stop start YAMAHA TMAX 2021 Owners Manual

Smart key system
3-8
3
If the steering continues to be
locked and will not release, the
smart key system indicator light
will flash slowly. Move the handle-
bar gently to the left and right to
help release the steering lock and
then press the “ON/ ” switch
again.
 The smart key system indicator
light will flash if the centerstand
lock cannot automatically release
itself. Gently rock the vehicle for-
ward or backward and then press
the “ON/ ” switch one more
time.
 If the centerstand continues to be
locked and will not release, the
smart key system indicator light
will flash slowly. Rock the vehicle
forward and backward to help re-
lease the centerstand lock and
then press the “ON/ ” switch
again.
NOTICE
ECA15826
If the steerin g lock or centerstan d
lock will not release an d the smart
key system in dicator li ght is flash-
in g, have a Yamaha d ealer check the
smart key system.3. The power of the vehicle is turned on when all locks have been re-
leased. The multi-function display
will come on.
4. The engine can now be started. (See page 7-2.)TIPSee page 8-39 for information about
emergency mode and how to turn the
vehicle power on without the smart
key.
EAU78033
Powerin g off the vehicleTo turn the vehicle power off and stop
the engine if it is running, press the
“OFF/LOCK” switch.
Upon authentification of the smart key,
the beeper will sound once to confirm
that the vehicle power has been suc-
cessfully turned off and the storage
compartment and fuel tank cap lid
locks will be released.TIP The rider must turn off the power
of the vehicle manually.
 The power of the vehicle will not
turn off automatically even if the
smart key is moved out of operat-
ing range of the smart key system.1. “OFF/LOCK” switch
1
UB3TE1E0.book Page 8 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-2
5
EAU77450
En gine stop switch “ / ”
Set this switch to “ ” before starting
the engine. Set this switch to “ ” to
stop the engine in case of an emergen-
cy, such as when the vehicle overturns
or when the throttle cable is stuck.
EAU77291
Power on/Starter switch “ON/ ”
With the smart key turned on and with-
in range, press this switch to turn on
the power to the vehicle. Then with the
sidestand up and while applying the
front or rear brake, push this switch to
crank the engine with the starter. See
page 7-2 for starting instructions prior
to starting the engine.
EAU79601
Hazar d switch “ ”
With the vehicle power is on or in park-
ing mode, use this switch to turn on the
hazard lights (simultaneous flashing of
all turn signal lights).
The hazard lights are used in case of an
emergency or to warn other drivers
when your vehicle is stopped where it
might be a traffic hazard.
NOTICE
ECA10062
Do not use the hazar d lig hts for an
exten ded len gth of time with the en-
g ine not runnin g, otherwise the bat-
tery may d ischarge.
EAU73952
Cruise control switches
See page 4-1 for an explanation of the
cruise control system.
EAU77301
Menu switch “MENU”
This switch is used to make setting
changes within the multi-function dis-
play. (See page 5-5.)
EAU77311
Select switch “ / ”
This switch is used to make setting
changes within the multi-function dis-
play. (See page 5-5.)
EAU73931
Drive mo de switch “MODE”
See page 4-3 for an explanation of the
drive mode.
EAU77123
In dicator li ghts an d warnin g
lig hts
EAU88680
Turn si gnal in dicator li ghts “ ”
an d“”
Each indicator light will flash when its
corresponding turn signal lights are
flashing.1. High beam indicator light “ ”
2. Traction control system indicator light “ ”
3. Turn signal indicator lights “ ” and “ ”
4. Smart key system indicator light “ ”
5. ABS warning light “ ”
6. Malfunction indicator light “ ”
7. Cruise control indicator lights
1 2 4 5 6
3
7
12
45 6
3
7
UB3TE1E0.book Page 2 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-6
5
Fuel meter
The fuel meter indicates the amount of
fuel in the fuel tank. The display seg-
ments of the fuel meter disappear from
“F” (full) towards “E” (empty) as the fuel
level decreases. When the last seg-
ment starts flashing, refuel as soon as
possible.
TIPIf a problem is detected in the fuel me-
ter electrical circuit, the fuel meter will
flash repeatedly. Have a Yamaha deal-
er check the vehicle.
Coolant temperature meter
The coolant temperature varies with
changes in the weather and engine
load. If the top segment starts flashing,
the information display automatically
changes to “C-TEMP” and “Hi” flash-
es. Stop the vehicle and let the engine
cool. (See page 8-38.)TIPThe information display cannot be
changed while the engine is overheat-
ing.NOTICE
ECA10022
Do not continue to operate the en-
g
ine if it is overheatin g.
Eco in dicator
This indicator comes on when the vehi-
cle is being operated in an environ-
mentally friendly, fuel-efficient manner.
The indicator goes off when the vehicle
is stopped.TIPConsider the following tips to reduce
fuel consumption:  Avoid high engine speeds during
acceleration.
 Travel at a constant speed.
1. Fuel meter
1
1. Coolant temperature meter
1
1.
1
UB3TE1E0.book Page 6 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-9
5 
If the am bient temperature is 20
°C (68 °F) or hi gher, do not set
the seat heater to the hi gh set-
ting .
 If the seat b ecomes worn or
d amag ed , stop usin g the seat
heater an d replace the seat.
Changing the information displayThe information display items are
grouped into 3 display pages.
Push the “ ” or “ ” side of the se-
lect switch to rotate among the 3 dis-
play pages.TIPThe items for each display page can be
customized. (See page 5-14.)
Odometer:The odometer shows the total distance
traveled by the vehicle.
Tripmeters:
tance traveled since they were last set
to zero.
To reset a tripmeter, use the select
switch to select the information display
page that contains the tripmeter you
want to reset. Push the Ž side of
the select switch for one second so
that the tripmeter flashes, and then push the Ž side of the select switch
again for one second while the tripme-
ter is flashing.
TIP
The odometer will lock at 999999.
 The tripmeters will reset and con-
tinue counting after 9999.9 is
reached.When approximately 3.0 L (0.79 US
gal, 0.66 Imp.gal) of fuel remains in the
fuel tank, the last segment of the fuel
meter starts flashing. In addition, the
information display will automatically
change to the fuel reserve tripmeter
mode “F-TRIP” and start counting the
distance traveled from that point.
In this case, push the select switch to
switch the display in the following or-
der:
F-TRIP Display–1 Display–2
Display–3 F-TRIP
UB3TE1E0.book Page 9 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-29
5
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is turned on.
3. Turn the vehicle power on.
4. Keep the front or rear br ake applied.
5. Push the “ON/ ” switch.
Does the engine start?
With the engine still off:
6. Move the sidestand up.
7. Keep the front or rear br ake applied.
8. Push the “ON/ ” switch.
Does the engine start?
With the engine still running:
9. Move the sidestand down.
Does the engine stall?
The system is OK. The scooter can be ridden. The sidestand switch may not be working correctly.
The scooter should not be ridden
until
checked by a Y amaha dealer.
The sidestand switch may not be working correctly.
The scooter should not be ridden until
checked by a Y amaha dealer.
YES NO YES NO NO YES
The brake switch may not be working correctly.
The scooter should not be ridden until
checked by a Y amaha dealer.The vehicle must be placed on the center-
stand during this inspection. If a malfunction is noted, have a Yamaha
dealer check the system before riding.
WARNING
UB3TE1E0.book Page 29 Friday, September 11, 2020 8:48 AM

