VOLVO XC90 TWIN ENGINE HYBRID 2017 Owners Manual

MAINTENANCE AND SERVICING
* Option/accessory, for more information, see Introduction.529

Positions
•Fuses 13–17 and 21–36 are called "Micro".
•Fuses 1–12, 18–20 and 37 are called"MCase" and should only be replaced by atrained and qualified Volvo service technician.
FunctionA
Heated rear window30
Power rear seat (driver side)A20A
Pneumatic suspension* compres-sor40
Rear electric heater (passengerside)30
––
Rear electric heater (driver side)30
Power rear seat (passenger side)A20A
––
Power tailgate*25
Power front seat (passenger side)*module20
Trailer hitch* control module40
Seat belt tensioner module (pas-senger side)40
FunctionA
Internal relay windings5
––
Foot movement detection modulefor opening the power tailgate*5
––
Module for electrically folding thirdrow seats*20
Trailer hitch* control module25
Power front seat (driver seat*module20
Seat belt tensioner module (driverside)40
Parking camera*5
––
––
Ionic air cleanerA5A
Feed when ignition is switched on.10
Airbag and seat belt tensionermodules5
FunctionA
Cooler; heated/cooled cup holder
(rear)A10A
Heated rear seat (driver side)*15
––
Blind Spot Information (BLIS)*5
––
Seat belt tensioner modules5
Emission system actuator5
––
––
Heated rear seat (passengerside)*15
––
AXC90 Excellence.

Related information
•Replacing fuses (p. 517)
•Fuses (p. 516)
•Fuses in the passenger compartment(p. 523)
•Fuses in the engine compartment (p. 518)

MAINTENANCE AND SERVICING
530
Replacing bulbs
The halogen headlight bulbs3 can be replacedby the owner.
Before the halogen headlight bulbs can bereplaced, that plastic covering over the headlighthousing has to be removed.

NOTE
Halogen headlights are not available on allmodels or in all markets.
Consult your Volvo retailer if you are uncertainabout the type of headlights in your vehicle.
To do so:
Lift the rubber strip by pressing in toward theengine compartment.
Release the pins in the plastic covering'sfour clips by pressing them down with ascrewdriver or similar object and remove thecovering.
The turn signal, high/low beam, Daytime RunningLight and parking light bulbs will be accessiblewhen the plastic covering has been removed.
Put the covering back in place in the reverseorder.
NOTE
The pins in the clips have to be pressed backcompletely before the clips are placed in theplastic covering.
When the covering is put back in place, thepins must be pressed so that their upper sur-face is flush with the surface of the clip.
3Halogen headlights are not available on all models.

MAINTENANCE AND SERVICING
}}
531

NOTE
•For information regarding any bulbs notmentioned in this section, please contactyour Volvo retailer or a trained andauthorized Volvo service technician.
•Always switch off the ignition before star-ting to replace a bulb.
•If an error message remains in the dis-play after a faulty bulb has been replaced,contact an authorized Volvo workshop.
•Condensation may form temporarily onthe inside of the lenses of exterior lightssuch as headlights, fog lights, or taillights.This is normal and the lights aredesigned to withstand moisture. Normally,condensation will dissipate after thelights have been on for a short time.
•The optional Active Bending Light bulbscontain trace amounts of mercury. Thesebulbs should always be disposed of by atrained and qualified Volvo service techni-cian.
CAUTION
Never touch the glass of bulbs with your fin-gers. Grease and oils from your fingers vapor-ize in the heat and will leave a deposit on thereflector, which will damage it.

WARNING
•The ignition should be switched off com-pletely (be in ignition mode 0) whenreplacing bulbs.
•If the engine has been running just priorto replacing bulbs in the headlight hous-ing, please keep in mind that componentsin the engine compartment will be hot.
Front bulbs (vehicles with halogen
headlights)
Low beam
High beam
Parking light/Daytime Running Light
Turn signal
(Not in use)

||
MAINTENANCE AND SERVICING
532

Taillight bulbs
Brake light (LED)
Side marker light (LED)
Backup light4
Taillight (LED)
Turn signal (LED)
Fog light (LED)
High-mounted brake light (LED)

Related information
•Bulb specifications (p. 536)
•Removing the rectangular headlight cover(p. 532)
•Replacing parking light bulbs (p. 534)
•Replacing front turn signal bulbs (p. 535)
•Replacing High Beam headlight bulbs(p. 534)
•Replacing low beam headlight bulbs(p. 533)
Removing the rectangular headlightcover
Most of the bulbs in the headlight housing canbe accessed when the rectangular cover hasbeen removed.
Before the rectangular cover can be removed, theplastic covering must be removed, see the article"Replacing bulbs" for information.
1. Loosen the cover's four screws with a T20Torx screwdriver (1) but do not remove themcompletely (turning them 3–4 turns isenough).
2.Push the cover to the side.
3. Remove the cover.
Put the cover back in place in the reverse order.
4Must be replaced by a trained and qualified Volvo service technician.

