high beam TOYOTA CAMRY 2021 Owners Manual (in English)

3
1
8 7 5 4
3
2
CAMRY_U
9
6
3-1. Key informationKeys .................................. 138
3-2. Opening, closing and locking the doors
Doors................................. 147
Trunk ................................. 156
Smart key system.............. 161
3-3. Adjusting the seats Front seats ........................ 169
Rear seats ......................... 171
Head restraints .................. 173
3-4. Adjusting the steering wheel and mirrors
Steering wheel .................. 175
Inside rear view mirror....... 177
Outside rear view mirrors ............................. 179
3-5. Opening and closing the windows
Power windows ................. 181
Moon roof .......................... 185
Panoramic moon roof ........ 189 4-1. Before driving
Driving the vehicle ............. 196
Cargo and luggage ............ 205
Vehicle load limits .............. 208
Trailer towing ..................... 209
Dinghy towing .................... 210
4-2. Driving procedures Engine (ignition) switch (vehicles without a
smart key system) ........... 211
Engine (ignition) switch (vehicles with a
smart key system) ........... 213
Automatic transmission ..... 219
Turn signal lever ................ 225
Parking brake .................... 226
Electric parking brake ........ 227
Brake Hold ......................... 231
4-3. Operating the lights and wipers
Headlight switch ................ 233
AHB (Automatic High Beam) .............................. 238
Windshield wipers and washer ............................. 242
4-4. Refueling Opening the fuel tank cap................................... 246
3Operation of each
component4Driving

18Pictorial index
CAMRY_U
■Switches
Automatic High Beam switch . . . . . . . . . . . . . . . . . . . . . . . . P. 238
VSC OFF switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 328
Camera switch
*1, 2
Trunk opener switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 156
Fuel filler door opener switch . . . . . . . . . . . . . . . . . . . . . . . . P. 248
Heated steering wheel switch
*1. . . . . . . . . . . . . . . . . . . . . . P. 412
“ODO/TRIP” switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 97, 111
Instrument panel light control switch . . . . . . . . . . . . . . . . . . P. 93
Outside rear view mirror switch . . . . . . . . . . . . . . . . . . . . . . P. 179
Door lock switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 151
Power window switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 181
Window lock switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 181
1
2
3
4
5
6
7
8
9
10
11
12

892. Instrument cluster
2
Instrument cluster
CAMRY_U
The indicators inform the driver of the operating state of the vehicle’s
various systems.
Indicators
Turn signal indicator
( P. 225)*1
(if equipped)
Brake hold standby
indicator ( P. 231)
(U.S.A.)
Headlight indicator
(P. 233) Cruise control indicator
(
P. 294, 310)
(Canada)
Tail light indicator
(P. 233) Dynamic radar cruise
control indicator
(
P. 294, 310)
Headlight high beam
indicator ( P. 234) Cruise control “SET”
indicator
(
P. 294, 310)
*1Automatic High Beam
indicator ( P. 238)*1, 3PCS warning light
(P. 258)
*1, 2
Eco driving indicator
(P. 107, 124)*1, 3
(if equipped)
PKSB OFF indicator
(P. 362)
(U.S.A.)
Parking brake indicator
(P. 226, 227)
(White)
LTA indicator ( P. 283)
(Canada)
Parking brake indicator
(P. 226, 227)
(Green)
LTA indicator
(P. 259, 283)
*1
(if equipped)
Brake hold operated
indicator ( P. 231)*4
(Yellow)
LTA indicator ( P. 283)

