TOYOTA LAND CRUISER 1996 J80 Workshop Manual

SS1F1−04
SS−20
−
SERVICE SPECIFICATIONS STARTING
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Starter mounting bolt3940029
Starter wire mounting nut8.89078 in.·lbf
Terminal bolt x Terminal C1717312.5
Terminal bolt x Terminal 301717312.5
End cover x Magnetic housing 1.4 kW
2.0 kW2.5
3.625
3722 in.·lbf
32 in.·lbf
End cover x Field frame 1.4 kW
2.0 kW1.5
3.815
4013 in.·lbf
35 in.·lbf
Starter hosing x Magnetic switch 1.4 kW
2.0 kW5.9
9.360
9552 in.·lbf
82 in.·lbf
Field frame x Armature assembly 1.4 kW
2.0 kW5.9
9.360
9552 in.·lbf
82 in.·lbf
Lead wire x Terminal C of starter5.96052 in.·lbf
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1F2−04
−
SERVICE SPECIFICATIONS CHARGING
SS−21
144
Author: Date:
1996 LAND CRUISER (RM451U)
CHARGING
SERVICE DATA
BatteryVoltage at 20°C (68° F)12.7 − 12.9
Drive beltTension New belt
Used belt400 − 580 N (41.0 − 59.1 kgf, 90.4 − 130.2 lbf)
200 − 390 N (20.4 − 40.0 kgf, 45.0 − 88.2 lbf)
GeneratorRated output
Rotor coil resistance at 20 °C (68° F)
Slip ring diameter STD Minimum
Brush exposed length STD
Minimum12 V 80 A
2.8 − 3.0 Ω
14.2 − 14.4 mm (0.559 − 0.567 in.)
12.8 mm (0.504 in.)
10.5 mm (0.413 in.)
1.5 mm (0.059 in.)
Voltage regulatorRegulating voltage at 25°C (77° F)
at 115 °C (239° F)14.0 − 15.1 V
13.5 − 14.3 V
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1F3−04
SS−22
−
SERVICE SPECIFICATIONS CHARGING
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Bearing retainer x Drive end frame2.62723 in.·lbf
Rectifier end frame x Drive end frame4.54640 in.·lbf
Generator pulley x Rotor11 01,12581
Rectifier x Rectifier holder2.93025 in.·lbf
Rear end cover x Rectifier holder4.44539 in.·lbf
Rectifier plate x Rectifier holder3.83934 in.·lbf
Terminal insulator x Rectifier holder4.14236 in.·lbf
Drive belt adjusting bar x Timing chain cover2121015
Generator x Generator bracket5960043
Drive belt adjusting bar x Generator2121015
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1E6−02
−
SERVICE SPECIFICATIONS AUTOMATIC TRANSMISSION
SS−23
146
Author: Date:
1996 LAND CRUISER (RM451U)
AUTOMATIC TRANSMISSION
SERVICE DATA
Line pressure (Wheel locked)
Engine idling D position R position
AT stall (Throttle valve fully opened) D position R position
422 − 481 kPa (4.3 − 4.9 kgf/cm2, 61 − 70 psi)
510 − 608 kPa (5.2 − 6.2 kgf/cm2, 74 − 88 psi)
1,285 − 1,530 kPa (13.1 − 15.6 kgf/cm2, 128 − 153 psi)
1,579 − 1,932 kPa (16.1 − 19.7 kgf/cm2, 158 − 193 psi)
Engine stall revolution D and R position1,950 ± 150 rpm
Time lag N → D position
N → R positionLess than 1.2 seconds
Less than 1.5 seconds
Engine idle speed (A/C OFF) N position650 ± 50 rpm
Throttle cable adjustment (throttle valve fully closed)
Between boot and face and inner cable stopper
0 −1 mm (0 − 0.04 in.)
Torque converter clutch installation distance
Drive plate runout Max.
Torque converter clutch runout Max.More than 15.7 mm (0.618 in.)
0.20 mm (0.0079 in.)
0.30 mm (0.0118 in.)