Operation and important rid ing points
7-2
7
EAU88770
Startin g the eng ineThe ignition circuit cut-off system will
enable starting when the sidestand is
up.
To start the engine1. With the smart key turned on, ap-
proach the vehicle.
2. Push the “ON/ ” switch and set the engine stop switch to the run
position.
Upon authentication of the smart
key, the beeper will sound twice
and the centerstand and steering
locks (if applied) will be released.
3. Confirm the indicator and warning light(s) come on for a few sec-
onds, and the go off. (See page
5-2.)TIPDo not start the engine if the mal-
function indicator light remains on.
 The ABS warning light should
come on and stay on until the ve-
hicle reaches a speed of 10 km/h
(6 mi/h).
NOTICE
ECA24110
If a warnin g or in dicator li ght does
not work as d escribed a bove, have a
Yamaha dealer check the vehicle.4. Close the throttle completely.
5. While applying the front or rear
brake, push the “ON/ ” switch.
6. Release the “ON/ ” switch when the engine starts, or after 5 sec-
onds. Wait 10 seconds before
pressing the switch again to allow
battery voltage to restore.NOTICE
ECA11043
For maximum en gine life, never ac-
celerate har d when the en gine is
col d!
EAU88780
TIPThis model is equipped with:
 a lean angle sensor. This sensor
stops the engine in case of a vehi-
cle turnover. If this happens, the
malfunction indicator light will
come on, but this is not a malfunc-
tion. Turn the vehicle power off
and then back on again to cancel
the indicator light. Failing to do so
will prevent the engine from start-
ing even though the engine will
crank when pushing the start
switch.
 an engine auto-stop system. The
engine stops automatically if left
idling for 20 minutes. If the engine
stops, simply push the start
switch to restart the engine.
UB3TE1E0.book Page 2 Friday, September 11, 2020 8:48 AM

Periodic maintenance an d a djustment
8-38
8
EAU86420
En gine overheatin g
WARNING
EWAT1041
Do not remove the ra diator cap when the en gine an d ra diator are hot. Scal din g hot flui d an d steam may be
b lown out un der pressure, which coul d cause serious injury. Be sure to wait until the en gine has coole d.
 Place a thick rag , like a towel, over the ra diator cap, an d then slowly rotate the cap counterclockwise to the
d etent to allow any resi dual pressure to escape. When the hissin g soun d has stopped , press down on the cap
while turnin g it counterclockwise, an d then remove the cap.TIPIf coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended cool-
ant as soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
UB3TE1E0.book Page 38 Friday, September 11, 2020 8:48 AM

