Back up SUBARU TRIBECA 2009 1.G Service Repair Manual

SB-5
General Description
SEAT BELT SYSTEM
B: CAUTION
•Before starting the work, turn the ignition switch
to OFF, disconnect the battery ground cable and
wait for 20 seconds or more.
•The pretensioner system has a backup power
source. The pretensioner might deploy if you do not
wait for 20 seconds or more before starting work.
•Do not drop or apply any impact to the preten-
sioner.
•If oil, grease or water gets on the pretensioner,
wipe it off immediately with a dry cloth.
•Do not expose the pretensioner to high tempera-
ture or flame.
•Do not allow current to flow through or voltage to
reach the pretensioner. Do not use a circuit tester
to check resistance of the pretensioner.
•Do not disassemble or attempt to repair the pre-
tensioner. If it is dented, cracked or deformed, re-
place it with a new one.
•Do not use the airbag or pretensioner parts from
other vehicles. Always replace parts with new
parts.
•When handling a seat belt with deployed preten-
sioner, wear gloves and goggles. Wash your hands
afterwards.
•Do not reuse a seat belt with deployed preten-
sioner.
•If material from the airbag enters the eyes or con-
tacts skin during deployment, wash it away with
clean water, and then consult a doctor.
C: PREPARATION TOOL
1. GENERAL TOOL
TOOL NAME REMARKS
TO RX® T50Used for removing and installing the inner seat belt assembly.

SB-10
Front Seat Belt
SEAT BELT SYSTEM
5. Front Seat Belt
A: REMOVAL
1. OUTER SEAT BELT ASSEMBLY
1) Fold the backrest all the way forward, and then
move the front seat all the way forward.
2) Turn the ignition switch to OFF, disconnect the
battery ground cable, and wait more than 20 sec-
onds.
3) Remove the center pillar lower trim and center
pillar upper trim. LOWER TRIM, REMOVAL, Side Trim.> EI-44, CENTER PILLAR UPPER TRIM, REMOV-
AL, Side Trim.>
4) Remove the bolt, and then remove the shoulder
anchor.
5) Remove the bolt, and then remove the adjust-
able anchor assembly.
6) Disconnect connector (A) of the pretensioner,
and remove the lower anchor bolt and seat belt re-
tractor.
7) On the passenger side, disconnect connector of
the belt tension sensor.
CAUTION:
•Do not drop or subject the pretensioner to
any impact.
•Since the pretensioner and bracket are inte-
grated as a unit, do not disassemble them.
2. INNER SEAT BELT ASSEMBLY
1) Turn the ignition switch to OFF, disconnect the
battery ground cable, and wait more than 20 sec-
onds.
2) Remove the four bolts in the slide rail LH and
RH.
3) Disconnect the seat belt warning light connector
under the seat.
4) Remove the harness clips from the back of the
seat.
5) Remove the TORX® bolt, and then remove the
inner seat belt assembly.
SB-00152
SB-00153
SB-00306
(A)
SB-00319
SB-00307

SB-12
Second Seat Belt
SEAT BELT SYSTEM
6. Second Seat Belt
A: REMOVAL
1. OUTER SEAT BELT RH ASSEMBLY AND
LH ASSEMBLY
1) Remove the second row seats. REMOVAL, Second-row Seats.>
2) Remove the third-row seats. REMOVAL, Third-row Seats.>
3) Remove the rear quarter trim. REMOVAL, Rear Quarter Trim.>
4) Remove the lower anchor bolt.
5) Remove the bolt to remove outer seat belt re-
tractor.
2. SHOULDER SEAT BELT CENTER AS-
SEMBLY
1) Remove the rear quarter trim. REMOVAL, Rear Quarter Trim.>
2) Remove the cover (A) from roof trim, and then
insert it to the inside of roof trim.
3) Remove the clips, and then lower the roof trim
end.
CAUTION:
When removing the roof trim clip, do not pull
the roof trim end backward with excessive
force, otherwise roof trim may be damaged.
4) Remove the bolt to remove the seat belt retrac-
tor.
3. INNER SEAT BELT RH ASSEMBLY
1) Remove the RH second-row seat assembly.
ond-row Seats.>
2) Remove the LH hinge outer cover.
3) Remove the bolt, and then detach the inner belt
assembly.
SB-00308
SB-00309
SB-00236
(A)
SB-00155
SB-00316
SB-00310

