TOYOTA SEQUOIA 2001 Service Repair Manual

H16700
Adhesive
Tape
BO±50
± BODYBODY OUTSIDE MOULDING
3603 Author: Date:
2005 SEQUOIA (RM1146U)
(b) If reusing the moulding:
Clean the front door outside moulding.
(1) Using a heat light, heat the mounting to 20 ± 30 °C
(68 ± 86 °F)
NOTICE:
Do not heat the moulding excessively.
(2) Remove the adhesive tape from the moulding.
(3) Wipe off the stains with cleaner.
(4) Apply new adhesive tapes to the moulding.
(c) Install the front door outside moulding.
(1) Using a heat light, heat the front door panel and
moulding
Front door panel: 40 ± 60 °C (104 ± 140 °F)
Moulding: 20 ± 30 °C (68 ± 86 °F)
NOTICE:
Do not heat the front door and moulding.
(2) Lift the moulding release sheet from face of mould-
ing.
NOTICE:
When the moulding release sheet is removed, make sure
that no dirt or dust can get onto the uncoated area.
(3) Align the boss with the corresponding hole in front
door, and press firmly on the moulding.
6. INSTALL FRONT FENDER MOULDING
(a) Install the front fender moulding with the 5 screws.
(b) Install the front mudguard with the 3 screws.

BO46B±03
H24862
Rear Fender Wheel
Opening Moulding
Rear Mudguard

Non±reusable Part
± BODYWHEEL ARCH MOULDING
BO±51
3604 Author: Date:
2005 SEQUOIA (RM1146U)
WHEEL ARCH MOULDING
COMPONENTS

BO46C±01
H16710
Roof Drip Side Mouldingw/ Roof rack:
Front Leg CoverRear Leg Cover
Rear Leg Cover
Roof Rack Front Leg Cover
11 (115, 8)
11 (115, 8)
11 (115, 8)
11 (115, 8)
: Specified torqueN´m (kgf´cm, ft´lbf) BO±52
± BODYROOF DRIP SIDE MOULDING
3605 Author: Date:
2005 SEQUOIA (RM1146U)
ROOF DRIP SIDE MOULDING
COMPONENTS

BO46D±01
N18625
N18626
± BODYROOF DRIP SIDE MOULDING
BO±53
3606 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. w/ Roof rack:
REMOVE ROOF RACK (See page BO±173)
2. REMOVE ENDS OF ROOF DRIP SIDE MOULDING
(a) Apply protective tape to the outer surface to keep the sur-
face from being scratched.
(b) Using a heat light, heat the moulding to 20 ± 30 °C (68 ±
86 °F)
NOTICE:
Do not heat the moulding excessively.
(c) Using a scraper, pull off the roof drip side moulding from
the front and rear ends.
HINT:
Tape the scraper tip before use.
3. REMOVE ROOF DRIP SIDE MOULDING
(a) Pull off the moulding by cutting the adhesive with a knife
at the front and rear ends.
(b) Remove the moulding.
NOTICE:
Do not damage the body with the knife.

BO46E±01
H16712
Adhesive Tape
Adhesive Tape
BO±54
± BODYROOF DRIP SIDE MOULDING
3607 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
1. CLEAN CONTACT SURFACE OF BODY
(a) Using a heat light, heat the moulding surface to 40 ± 60
°C (104 ± 140°F).
NOTICE:
Do not heat the body excessively.
(b) Using a knife, cut away any rough areas on the body.
NOTICE:
Be careful not to damage the body.
(c) Wipe off stains with cleaner.
2. If reusing the moulding:
CLEAN MOULDING
(a) Using a heat light, heat the moulding surface to 20 ± 30
°C (68 ± 86°F).
NOTICE:
Do not heat the moulding excessively.
(b) Using a knife, cut the remaining adhesive from the mould-
ing.
NOTICE:
Be careful not to damage the moulding.
(c) Wipe off stains with cleaner.
(d) Apply a new adhesive tape to the moulding as shown in
the illustration.
3. COAT CONTACT SURFACE OF BODY WITH PRIMER
ºMº
Using a brush, coat the contact surface on the body with Primer
M as shown in the illustration.
NOTICE:

Allow 3 minutes or more to dry the primer coated sur-
face.

Do not coat the adhesive.

H16711
Windshield Glass
Primer M
Apply Primer M on
panel in this rangeApply Primer M on
panel in this rangePrimer M
H16713
Windshield GlassAdhesive
20 mm
(0.79 in.)
6 mm (0.24 in.)Adhesive
20 mm
(0.79 in.)
± BODYROOF DRIP SIDE MOULDING
BO±55
3608 Author: Date:
2005 SEQUOIA (RM1146U)

Do not keep any of the opened Primer M for later use.
4. APPLY ADHESIVE
(a) Cut off the tip of cartridge nozzle.
Part No. 08850±00801 or equivalent.
HINT:
After cutting off the tip, use all adhesive within the time de-
scribed in the table below.
TemperatureTackfree time
35 °C (95 °F)15 minutes
20 °C (68 °F)100 minutes
5 °C (41 °F)8 minutes
(b) Load the cartridge into the sealer gun.
(c) Apply adhesive to the hatched area in the illustration for
both front and rear of the vehicle.
5. INSTALL ROOF DRIP SIDE MOULDING
(a) Using a heat light, heat the moulding to 20 ± 30 °C (68 ±
86 °F)
NOTICE:
Do not heat the moulding excessively.

BO±56
± BODYROOF DRIP SIDE MOULDING
3609 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Lift the moulding release sheet from the face of moulding.
NOTICE:
When the moulding release sheet is removed, make sure
that no dirt or dust can get onto the coated area.
(c) Install the moulding.
NOTICE:

Make sure that the body and moulding are heated to
a proper temperature.

Do not depress the adhesive coated parts excessive-
ly but just hold them down with your thumb.

Scrape off any overflowing adhesive with a plastic
spatula and clean the surface with a dry rag.

Take care not to drive the vehicle during the time de-
scribed in the table below.
TemperatureMinimum time prior to driving the vehicle
35 °C (95 °F)1.5 hours
20 °C (68 °F)5 hours
5°C (41° F)24 hours
6. w/ Roof rack:
INSTALL ROOF RACK (See page BO±173)
Torque: 11 N´m (115kgf´cm, 8 ft´lbf)

BO46F±01
H16706
Roof Side Rail Weatherstrip
Center Pillar Upper
End Weatherstrip
± BODYROOF DRIP SIDE FINISH MOULDING
BO±57
3610 Author: Date:
2005 SEQUOIA (RM1146U)
ROOF DRIP SIDE FINISH MOULDING
COMPONENTS

H16707
BO46G±01
H16708
H16709
BO±58
± BODYROOF DRIP SIDE FINISH MOULDING
3611 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE CENTER PILLAR UPPER END WEATH-
ERSTRIP
Using a screwdriver, remove the weatherstrip.
HINT:
Tape the screwdriver tip before use.
2. REMOVE ROOF SIDE RAIL WEATHERSTRIP
Using SST, pull off the roof side rail weatherstrip from end.
SST 09806±30010
HINT:
At the time of installation, please refer to the following item.
Attach the upper edge of the weatherstrip to body flange. Tap
on the weatherstrip by hand.

BO46H±01
± BODYROOF DRIP SIDE FINISH MOULDING
BO±59
3612 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page BO±58).