TOYOTA T100 1996 Factory Service Manual

Downloaded from www.Manualslib.com manuals search engine SA0HP−01
R04508
− SUSPENSION AND AXLEFRONT LOWER BALL JOINT (4WD)
SA−121
1996 TOYOTA T100 (RM449U)
INSPECTION
INSPECT LOWER BALL JOINT FOR ROTATION CONDI-
TION
(a) As shown in the illustration, flip the ball joint stud back and
forth 5 times, before installing the nut.
(b) Using a torque wrench, turn the nut continuously one turn
each 2 − 4 seconds and take the torque reading on the 5th
turn.
Turning torque :
2.0 − 3.9 N·m (20 − 40 kgf·cm, 17 − 34 in.·lbf)

Downloaded from www.Manualslib.com manuals search engine SA0HQ−01
SA−122
− SUSPENSION AND AXLEFRONT LOWER BALL JOINT (4WD)
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−120).
AFTER INSTALLATION, CHECK ABS SPEED SENSOR SIGNAL (See page DI−321) AND FRONT
WHEEL ALIGNMENT (See page SA−10)

Downloaded from www.Manualslib.com manuals search engine SA0HR−07
− SUSPENSION AND AXLEFRONT STABILIZER BAR (2WD)
SA−123
1562 Author: Date:
1996 TOYOTA T100 (RM449U)
FRONT STABILIZER BAR (2WD)
COMPONENTS

Downloaded from www.Manualslib.com manuals search engine SA0HS−01
R04505
R05271
SA−124
− SUSPENSION AND AXLEFRONT STABILIZER BAR (2WD)
1996 TOYOTA T100 (RM449U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
2. REMOVE STABILIZER BAR
(a) Remove the nut, 3 retainers, 2 cushions and stabilizer bar
from the lower suspension arm.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(b) Remove the nut, 2 cushions, 2 retainers and disconnect
the stabilizer bar.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(c) Employ the same manner described above to the other
side.
(d) Remove the 4 bolts, stabilizer bar brackets, bushings and
remove the stabilizer bar.
Torque: 30 N·m (306 kgf·cm, 22 ft·lbf)

Downloaded from www.Manualslib.com manuals search engine SA0HT−01
− SUSPENSION AND AXLEFRONT STABILIZER BAR (2WD)
SA−125
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−124).

Downloaded from www.Manualslib.com manuals search engine SA0HU−02
SA−126
− SUSPENSION AND AXLEFRONT STABILIZER BAR (4WD)
1565 Author: Date:
1996 TOYOTA T100 (RM449U)
FRONT STABILIZER BAR (4WD)
COMPONENTS

Downloaded from www.Manualslib.com manuals search engine SA0HV−01
FA1722
R05271
− SUSPENSION AND AXLEFRONT STABILIZER BAR (4WD)
SA−127
1996 TOYOTA T100 (RM449U)
REMOVAL
REMOVE STABILIZER BAR
(a) Remove the nut, 4 cushions, 5 retainers, collar and stabi-
lizer bar from the lower suspension arms.
Torque: 25 N·m (260 kgf·cm, 19 ft·lbf)
(b) Employ the same manner described above to the other
side.
(c) Remove the 4 bolts, 2 stabilizer bar brackets, 2 cushions
and remove the stabilizer bar.
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)

Downloaded from www.Manualslib.com manuals search engine SA0HW−01
SA−128
− SUSPENSION AND AXLEFRONT STABILIZER BAR (4WD)
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−127).

Downloaded from www.Manualslib.com manuals search engine SA0HX−03
− SUSPENSION AND AXLEREAR AXLE SHAFT
SA−129
1568 Author: Date:
1996 TOYOTA T100 (RM449U)
REAR AXLE SHAFT
COMPONENTS

Downloaded from www.Manualslib.com manuals search engine SA−130
− SUSPENSION AND AXLEREAR AXLE SHAFT
1569 Author: Date:
1996 TOYOTA T100 (RM449U)