195
4Driving
CAMRY_U4-1. Before driving
Driving the vehicle ............. 196
Cargo and luggage ........... 205
Vehicle load limits ............. 208
Trailer towing..................... 209
Dinghy towing ................... 210
4-2. Driving procedures Engine (ignition) switch (vehicles without a
smart key system) ........... 211
Engine (ignition) switch (vehicles with a
smart key system) ........... 213
Automatic transmission ..... 219
Turn signal lever................ 225
Parking brake .................... 226
Electric parking brake........ 227
Brake Hold ........................ 231
4-3. Operating the lights and wipers
Headlight switch ................ 233
AHB (Automatic High Beam) ............................. 238
Windshield wipers and washer ............................ 242
4-4. Refueling Opening the fuel tank cap .................................. 246 4-5. Using the driving
support systems
Toyota Safety Sense 2.5+ ................................. 250
PCS (Pre-Collision System)........................... 258
LTA (Lane Tracing Assist) ............................. 274
RSA (Road Sign Assist) .... 289
Dynamic radar cruise control with full-speed
range............................... 294
Dynamic radar cruise control ............................. 310
Driving assist systems ...... 326
BSM (Blind Spot Monitor)........................... 334
• BSM function ................ 339
Intuitive parking assist....... 342
RCTA (Rear Cross Traffic Alert) ............................... 350
• RCTA function .............. 352
Rear Camera Detection Function .......................... 357
PKSB (Parking Support Brake) ............................. 361
Parking Support Brake function
(static objects)................. 368
Parking Support Brake function (rear-crossing
vehicles).......................... 377
Driving mode select switches .......................... 384
4-6. Driving tips Winter driving tips ............. 386

2344-3. Operating the lights and wipers
CAMRY_U
For CanadaThe headlights, day-
time running lights ( P.
235) and all the lights
listed below turn on and
off automatically.
(Vehicles without a
smart key system:
When the engine
switch is in the “ON”
position)
(Vehicles with a smart
key system: When the
engine switch is in
IGNITION ON mode)
The side marker, parking, tail, license plate, instrument
panel lights, and day time running lights (P. 235) turn on.
The headlights and all the li ghts listed above (except day-
time running lights) turn on.
With the headlights on, push
the lever away from you to turn
on the high beams.
Pull the lever toward you to the
center position to turn the high
beams off.
Pull the lever toward you and
release it to flash the high
beams once.
You can flash the high beams with the headlights on or off.
1
Turning on the high beam headlights
2
3
1
2

2384-3. Operating the lights and wipers
CAMRY_U
Turn the headlight switch to the or position.
( P. 233)
Press the Automatic High
Beam switch.
When the headlight switch lever is
in the low beam position, the AHB
system will be enabled and the
AHB indicator will illuminate.
AHB (Automatic High Beam)
The Automatic High Beam uses a front camera located behind
the upper portion of the windshi eld to assess the brightness of
the lights of vehicles ahead, streetlights, etc., and automatically
turns the high beams on or off as necessary.
WARNING
■Limitations of the Automatic High Beam
Do not overly rely on the Automatic High Beam. Always drive safely, taking
care to observe your surroundings and turning the high beams on or off
manually if necessary.
■ To prevent incorrect operation of the Automatic High Beam syste m
Do not overload the vehicle.
Activating the Automatic High Beam
1
2

2394-3. Operating the lights and wipers
4
Driving
CAMRY_U■
Switching to the high beams
Push the lever away from you.
The Automatic High Beam indi-
cator will turn off and the high
beam indicator will turn on.
Pull the lever to its original posi-
tion to activate the Automatic
High Beam system again.
■
Switching to the low beams
Press the Automatic High
Beam switch.
The Automatic High Beam indi-
cator will turn off.
Press the switch to activate the
Automatic High Beam system
again.
■
Temporarily switching to the low beams
Pull the lever toward you and
then return it to its original posi-
tion.
The high beams are on while
the lever is pulled toward you.
However, after the lever is
returned to its original position,
the low beams remain on for a
certain amount of time. After-
wards, the Automatic High
Beam will be activated again.
■ Temporarily switchi ng to the low beams
It is recommended to switch to the low beams when the high beam may
cause problems or distress to other drivers or pedestrians near by.
Turning the high beams on/off manually

