CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

Page 191 of 659


SECTION
4

REAR SUSPENSION
AND
DRIVE LINE

CONTENTS
OF
THIS SECTION

Page

Rear Suspension
4-1

Drive Line.
. 4-26

Rear Axle ......
4-26
Propeller Shaft
and
Universal Joints

Special Tools
4-37

4-43

REAR SUSPENSION

INDEX

General Description
4-1

Chevrolet
4-1

Chevelle
4-1

Chevy
n and
Camaro
. . . . . 4-2

Corvette
. . . . . . 4-3

Maintenance
and
Adjustments ...............
4-4

Riding Height Check (Chevrolet, Camaro,

Chevelle
and
Chevy
II) 4-5

Wheel Alignment (Corvette)
4-5

Wheel Bearing Adjustment (Corvette)
4-6

Component Parts Replacement (Chevrolet, Camaro,

Chevelle
and
Chevy
JJ) 4-7

Coil Spring
4-7

Chevrolet
4-7

Removal
4-7

Installation
4-7

Chevelle
4-8

Removal
4-8

4-8

Installation
.

Leaf Spring, Spring Seat Pads, Spring
Eye

Bushings
4-9

Chevy
H 4-9

Removal
4-9

Installation
4-9

Camaro
4-10

Removal
4-10

Installation
4-11

Shock Absorber
4-11

Chevrolet
and
Chevelle
. 4-11

Removal
4-11

Installation
. . 4-12

Chevy
II 4-12

Removal
4-12

Installation
4-rl2

Camaro
4-12

Removal
. 4-12

Installation
4-12

Control
Arm . . 4-12

Chevrolet Upper
4-12

Removal
. 4-12
Page

Bushing Replacement
. 4-13

Installation
4-14

Chevrolet Lower
4-14

Removal
4-14

Bushing Replacement
4-14

Installation
. 4-15

Chevelle Upper
and
Lower.
. 4-15

Removal
4-15

Bushing Replacement
4-15

Installation
4-17

Rear Suspension
Tie Rod
(Chevrolet)
. . .
......
. . . 4-17

Removal
4-17

Bushing Replacement
4-17

Installation
4-17

Component Parts Replacement (Corvette)
. . 4-17

Wheel Spindle
and
Support
4-17

Removal
4-17

Repairs
', . 4-17

Installation
4-18

Differential Carrier Support Bracket Replacement.
. 4-20

Shock Absorber
4-20

Removal
4-20

Installation
* .... 4-20

Strut
Rod and
Bracket
4-20

Removal
4-20

Repairs
4-21

Installation
4-21

Spring
4-21

Removal
4-21

Repairs
4-22

Installation
4-22

Torque Control
Arm 4-23

Removal
4-23

Repairs
. 4-23

Installation
4-24

Suspension Crossmember
4-24

Removal
4-24

Repairs—Isolation Mount
4-25

Installation
4-25

Stabilizer Shaft Replacement
4-25

GENERAL DESCRIPTION

CHEVROLET

The link type rear suspension (fig. 1) has two lower

control arms which maintain proper axle to frame re-

lationship and also take the acceleration, drive and

braking forces. A single upper control arm on light-

duty models (or two upper control arms on heavy-duty

models and all station wagons) limits axle rotation when

drive, acceleration or braking forces are applied. Lateral

movement of the axle is restricted by the axle-to-frame

tie rod. Two full coil springs and two direct, double
acting shock absorbers are provided for additional ride

control.

CHEVELLE

The rear suspension (fig. 2) is of the four-link design

utilizing axle mounted, full coil springs and direct,

double-acting shock absorbers.

Two rubber-bushed lower control arms, stretching

slightly outboard from axle-mounted brackets to frame

side member mounted brackets, maintain fore and aft

CHEVROLET CHASSIS SERVICE MANUAL

Page 192 of 659


REAR SUSPENSION AND DRIVE LINE 4-2

SHOCK ABSORBER

UPPER ATTACHMENT

COIL SPRING

\

R.H. UPPER

CONTROL ARM

LH.
UPPER

CONTROL ARM

(HEAVY DUTY AND

STATION WAGON)
TIE ROD

ATTACHMENT

SHOCK ABSORBER

LOWER ATTACHMENT

LOWER

CONTROL ARM

Fig.
1—Chevrolet Rear Suspension Components

relationship of the axle assembly to the vehicle proper.

These lower control arm axle brackets also mount the

axle rebound bumpers and provide for lower attachment

of the shock absorber. Upper attachment of the shock

absorber is a platform mount to the rear of the coil

spring frame bracket. The coil springs are pigtailed

at both ends; the upper end is isolated from the frame

seat by a rubber insulator, while the lower end seats

on the axle mounted spring bracket which has a vertical

flange to retain the spring.

Sideways movement of the axle assembly is controlled

by two angularly mounted, rubber-bushed upper control

arms.
Projecting ears, cast as part of the differential
carrier, provide for rear attachment and frame cross-

member mounted brackets retain them at the forward

end.