Shift point
D position
Throttle valve fully opened 1 → 2
2 → 3
3 → O/D
O/D → 3
3 → 2
2 → 1
2 position
Throttle valve fully opened 3 → 2
L position
Throttle valve fully opened 2 → 1
56 − 62 km/h (35 − 39 mph)
103 − 114 km/h (64 − 71 mph)
152 − 163 km/h (94 − 101 mph)
145 − 156 km/h (90 − 97 mph)
95 − 101 km/h (59 − 63 mph)
42 − 47 km/h (26 − 29 mph)
116 − 127 km/h (72 − 79 mph)
56 − 62 km/h (38 − 39 mph)
Lock−up point Throttle valve opening 5 %
D position Lock −up ON
Lock− up OFF
77 − 83 km/h (48 − 52 mph)
68 − 74 km/h (42 − 46 mph)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1E7−01
SS−24
−
SERVICE SPECIFICATIONS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Valve body x Transmission case101007
Oil stainer x Valve body101007
Oil pan7.47565 in.·lbf
Drain plug x Oil pan2020515
Parking lock pawl bracket x Transmission case7.47565 in.·lbf
Front propeller shaft x Front dif ferential7475054
Front propeller shaft x Transfer7475054
Rear propeller shaft x Transfer8890065
Rear propeller shaft x Rear dif ferential8890065
Drive plate x Crankshaft981,00072
Torque converter clutch x Drive plate5555040
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x TWC3940029
Oil cooler pipe3435025
Transmission x Engine7173053
Exhaust pipe clamp1919514
Park/neutral position switch Nut
Bolt6.9 1370
13061 in.·lbf 9
No. 2 vehicle speed sensor5.45548 in.·lbf
Speedometer driven gear sleeve x Locking plate1616012
Starter mounting bolt3940029
Transfer shift lever1818513
Stabilizer bar bracket mounting bolt1818513
Engine under cover mounting bolt2829021
Exhaust pipe No. 1 support bracket x Torque converter clutch housing2424017
Crossmember x Frame6162045
Engine rear mounting x Crossmember7475054
Transmission shift lever assembly x Body5.45548 in.·lbf
Oil cooler mounting bolt1111 58
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1E8−02
−
SERVICE SPECIFICATIONS TRANSFER
SS−25
148
Author: Date:
1996 LAND CRUISER (RM451U)
TRANSFER
SERVICE DATA
Idler gear rear bearing adjusting shim thickness Mark 2
3
4
5
6
7
8
9
10 11
12
130.30 mm (0.0118 in.)
0.45 mm (0.0177 in.)
2.40 mm (0.0945 in.)
2.60 mm (0.1024 in.)
2.80 mm (0.1102 in.)
3.00 mm (0.1181 in.)
3.20 mm (0.1260 in.)
3.40 mm (0.1339 in.)
3.60 mm (0.1417 in.)
3.80 mm (0.1496 in.)
4.00 mm (0.1575 in.)
0.55 mm (0.0216 in.)
Output shaft rear bearing adjusting shim thickness Mark B
C
DEF
G H J
K L
M N0.30 mm (0.0118 in.)
0.45 mm (0.0177 in.)
1.00 mm (0.0394 in.)
1.20 mm (0.0472 in.)
1.40 mm (0.0551 in.)
1.60 mm (0.0630 in.)
1.80 mm (0.0709 in.)
2.00 mm (0.0787 in.)
2.20 mm (0.0866 in.)
2.40 mm (0.0945 in.)
2.60 mm (0.1024 in.)
0.55 mm (0.0216 in.)
Input gear snap ring thickness Mark A
B
C
D E
F
G H J2.00 mm (0.0787 in.)
2.10 mm (0.0827 in.)
2.20 mm (0.0866 in.)
2.30 mm (0.0906 in.)
2.40 mm (0.0945 in.)
2.50 mm (0.0984 in.)
2.60 mm (0.1024 in.)
2.70 mm (0.1063 in.)
2.80 mm (0.1102 in.)
Input shaft rear ball bearing snap ring thickness Mark A
B
C
D E2.00 mm (0.0787 in.)
2.10 mm (0.0827 in.)
2.20 mm (0.0866 in.)
2.30 mm (0.0906 in.)
2.40 mm (0.0945 in.)
Idler low gear thrust clearance STD
Max.0.125 − 0.275 mm (0.0049 − 0.0108 in.)
0.275 mm (0.0108 in.)
Idler low gear radial clearance STD
Max.0.015 − 0.068 mm (0.0006 − 0.0027 in.)
0.068 mm (0.0027 in.)
High speed output gear thrust clearance STD
Max.0.10 − 0.25 mm (0.0039 − 0.0098 in.)
0.25 mm (0.0098 in.)
High speed output gear radial clearance STD
Max.0.015 − 0.071 mm (0.0006 − 0.0028 in.)
0.071 mm (0.0028 in.)
Center differential backlash Min.0.05 mm (0.0020 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS−26
−
SERVICE SPECIFICATIONS TRANSFER
149
Author: Date:
1996 LAND CRUISER (RM451U)
Center differential side gear thrust washer thickness
1.70 mm (0.0669 in.)
1.85 mm (0.0728 in.)
2.00 mm (0.0787 in.)
2.15 mm (0.0846 in.)
2.30 mm (0.0906 in.)