2404-3. Operating the lights and wipers
CAMRY_U■
Conditions to turn the high beams on/off automatically
●When all of the following conditions are met, the high beams will be turned
on automatically (after approximately 1 second):
• The vehicle speed is approximately 21 mph (34 km/h) or more.
• The area ahead of the vehicle is dark.
• There are no vehicles ahead with headlights or tail lights turned on.
• There are few streetlights on the road ahead.
● If any of the following conditions is met, the high beams will turn off automat-
ically:
• The vehicle speed is below approximately 17 mph (27 km/h).
• The area ahead of the vehicle is not dark.
• Vehicles ahead have their headlights or tail lights turned on.
• There are many streetlights on the road ahead.
■ Front camera detection information
●The high beams may not be automatically turned off in the follo wing situa-
tions:
• When a vehicle suddenly appears from around a curve
• When the vehicle is cut in front of by another vehicle
• When vehicles ahead cannot be detected due to repeated curves, road dividers or roadside trees
• When vehicles ahead appear in a faraway lane on a wide road
• When the lights of vehicles ahead are not on
● The high beams may be turned off if a vehicle ahead that is usi ng fog lights
without its headlights turned on is detected.
● House lights, street lights, traffic signals, and illuminated billboards or signs
and other reflective objects may cause the high beams to change to the low
beams, or the low beams to remain on.
● The following factors may affect the amount of time taken for t he high
beams to turn on or off:
• The brightness of the headlights, fog lights, and tail lights of vehicles
ahead
• The movement and direction of vehicles ahead
• When a vehicle ahead only has operational lights on one side
• When a vehicle ahead is a two-wheeled vehicle
• The condition of the road (gradient, curve, condition of the r oad surface,
etc.)
• The number of passengers and amount of luggage in the vehicle
● The high beams may turn on or off unexpectedly.
● Bicycles or similar vehicles may not be detected.

2414-3. Operating the lights and wipers
4
Driving
CAMRY_U●
In the following situations the system may not be able to correctly detect the
surrounding brightness level. This may cause the low beams to r emain on
or the high beams to flash or dazzle pedestrians or vehicles ah ead. In such
a case, it is necessary to manually switch between the high and low beams.
• When driving in inclement weather (heavy rain, snow, fog, sand storms,
etc.)
• When the windshield is obscured by fog, mist, ice, dirt, etc.
• When the windshield is cracked or damaged
• When the front camera is deformed or dirty
• When the temperature of the front camera is extremely high
• When the surrounding brightness level is equal to that of head lights, tail
lights or fog lights
• When headlights or tail lights of vehicles ahead are turned off, dirty,
changing color, or not aimed properly
• When the vehicle is hit by water, snow, dust, etc. from a prec eding vehi-
cle
• When driving through an area of intermittently changing brightness and darkness
• When frequently and repeatedly driving ascending/descending roads, or
roads with rough, bumpy or uneven surfaces (such as stone-paved
roads, gravel roads, etc.)
• When frequently and repeatedly taking curves or driving on a w inding
road
• When there is a highly reflective object ahead of the vehicle, such as a sign or mirror
• When the back of a preceding vehicle is highly reflective, suc h as a con-
tainer on a truck
• When the vehicle's headlights are damaged or dirty, or are not aimed
properly
• When the vehicle is listing or titling due to a flat tire, a trailer being towed,
etc.
• When the headlights are changed between the high beams and low beams repeatedly in an abnormal manner
• When the driver believes that the high beams may be flashing or dazzling pedestrians or other drivers
■ Temporarily lowering sensor sensitivity
The sensitivity of the sensor can be temporarily lowered.
Turn the engine switch off while the following conditions are m et.
• The headlight switch is in the or position.
• The headlight switch lever is in the original position.
Turn the engine switch to the “ON” position (vehicles without a smart key
system) or IGNITION ON mode (vehicles with a smart key system).
Within 60 seconds after , repeat pushing the headlight switch lever to the
high beam position then pulling it to the original position qui ckly 10 times,
then leave the lever in the original position.
1
2
32

250
CAMRY_U
4-5. Using the driving support systems
◆PCS (Pre-Collision System)
P. 2 5 8
◆LTA (Lane Tracing Assist)
P. 2 7 4
◆AHB (Automatic High Beam)
P. 2 3 8
◆RSA (Road Sign Assi st) (if equipped)
 P. 2 8 9
◆Dynamic radar cruise control with full-speed range (if
equipped)
P. 2 9 4
◆Dynamic radar cruise control (if equipped)
P. 3 1 0
Toyota Safety Sense 2.5+
The Toyota Safety Sense 2.5+ c onsists of the following drive
assist systems and contributes t o a safe and comfortable driv-
ing experience:
Driving assist system
WARNING
■ Toyota Safety Sense 2.5+
The Toyota Safety Sense 2.5+ is designed to operate under the assumption
that the driver will drive safely, and is designed to help reduce the impact to
the occupants and the vehicle in the case of a collision or assist the driver in
normal driving conditions.
As there is a limit to the degree of recognition accuracy and control perfor-
mance that this system can provide, do not overly rely on this system. The
driver is always responsible for paying attention to the vehicle's surround-
ings and driving safely.