SB-13
Second Seat Belt
SEAT BELT SYSTEM
4. SHOULDER SEAT BELT CENTER
BUCKLE
1) Remove the LH second-row seat assembly.
ond-row Seats.>
2) Remove the RH hinge outer cover.
3) Remove the bolt, and then remove the shoulder
seat belt center buckle.
5. INNER SEAT BELT LH ASSEMBLY
1) Remove the LH second-row seat assembly.
ond-row Seats.>
2) Remove the bolt from the back of the seat cush-
ion, and then detach the inner belt assembly.
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
When installing, be careful of the routing of the
seatbelt, and make sure that the belt is not
twisted.
C: INSPECTION
Check for the following, and replace with new parts
if necessary.
•Seat belt is slackened, bent or worn. Seat belt is
abnormally wound or extended.
•Inner belt is deformed or damaged.
•Seat belt buckle cannot be engaged properly.
SB-00311
SB-00312

SE-2
General Description
SEATS
1. General Description
A: COMPONENT
1. FRONT SEAT (DRIVER’S SEAT)
(1) Backrest cover (11) Rear leg cover inside (21) Power seat switch unit
(2) Backrest pad (12) Seat cushion cover (22) Seat heater unit
(3) Backrest frame ASSY (13) Seat cushion pad (23) Lumber support lever
(4) Headrest ASSY (14) Seat cushion frame ASSY (24) Slide rail cover
(5) Headrest lock bushing (15) Rear leg cover outside
(6) Side airbag module (16) Power seat switch knobTightening torque: N·m (kgf-m, ft-lb)
(7) Cover frame (17) Seat side cover outsideT1: 6 (0.61, 4.43)
(8) Backrest back cover (18) Hinge inner cover LHT2: 17.6 (1.79, 12.7)
(9) Seat side cover inside (19) Inner seat belt ASSYT3: 52 (5.30, 37.6)
(10) Hinge inner cover RH (20) Slide rail ASSYT4: 53 (5.40, 38.3)
(1)
(2)
(23)
(22)
(3)
(8)
(4)
(5)
(6)(9)
(10)(11)
(12)
(13)
(14)
(15)
(17)
(21)(19)
(18)
T4
T4
T2
T3
T1
T2
T3
(7)
(24)
(24)
T4
(16)
(20)
SE-00580

SE-3
General Description
SEATS
2. FRONT SEAT (DRIVER’S SEAT)
(1) Backrest cover (10) Hinge inner cover LH (19) Power seat switch unit
(2) Backrest pad (11) Rear leg cover inside (20) Inner seat belt ASSY
(3) Backrest frame ASSY (12) Seat cushion cover (21) Slide rail cover
(4) Headrest ASSY (13) Seat heater unit
(5) Headrest lock bushing (14) Seat cushion pad & frame ASSYTightening torque: N·m (kgf-m, ft-lb)
(6) Side airbag module (15) Rear leg cover outsideT1: 6 (0.61, 4.43)
(7) Cover frame (16) Hinge inner cover RHT2: 17.6 (1.79, 12.7)
(8) Backrest back cover (17) Seat side cover outsideT3: 52 (5.30, 37.6)
(9) Seat side cover inside (18) Power seat switch knobT4: 53 (5.40, 38.3)
T3
T3
(1)
(2)
(3)
(8)
(4)
(5)
(6)
(9)
(10)
(12)
T4
T2
T2
T1
T4
(7)
(11)
(15)
(14)
(21)
(20)
(16)
(13)
(19)
(18)
(17)
SE-00581

SE-4
General Description
SEATS
3. SECOND-ROW SEATS
(1) Headrest (8) Backrest back cover (14) Armrest
(2) Lock bushing (9) Holder (15) Slide rail cover
(3) Backrest cover (10) Seat back latch cover
(4) Backrest pad (11) Hinge outer coverTightening torque: N·m (kgf-m, ft-lb)
(5) Seat cushion cover (12) Hinge inner coverT1: 40 (4.08, 28.9)
(6) Seat cushion pad (13) Cup holderT2: 52 (5.30, 37.6)
(7) Slide rail ASSY
(1)
(1)
(8)
(8)
(3)
(3)
(5)
(6)
(4)
(4)
(11)
(11)
(11)(10)
(12)
(12)
(15)
(15)(7)
(15)
(2)
(2)
(9)
T2
T2
T1
T2
T2
T2
T1
(8)
(9)
(2)
(12)
(14)
(13)
(7)
(12)
(12)
(11)
(11)
SE-00582

