Workshop Manual

1B2-72 M161 ENGINE MECHANICAL
VALVE SPRING Preceding Work : Removal of camshaftRemoval of spark plug
1 Valve Tappet Assembly
2 Valve Cotter
3 Upper Retainer
4 Valve Spring..........Check, Replace if necessary
5 Valve Stem Seal
6 Lower Retainer 7 Connecting Hose
8 Thrust Piece
9 Slide
10 Adjust Bolt 11 Lever Pusher
12 Supporting Bar

1B2-74 M161 ENGINE MECHANICAL8. Install the lever pusher (11) and the thrust piece (8) to the slide (9).
13. Remove the valve cotter (2) using either the pincette (13) or magnetic finger. Lever Pusher 111 589 18 61 00
Magnetic Finger 116 589 06 63 00
9. Mount the thrust piece (8) vertically to the valve spring
retainer (3).
10. Make the thrust piece (8) and the slide (9) perpendicular to each other.
11. Secure the slide (9) by turning the adjust bolt (10).
12. Press the valve spring (4) by using the lever pusher (11).
14. Remove the upper retainer (3) and the valve spring (4).
15. Remove the valve stem seal and replace if necessary.
Notice
Check the valve stem seal and replace if necessary.
16. Remove the lower retainer (6).
NoticeCheck the retainer for damages and replace with a new
one if necessary.
17. Installation should follow the removal procedure in the reverse order.

1B2-76 M161 ENGINE MECHANICAL
VALVE STEM SEAL Preceding Work : Removal of valve spring
1 Drift (Special Tool)
2 Valve Stem Seal
3 Protective Sleeve
Drift 119 589 00 43 00
Pliers 104 589 00 37 00
Tools Required
104 589 00 37 00 Pliers
119 589 00 43 00
Drift
Replacement Procedure
1. Remove the valve stem seal (2) using the pliers. Notice Check the valve stem seal for damage and replace if
necessary.
2. Coat the valve stem seal with oil and assemble it with the protective sleeve.
3. Insert the valve stem seal by pressing it with the drift.

M161 ENGINE MECHANICAL 1B2-77
CHAIN TENSIONER1 Screw Plug ................................................ 40 Nm
2 Seal
3 Filler Pin
4 Compression Spring 5 Snap Ring
6 Thrust Pin
7 Chain Tensioner Housing
.....................72-88 Nm
8 Seal
Removal Procedure
1. Position the number 1 cylinder to A TDC 20°.
Notice Remove the oil filler cap at adjustment position, and check whether the intake camshaft cam ’s lobe (arrow) stays in the
upper side.
2. Cover the alternator with a clean cloth.
3. Release the tension by unscrewing the screw plug once.
NoticeIn case that the tension is reduced by unscrewing the screw
plug, reinstall after completely removing the chain tensioner.If the chain tensioner is tightened again without completely reducing its tension, then the snap ring doesn ’t return to
the original position and the tension gets excedded.

M161 ENGINE MECHANICAL 1B2-79
4. Lightly apply the grease to the seal (2) and install the screwplug (1). Installation Notice
Sectional View
1 Screw Plug
2 Ball (Nonreturn Valve)
3 Compression Spring
4 Ball Guide
5 Seal (Aluminum)
6 Filler Pin
7 Compression Spring
8 Snap Ring
9 Thrust Pin
10 Ball (Nonreturn Valve)
11 Compression Spring
12 Thrust Piece 13 Chain Tensioner Housing
14 Seal
15 Timing Gear Case Cover
16 Cylinder Head
17 Bolt / Washer
18 Tensioning Rail
19 Cylinder Head Gasket
20 Timing Chain
21 Tensioning Rail Base (Sliding Surface)
A Oil Supply Hole
B Chain Tensioner Oil Storage Hole
5. Check for leaks by operating the engine.
Tightening Torque 40 Nm

1B2-84 M161 ENGINE MECHANICAL
17. Rivet the link pin.Check the condition and it again if necessary.
18. Install the chain tensioner. Installation Notice
19. Check the camshaft timing position. Tightening Torque
Screw Plug
40 Nm
Tensioner Assembly 72 - 88 Nm