2.45 mm (0.0965 in.)
2.60 mm (0.1024 in.)
2.75 mm (0.1083 in.)
2.90 mm (0.1142 in.)
3.05 mm (0.1201 in.)
Front drive gear piece snap ring thickness
Mark A
B
C
D E
F
G H J
K
L2.00 mm (0.0787 in.)
2.10 mm (0.0827 in.)
2.20 mm (0.0866 in.)
2.30 mm (0.0906 in.)
2.40 mm (0.0945 in.)
2.50 mm (0.0984 in.)
2.60 mm (0.1024 in.)
2.70 mm (0.1063 in.)
2.80 mm (0.1102 in.)
1.80 mm (0.0709 in.)
1.90 mm (0.0748 in.)
Front extension housing ball bearing snap ring thickness Mark A
B1.7 mm (0.0669 in.)
1.8 mm (0.0709 in.)
Front output shaft hub snap ring thickness Mark A
B
C
D E1.8 mm (0.0709 in.)
1.9 mm (0.0748 in.)
2.0 mm (0.0787 in.)
2.1 mm (0.0827 in.)
2.2 mm (0.0866 in.)
Oil pump driven rotor body clearance STD
Max.0.08 − 0.17 mm (0.0031 − 0.0067 in.)
0.17 mm (0.0067 in.)
Oil pump driven rotor body tip clearance STD
Max.0.05 − 0.15 mm (0.0020 − 0.0059 in.)
0.15 mm (0.0059 in.)
Oil pump side clearance STD
Max.0.03 − 0.10 mm (0.0012 − 0.0039 in.)
0.10 mm (0.0039 in.)
Rear extension housing ball bearing snap ring thickness Mark A
B1.7 mm (0.0669 in.)
1.8 mm (0.0709 in.)
Rear output shaft ball bearing snap ring thickness Mark 1
2
3
41.95 mm (0.0768 in.)
2.05 mm (0.0807 in.)
2.15 mm (0.0847 in.)
2.25 mm (0.0886 in.)
Motor actuator
Terminal 2 − Terminal 3 STD resistance
Terminal 2 or 3 − Body ground STD resistance
0.3 − 100 Ω
More than 0.5 MΩ
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1E9−02
−
SERVICE SPECIFICATIONS TRANSFER
SS−27
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Oil pump plate and separator x Rear extension housing4.95043 in.·lbf
Oil pump cover x Rear extension housing4.95043 in.·lbf
Lever lock pin121209
Oil strainer x Rear case4.95043 in.·lbf
Oil receiver x Front case121209
Case cover x Rear case3738027
Rear extension housing x Rear case3738027
Front extension housing x Front case3738027
Center differential lock Indicator switch3738014
L4 position switch3738027
Neutral position switch3738027
Screw plug x Front case1919014
Screw plug x Rear extension housing2930022
Motor actuator x Front case1818513
Differential front case x Differential rear case
Temporarily tighten98
881,00090072
65
Front case x Rear case3738027
Rear case x Retainer3940028
Dynamic damper x Rear extension housing3738027
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EA−02
SS−28
−
SERVICE SPECIFICATIONS PROPELLER SHAFT
151
Author: Date:
1996 LAND CRUISER (RM451U)
PROPELLER SHAFT
SERVICE DATA
Propeller shaft runout Max.0.8 mm (0.031 in.)
Spider bearing axial playLess than 0.05 mm (0.0020 in.)
Snap ring thickness
Font propeller shaft and rear propeller shaft (Type B) Mark Color
1 −
2 −
3 −
− Brown
− Blue
6 −
7 −
8 −
Rear propeller shaft (Type A) Color
−
Brown Blue−
2.100 − 2.150 mm (0.0827 − 0.0846 in.)
2.150 − 2.200 mm (0.0846 − 0.0866 in.)
2.200 − 2.250 mm (0.0866 − 0.0886 in.)
2.250 − 2.300 mm (0.0886 − 0.0906 in.)
2.300 − 2.350 mm (0.0906 − 0.0925 in.)
2.350 − 2.400 mm (0.0925 − 0.0945 in.)
2.400 − 2.450 mm (0.0945 − 0.0965 in.)
2.450 − 2.500 mm (0.0965 − 0.0984 in.)
2.00 mm (0.0787 in.)
2.03 mm (0.0799 in.)
2.06 mm (0.0811 in.)
2.09 mm (0.0823 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EB−01
−
SERVICE SPECIFICATIONS PROPELLER SHAFT
SS−29
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Front propeller shaft x Front dif ferential7475054
Front propeller shaft x Transfer7475054
Rear propeller shaft x Rear differential8890065
Rear propeller shaft x Transfer8890065
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010