Periodic maintenance an d a djustment
8-39
8
EAU77373
Emer gency mo deWhen the smart key is lost, damaged,
or its battery has discharged, the vehi-
cle can still be turned on and the en-
gine started. You will need a
mechanical key and the smart key sys-
tem identification number. To operate
the vehicle in emergency mode, carry
out the following steps.TIPEmergency mode operation will be
cancelled if the respective steps are
not carried out within the time set for

switch is pushed.1. Stop the vehicle in a safe place.
2. Unlock the seat by inserting the
mechanical key into the lock lo-
cated right side of body and turn it
counter clockwise. 3. Open the seat and check that the
trunk light comes on.
4. Ž switch once.
5. Without completely shutting the seat, raise and lower it three times
within 10 seconds.
TIPUse the rear storage compartment
light as a guide when raising and low-
ering the seat.
The smart key system indicator
light on the speedometer will
come on for three seconds to indi-
cate the transition to emergency
mode. 6. After the smart key system indica-
tor light goes off, use the / Ž
switch to enter the identification
number.
1. Smart key system indicator light Ž
1. Identification number
1 1
123456
1
UB3TE1E0.book Page 39 Friday, September 11, 2020 8:48 AM

12-1
12
Index
AABS warning light ................................... 5-3
Acceleration and deceleration ................ 7-3
Air filter element and check hose,
replacing and cleaning ....................... 8-17
Air filter element, V-belt ........................ 8-18
Anti-lock brake system (ABS)............... 5-19
Auxiliary DC jack .................................. 5-26BBattery .................................................. 8-30
Brake fluid, changing............................ 8-26
Brake fluid level, checking.................... 8-25
Brake lever, front .................................. 5-17
Brake lever, rear ................................... 5-18
Brake levers, lubricating ....................... 8-28
Braking ................................................... 7-3CCables, checking and lubricating ......... 8-27
Canister ................................................ 8-12
Care ........................................................ 9-1
Catalytic converter ............................... 5-22
Centerstand and sidestand, checking and lubricating ................................... 8-28
Coolant ................................................. 8-15
Cruise control indicator lights................. 5-3
Cruise control switches .......................... 5-2
Cruise control system............................. 4-1DData recording, vehicle......................... 11-2
Diagnostic connector ........................... 11-2
Dimmer/Pass switch............................... 5-1
D-mode (drive mode).............................. 4-3
Drive belt .............................................. 8-26
Drive mode switch .................................. 5-2
EEmergency mode ................................. 8-39
Engine break-in ...................................... 7-1
Engine idling speed, checking ............. 8-18
Engine oil and oil filter cartridge........... 8-12
Engine overheating .............................. 8-38
Engine serial number ........................... 11-1
Engine stop switch................................. 5-2FFront and rear brake lever free play, checking ............................................ 8-22
Front and rear brake pads, checking ... 8-24
Front fork, checking ............................. 8-29
Fuel ...................................................... 5-20
Fuel consumption, tips for reducing ...... 7-4
Fuel tank cap........................................ 5-20
Fuel tank overflow hose ....................... 5-22
Fuses, replacing ................................... 8-32HHandlebar switches ............................... 5-1
Hazard switch ........................................ 5-2
High beam indicator light ....................... 5-3
Horn switch ............................................ 5-1
How to lock the centerstand ................ 3-10
How to lock the steering ........................ 3-9IIdentification numbers ......................... 11-1
Ignition circuit cut-off system .............. 5-28
Indicator lights and warning lights ......... 5-2KKey, handling of smart and mechanical key ....................................................... 3-3LLicense plate light bulb, replacing ....... 8-34
MMaintenance and lubrication, periodic ... 8-5
Maintenance, emission control system .................................................. 8-3
Malfunction indicator light (MIL) ............. 5-3
Matte color, caution................................ 9-1
Menu switch ........................................... 5-2
Model label ........................................... 11-1
Multi-function display ............................. 5-5OOperating range of the smart key system .................................................. 3-2PPanels, removing and installing .............. 8-9
Parking.................................................... 7-4
Parking mode ....................................... 3-13
Part locations.......................................... 2-1
Powering off the vehicle ......................... 3-8
Powering on the vehicle ......................... 3-7
Power on/Starter switch ......................... 5-2RRear brake lock cable, adjusting .......... 8-23
Rear brake lock, checking .................... 8-23
Rear brake lock lever ............................ 5-18
Rear view mirrors .................................. 5-24SSafe-riding points ................................... 1-5
Safety information................................... 1-1
Select switch .......................................... 5-2
Shock absorber assembly .................... 5-25
Sidestand.............................................. 5-27
Smart key................................................ 3-5
Smart key battery, replacing................... 3-6
Smart key system ................................... 3-1
UB3TE1E0.book Page 1 Friday, September 11, 2020 8:48 AM