1B2-92 M161 ENGINE MECHANICAL
1. Check the piston ring gap and apply the engine oil to thepiston pin and the connecting rod bushing.
2. Connect the piston and the connecting rod by pressing in the piston pin (6) and install the snap ring to the groove.
3. Clean the cylinder bore, connecting rod bearing journal, connecting rod bearing shell and the piston and coat them with engine oil.
4. Install the piston ring using the tensioning strap(000 589 04 14 00).
5. Install the piston so that the arrow on the piston head faces to the forward of the vehicle.
6. After aligning the connecting rod and the bearing cap mark (// or a number), tighten the bolts.
Installation Notice
Tightening Torque 1st step 35 - 45 Nm
2nd step 90
°+5 °
Apply the engine oil to the bearing cap upper and lower bearing shells.
7. Check if the crankshaft rotates without any trouble by rotating it.

1B2-94 M161 ENGINE MECHANICAL Inspection
1. Measure the basic bore of the connecting rod bearing.Notice If the basic bore exceeds the value of 51.614mm, replace the bearing or check the connecting rod.
2. Check connecting rod bolts.
3. Check the assembly mark(indication//or number:arrow) of the connecting rods and the bearing cap when installing. Notice
Make sure it doesn ’t exceed over 4g with other
connecting rods when replacing the connecting rods.
Check if the connecting rod and the bearing cap are accurately seated on the groove when replacing the bearing.
Notice If the length exceeds max. length, replace it.
Length When New (L)
Max. Length (L)
Tightening Torque 51.7 - 52 mm
52.9 mm
1st step 40 + 5 Nm 2nd step 90 °+10 °

M161 ENGINE MECHANICAL 1B2-97
OIL PAN
1 Bolt
2 Bolt
3 Bolt
4 Bolt
1. Remove the drain plug and drain the oil completely.
2. Unscrew the bolts and remove the oil pan and gasket. Notice Arrange the bolts according to each size.
3. Clean the inside of oil pan and sealing surface, then apply the sealant.
4. Replace the gasket with new one.
5. Install the oil pan with gasket, and tighten each bolt in specified torque.
6. Check for oil leaks while running the engine.
M8 X 40, 4 pieces M6 X 35, 1 piecesM6 X 100, 2 pieceM6 X 85, 3 piecesM6 X 20, 20 pieces5 Bolt
6 Oil Pan
7 Gasket

1B2-100 M161 ENGINE MECHANICAL9. Fill up engine oil through the engine oil filler opening.
10. Check for oil leaks at normal engine temperature after starting the engine.
11. Stop the engine and wait 5 minutes. Check the oil level and fill up as specified if necessary.
4. Remove the drain plug (1) and drain the engine oil.
Notice Leave the oil filler cap (3) open to ease the engine oil discharge.
5. Tighten the engine oil drain plug after cleaning it. Installation Notice
Tools Required
103 589 02 09 00 Oil Filter Socket Wrench Replacement Procedure
1. Install the socket wrench ”7” (special tool : 103 589 02 09
00) on the oil filter cover (2). NoticeMake the screw cover removable by tightening the bolt at the side of the socket wrench (special tool).
2. Install the wrench to the upper bolt in the socket wrench and remove the oil cover by turning it.
3. Remove the oil filter element.
Notice Work with a cloth under the vehicle when removing the oil filter element to not drain the oil. Replace the seal washer with new one.
6. Replace the O-ring(5) in the oil filter cover with new one.
Notice Apply the engine oil to the O-ring.
7. Insert new oil filter element into the oil filter housing.
Tightening Torque 25 Nm
8. Temporarily tighten the oil filter cover (2). Install the socket wrench “7” (special tool : 103 589 02 09 00), and then
completely tighten it. Installation Notice
2 Oil Filter Cover
5 O-ring
6 Oil Filter Element
7 Special Tool (Socket Wrench)
Tightening Torque 25 Nm