SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual

SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual SWIFT 2000 1.G SUZUKI SUZUKI https://www.carmanualsonline.info/img/20/7606/w960_7606-0.png SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual

Page 241 of 698

SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual 3E-28 REAR SUSPENSION
16) Remove axle housing.
INSTALLATION
Install removed parts in reverse order of removal, noting the fol-
lowing.
1) Place rear axle housing on floor jack. Then install rear trail

Page 242 of 698

SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual REAR SUSPENSION 3E-29
4) Install lateral rod (1) and install bolt (3) in proper direction as
shown. At this time, mount bolt and nut (4) but don’t tighten
them.
5) Clean mating surfaces of axle hous

Page 243 of 698

SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual 3E-30 REAR SUSPENSION
13) Connect brake pipe to wheel cylinder (1) and tighten brake
pipe flare nut (2) to specified torque.
Tightening torque
Brake pipe flare nut (b) : 16 N·m (1.6 kg-m, 11.5 lb-ft)

Page 244 of 698

SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual REAR SUSPENSION 3E-31
21) Install wheel and tighten wheel nuts to specified torque.
Tightening torque
Wheel nuts (f) : 85 N·m (8.5 kg-m, 61.5 lb-ft)
22) Upon completion of all jobs, pull parking brak

Page 245 of 698

SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual !"#!$%&"&%()(*"+(,-+
&".),&"/%("&0,1"%23"&,4
(*"1,4%3--4
2567895:&7;<==7>?7?%()@)A,%B8<?C;6
D*586%+C=E78F)G7
!"#$"%&()*+,* -./.01-.2345436-3768
799:::;<=:>:8? 6@A*,$+B#C"A,*+A
? D$**AE*+)"

Page 246 of 698

SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual WHEELS AND TIRES 3F-1
6F1
6F2
6G
3F
8A
8B
8C
8D
8E
9
10
10A
10B
SECTION 3F
WHEELS AND TIRES
CONTENTS
GENERAL DESCRIPTION ............................... 3F-2
TIRES ....................................

Page 247 of 698

SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual 3F-2 WHEELS AND TIRES
GENERAL DESCRIPTION
TIRES
This vehicle is equipped with the following tire.
Tire size
: 165/70R14
The tire is of tubeless type. The tire is designed to operate satisfactorily wit

Page 248 of 698

SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual WHEELS AND TIRES 3F-3
HOW TO MEASURE WHEEL RUNOUT
To measure the wheel runout, it is necessary to use an accurate
dial indicator. The tire may be on or off the wheel. The wheel
should be installed to

Page 249 of 698

SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual 3F-4 WHEELS AND TIRES
Dynamic balance, as shown in left figure, is the equal distribution
of weight on each side of the wheel centerline so that when the
tire spins there is no tendency for the assemb

Page 250 of 698

SUZUKI SWIFT 2000 1.G RG413 Service Workshop Manual WHEELS AND TIRES 3F-5
MAINTENANCE AND MINOR ADJUSTMENTS
WHEEL MAINTENANCE
Wheel repairs that use welding, heating, or peening are not approved. All damaged wheels should be replaced.
WHEEL ATTACHING S