MAINTENANCE AND SERVICING
533

Related information
•Replacing bulbs (p. 530)Replacing low beam headlight bulbs
On models with halogen headlights, the lowbeam headlight bulb can be replaced by theowner.
Before the bulb can be replaced, the plastic cov-ering over the headlight housing has to beremoved, see the article "Replacing bulbs."

CAUTION
Never touch the glass of bulbs with your fin-gers. Grease and oils from your fingers vapor-ize in the heat and will leave a deposit on thereflector, which will damage it.
Driver's side bulb housing shown
1. Remove the low beam round rubber coverfrom the headlight housing.
2.Remove the connector from the bulb.
3. Remove the bulb by pressing it slightlyupward and then pulling it out.
4. Insert the bulb in the socket. The bulb's guid-ing pin should point straight up.
5. Press the connector into place.
6. Put the rubber cover back into place.
Related information
•Replacing bulbs (p. 530)
•Bulb specifications (p. 536)

MAINTENANCE AND SERVICING
534
Replacing High Beam headlightbulbs
On models with halogen headlights, the HighBeam headlight bulb can be replaced by theowner.
Before the bulb can be accessed, the headlighthousing's rectangular cover must be removed,see the article "Removing the rectangular head-light cover."

CAUTION
Never touch the glass of bulbs with your fin-gers. Grease and oils from your fingers vapor-ize in the heat and will leave a deposit on thereflector, which will damage it.
Driver's side bulb housing shown
1. Remove the bulb by turning the bulb holderupward and then pulling it straight out.
2.Carefully pry the plastic sleeve by the con-nector's locking lug to release it.
3. Remove the connector from the bulb.
4. Insert a new bulb.
5. Insert the bulb in the socket and turn itdownward.

Related information
•Removing the rectangular headlight cover(p. 532)
•Bulb specifications (p. 536)
•Replacing bulbs (p. 530)
Replacing parking light bulbs
On models with halogen headlights, the frontparking light bulb can be replaced by the owner.
Before the bulb can be accessed, the headlighthousing's rectangular cover must be removed,see the article "Removing the rectangular head-light cover."
Remove the high beam bulb first by turning thebulb holder upward and then pulling it straightout. This makes it easier to access the parkinglight bulb.
Driver's side bulb housing shown
1. Pull the bulb holder straight out.
2.Remove the bulb by pulling it straight out.
3. Insert a new bulb.
4. Insert the bulb holder in the socket andpress it into place.

MAINTENANCE AND SERVICING
535
5. If the high beam bulb was removed, insertthe bulb in the socket and turn downward.

Related information
•Replacing bulbs (p. 530)
•Bulb specifications (p. 536)
•Removing the rectangular headlight cover(p. 532)
Replacing front turn signal bulbs
On models with halogen headlights, the frontturn signal bulb can be replaced by the owner.
Before the bulb can be accessed, the headlighthousing's rectangular cover must be removed,see the article "Removing the rectangular head-light cover".
Driver's side headlight housing shown
1. Press the retaining catches together and pullthe bulb holder straight out.
2.The bulb holder and bulb must be replacedas one unit.
3. Press the new bulb holder into the socket.

Related information
•Removing the rectangular headlight cover(p. 532)
•Replacing bulbs (p. 530)
•Bulb specifications (p. 536)

MAINTENANCE AND SERVICING
536
Bulb specifications
The following specifications apply to models
equipped with halogen5 headlights. If otherbulbs need to be replaced, contact a trainedand qualified Volvo service technician.
Function[W]AType
Low beam55H11
High Beam65H9
Front turn signal24PY24W
Daytime running light/parking light21/5W21/5W
AWatt

Related information
•Replacing bulbs (p. 530)
5Halogen headlights are not available on all models.

MAINTENANCE AND SERVICING
}}
* Option/accessory, for more information, see Introduction.537
Hoisting the vehicle
When the vehicle is hoisted, the jack or garagelift must be positioned correctly under the vehi-cle.
For vehicles equipped with leveling control*, if it isalso equipped with the optional pneumatic sus-pension, this must be deactivated before thevehicle is hoisted. This is done from the centerdisplay:
1.Tap Settings in Top view.
2.Tap My CarSuspension .
3.Select Deactivate Suspension & LevelingControl.

||
MAINTENANCE AND SERVICING
538
Location of the jack attachment points (triangles)/lifting points (red areas)

NOTE
The jack provided with your vehicle isintended to be used only in temporary situa-tions such as changing wheels in the event ofa flat tire. Only the jack that came with yourparticular model should be used to lift thevehicle. If the vehicle needs to be lifted morefrequently or for a prolonged period, using agarage jack or hoist is recommended. Alwaysfollow this device