SE-5
General Description
SEATS
4. THIRD-ROW SEATS
(1) Headrest (7) Backrest padTightening torque: N·m (kgf-m, ft-lb)
(2) Headrest lock bushing (8) Seat cushion coverT1: 10 (1.01, 7.23)
(3) Hinge lever ASSY (9) Seat cushion padT2: 52 (5.30, 37.6)
(4) Backrest back cover (10) Hinge plateT3: 53 (5.40 38.3)
(5) Backrest frame (11) Inner hinge ASSY
(6) Backrest cover
(1)
(2)
(2)(3)
(3)
(6)
(7)
(8)
(9)
(4)
(5)
(10)
(11)
T3
T3
T3
T1
T3
T1
T2
SE-00583

SE-7
Front Seat
SEATS
2. Front Seat
A: REMOVAL
CAUTION:
The airbag system is fitted with a backup power
source. After disconnecting the battery ground
cable, the airbag may deploy if you do not wait
for 20 seconds before starting the service of
airbag system.
1. DRIVER’S SEAT
1) Remove the headrest.
2) Tilt the backrest forward, and move the seat for-
ward.
3) Remove the rear leg cover, and remove the two
bolts at the rear side of slide rail.
4) Move the seat backward, remove the front leg
cover, and then remove the 2 bolts at the front side
of the slide rail.
5) Disconnect the ground cable from battery, and
wait for more than 20 seconds before starting work.
6) Disconnect the connector under the seat.
•Seat belt buckle switch connector
•Seat position sensor connector
•Side airbag connector
•Seat heater connector
•Power seat connector
7) Remove the seat from vehicle.
2. PASSENGER’S SEAT
CAUTION:
Refer to “CAUTION” of “General Description”
before starting the work. TION, General Description.>
1) Remove the headrest.
2) Tilt the backrest forward, and move the seat for-
ward.
3) Remove the rear leg cover, and remove the bolt
at the rear side of the slide rail.
4) Move the seat backward, remove the front leg
cover, and then remove the bolt at the front side of
the slide rail.
5) Disconnect the ground cable from battery, and
wait for more than 20 seconds before starting work.
6) Disconnect all the connectors of connector hold-
er in the backside of seat cushion.
•Harness connector of occupant detection control
module
•Side airbag connector
•Power seat connector
•Seat heater connector
7) Remove the seat belt anchor cover.
NOTE:
Tilt the seat back all the way to provide workspace.
8) Remove the seat from vehicle.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
Tighten the slide rail installing bolt gradually in sev-
eral steps to the specified torque in the order as
shown in the figure.
CAUTION:
After installing the driver’s seat, use the Subaru
Select Monitor to confirm that the seat position
sensor LH is operating properly. ag)-32, DISPLAY OF STATUS INFORMATION,
OPERATION, Subaru Select Monitor.>
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. Description.>
C: DISASSEMBLY
1. DRIVER’S SEAT
1) Remove the seat from vehicle. DRIVER’S SEAT, REMOVAL, Front Seat.>
2) Remove the clip (A) and straps (B) on the back
of seat cushion.
3) Disconnect the following connectors from the
backside of seat cushion.
•Side airbag
•Seat position sensor
•Seat heater
•Power seat
•Seat belt
SE-00479
(1)
(3)
(4)
(2)
(B)(A)
SE-00643

SE-8
Front Seat
SEATS
4) Remove the screw (A) and clips (B), and then
disconnect the seat switch connector to remove
seat side cover outside.
5) Remove the TORX® bolt, and then remove the
inner seat belt assembly.
6) Remove the screw (A) and clip (B), and then re-
move the seat side cover inside.
7) Remove the two bolts from the reclining hinge on
each left and right side.
8) Remove the clips and hooks, and then detach
the backrest back cover.
9) Remove the lock clip, and then remove the lum-
ber support lever.
(B)
(B)(A)
SE-00584
SE-00585
SE-00412
(A)(B)
SE-00413
SE-00586
SE-00414