torque SUBARU FORESTER 2004 Service Service Manual

SE-4
SEAT
General Description
2. REAR SEAT
(1) Webbing guide cap (8) Seat cushion cover (15) Backrest cover LH
(2) Webbing guide (9) Seat cushion pad (16) Backrest frame LH
(3) Center pillow (10) Hinge CTR (17) Backrest pad LH
(4) Headrest free bushing (11) Hinge LH
(5) Backrest cover RH (12) HeadrestTightening torque: N·m (kgf-m, ft-lb)
(6) Backrest frame RH (13) Rear backrest knobT1: 24.5 (2.5, 18.1)
(7) Backrest pad (14) StrikerT2: 33 (3.3, 24.6)
SE-00253
(1)
(2)
(4)(3)
(8)(5) (6)
(7)
(9)
(10) T2
T2 T2
T1T1 T2
T2(12)
(13)(4)
(14)
(11) (17) (16)
(15)

SE-6
SEAT
Front Seat
2. Front Seat
A: REMOVAL
1) Disconnect the ground cable from battery.
WARNING:
The airbag system is fitted with a backup power
source. If the airbag system is serviced within 20
seconds after the ground cable is disconnected,
it may inflate.
2) While pressing the headrest lock button, remove
the headrest.
3) Tilt forward the backrest.
4) Move the seat to full front end.
5) Remove the bolt cover at rear end of slide rail.
6) Remove the two bolts at rear side of seat rail.
7) Move the seat to full rear end.8) Remove the two bolts at front side of seat rail.
9) Disconnect the side airbag connector under
seat.
 Side airbag connector
 Seat belt warning light connector (Driver’s seat)
 Seat heater connector (Model with seat heater)
10) Remove the front seat from the vehicle.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
Refer to COMPONENT in General Descrip-
tion. NENT, General Description.>
C: DISASSEMBLY
1. DRIVER’S SEAT
1) Remove the seat from the vehicle. 6, REMOVAL, Front Seat.>
2) Remove the reclining lever and reclining hinge
cover.
SE-00003
SE-00048
SE-00049
SE-00006
SE-00050
SE-00040

SE-11
SEAT
Front Seat
14) Loosen the bolts and nuts to remove the seat
cushion from slide rail.
15) Remove the inner belt.
16) Remove the hooks (A), and then remove the
seat cushion frame.17) Remove the hog rings (A), and then remove the
seat cushion cover from seat cushion pad.
18) Open the zipper at bottom of headrest, and
then remove the headrest cover from headrest.
D: ASSEMBLY
1. DRIVER’S SIDE
Assemble in the reverse order of disassembly.
2. PASSENGER’S SIDE
Assemble in the reverse order of disassembly.
CAUTION:
Because it may cause the side airbag to acti-
vate incorrectly, observe the following steps to
install the side airbag correctly.
 Be careful not to dirty or damage the backrest
cover.
 Always use new hog rings.
 Secure the hog ring using hog ring pliers.
 Install the hog ring to its original position,
and not to twist or wrinkle the backrest cover.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. NENT, General Description.>
SE-00306
SE-00307
SE-00268
(A)
SE-00299
: (A)
SE-00271

SE-13
SEAT
Rear Seat
3. Rear Seat
A: REMOVAL
1) Remove the bolts, and then detach the rear seat
cushion.
2) Remove the headrest.
3) Remove the luggage floor mat.

4) Fold down the rear seat backrest.
5) Turn over the mat to remove bolts.
6) Remove the rear seat backrest.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
Refer to COMPONENT in General Descrip-
tion. NENT, General Description.>
C: DISASSEMBLY
1) Remove the rear seat. AL, Rear Seat.>
2) Remove the hog rings (A) from around the seat
backrest.
3) Remove the hog rings (A) on front side of cush-
ion pad, and then remove the cover.
4) Remove the hog rings (A) from around the seat
cushion.
5) Remove the hog rings (A), and then remove the
cover.
SE-00023
SE-00153
SE-00025
: (A)SE-00154
: (A)
SE-00155
: (A)
SE-00156
: (A)
SE-00157

SL-2
SECURITY AND LOCK
General Description
1. General Description
A: COMPONENT
1. DOOR LOCK ASSEMBLY
Without double lock:
(1) Inner remote ASSY (5) Striker Tightening torque: N⋅m (kgf-m, ft-lb)
(2) Inner remote cover (6) Door outer handleT1: 6.4 (0.65, 4.7)
(3) Auto-door lock actuator (7) Key cylinderT2: 7.4 (0.75, 5.5)
(4) Door latch T3: 17.6 (1.8, 13.0)
SL-00288
T1
T1
T3
T3
T2
T2 (1)
(2)
(3)
(1)
(2)(3)
(4)(4)
(5)(5)
(6)(6)
(7)
T2
T2
T2

SL-3
SECURITY AND LOCK
General Description
With double lock:
(1) Inner remote ASSY (6) Door outer handleTightening torque: N⋅m (kgf-m, ft-lb)
(2) Inner remote cover (7) Key cylinder (switch)T1: 6.4 (0.65, 4.7)
(3) Auto-door lock actuator (8) Key cylinder retainerT2: 7.4 (0.75, 5.5)
(4) Door latch (9) Key cylinder retainer coverT3: 17.6 (1.8, 13.0)
(5) Striker
SL-00289
T1
T1
T3
T3
T2
T2 (1)
(2)
(1)
(2)(3)
(4)(4)
(5)(5)
(3)
(6)(6)
(7)
(8)
(9)
T2
T2
T2
T2

SL-4
SECURITY AND LOCK
General Description
2. REAR GATE LOCK
(1) Rear gate latch ASSY (3) Striker Tightening torque: N⋅m (kgf-m, ft-lb)
(2) Rear gate actuator (4) Rear gate outer handleT1: 7.5 (0.75, 5.4)
T2: 25 (2.5, 18.4)
SL-00103
T1
T2
T2(1) (2)
(3)(4)

SL-5
SECURITY AND LOCK
General Description
3. HOOD LOCK AND REMOTE OPENERS
(1) Hood lock ASSY (4) Pull handle ASSYTightening torque: N⋅m (kgf-m, ft-lb)
(2) Lever ASSY (5) Fuel flap cable ASSYT1: 7.4 (0.75, 5.4)
(3) Hood cable ASSYT2: 33 (3.4, 24.6)
SL-00104
T1
T2
(5) (4)
(2)
(3)
(1)

SR-2
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
General Description
1. General Description
A: COMPONENT
(1) Sunroof lid (7) Harness (13) Shim
(2) Rear drain ASSY (8) Sunshade
(3) Frame ASSY (9) GarnishTightening torque: N·m (kgf-m, ft-lb)
(4) Motor ASSY (10) Frame bracketT: 7.4 (0.75, 5.4)
(5) Drive unit (11) Cover
(6) Drain tube (12) Deflector
SR-00013
T
T
T
T
(1)
(2)
(3)
(4)(5)
(6)
(7)
(12)(13)
(11)
(6)(10)(8)
(9)

EI-2
EXTERIOR/INTERIOR TRIM
General Description
1. General Description
A: COMPONENT
1. FRONT GRILLE
2. UNDER COVER
(1) Front grille (3) Clip (4) Hook
(2) Front grille emblem
(1) Under cover (3) ClipTightening torque: N·m (kgf-m, ft-lb)
(2) Service hole cover (4) BoltT: 18 (1.84, 13.3)
EI-00230 (1)
(2)(3)
(4)
EI-00002 (1)
T
T
(2) (3)
(4)
(3)(3)