CHEVY 11 AND CAMARO

The.Chevy n and Camaro rear suspension (fig. 3 and

fig.
4) consists of two uniformly stressed rear springs

and two shock absorbers mounted to the spring lower

seats.
The
.
springs are rubber mounted at both axle

and frame attaching points, thus insuring uniform spring

loading, minimizing transmittal of road vibration to

passenger compartment, and providing a pivot point to

•MMMi
MMM—Hi—1—1——1——1MMMMiM_

[•?{aw-i
'
"'
i

\ SHOCK^^BBB^^B(^^CO1L

ABSORBER ^HH^ SPRING
g^8^"
_ LOWER

feSfcto^
CONTROL
ARM

Fig.
2—Chevelle Rear Suspension Components

CHEVROLET CHASSIS SERVICE MANUAL

Page 193 of 659


REAR SUSPENSION
AND
DRIVE LINE
4-3

AXLE ASSEMBLY
LEAF SPRING

SPRING REAR SHACKLE

SHOCK ABSORBER

Fig.
3—Chevy
II
Rear Suspension Components

absorb axle "wind-up.
The
springs
are
positioned
to
the*

axle spring seats
by
locating pins butt welded
to
the

spring
leaf.
CORVETTE

The Corvette independent three-link type rear
sus-

pension consists
of a
fixed differential carrier which
is

SPRING REAR SHACKLE

LEAF SPRING

SHOCK ABSORBER

SPRING FRONT MOUNT

Fig.
4—Comoro Rear Suspension Components

CHEVROLET CHASSIS SERVICE MANUAL

Page 194 of 659


REAR SUSPENSION AND DRIVE LINE
4-4

PROPELLER SHAFT

CARRIER FRONT SUPPORT
CAMBER CAM CONTROL ARM

Fig. 5—Corvette Rear Suspension and Driveline Components

rubber mounted to the frame at three points, with the .

strut rods, drive shafts and torque control arms forming

the three links at each wheel, and a transversely mounted

multi-leaf spring (fig. 5).

The bbx section trailing torque control arms are

mounted at the forward end into frame side member

openings through pivot bolts and rubber bushings, and

extend rearward to connect to the leaf spring. The

wheel spindles and spindle supports are attached to the

torque arms through four bolts pressed into the arm.

Rear wheel toe-in angle is adjusted through the use of

variable thickness shims inserted between the torque

arm and the frame side member web at the forward

pivoting joint.

The rear wheel spindles are driven through double

"U"
jointed, tubular driveshafts which are flange mount-

ed to a splined spindle flange at their outboard end and

bolted to the differential side gear yokes at their in-

board end. Wheel spindle support houses the inner and

outer tapered roller bearings, two to each wheel. Bear-

ing adjustment is made through the use of a spacer and

variable thickness shims between the bearings.

The spindle supports also incorporate integrally
forged, fork-shaped mounting brackets to accept the

outer ends of the rubber-bushed strut rods. The strut

rods are mounted laterally from the spindle support to

a bracket bolted to the lower surface of the axle car-

rier. The strut rod connection at this point is with an

eccentric cam arrangement and provides for rear wheel

camber adjustment.

The direct, double-acting shock absorbers are at-

tached at the upper eye to a frame bracket and at the

lower eye to the strut rod mounting shaft which incor-

porates a threaded stud for. the shock absorber lower

eye.

The transversely mounted multi-leaf spring is clamp

bolted at the center section to a lower mounting surface

on the differential carrier cover. The outer ends of the

main leaf are provided with a hole through which the

spring is link bolted to the rear of the torque control

arms.
The spring assembly is provided with full length

liners.

An optionally available stabilizer shaft attaches to the

upper rear section of the torque arms, and stretches

rearward where it is connected to the frame by two

rubber-bushed mounting brackets.

MAINTENANCE AND ADJUSTMENTS

Periodic maintenance and adjustments are not required

for the rear suspension components. The suspension

system should be checked for shock absorber action,
condition of suspension bushings, tightness of suspension

attaching bolts and an overall visual inspection of com-

ponents for defects.

CHEVROLET CHASSIS SERVICE MANUAL

Page 195 of 659


REAR SUSPENSION AND DRIVE LINE 4-5

Fig.
6—Measuring Rear Riding Height (Chevrolet and Chevelle)

RIDING HEIGHT CHECK

(Chevrolet, Chevelle Camaro and Chevy II)

In case of vehicle riding height complaints, a spring

height check will show if the rear suspension is at the

right height.

1.
Position car on smooth level floor.

2.
Vehicle must be at curb weight (full gas tank, no

passengers, spare and jack in trunk). Car should be

raised up a few times to allow suspension to settle

with car weight to eliminate friction at arm pivots.

3.
On Chevrolet and Chevelle models, measure riding
Fig.
8—Measuring Rear Riding Height (Camaro)

height as the distance from the top of the axle hous-

ing to frame kick-up (fig. 6).

4.
On Chevy II models, measure riding height as the

distance from lower surface of bumper support

bracket to top of axle housing (fig. 7).

5.
On Camaro models measure riding height as the

distance from jounce bumper upper attaching bolt to

top of axle housing (fig. 8).

6. Riding heights vary between models* Refer to speci-

fications section for vehicle and model application.

WHEEL ALIGNMENT (CORVETTE)

Camber

Wheel camber angle is obtained by adjusting the eccen-

tric cam and bolt assembly located at the inboard mount-

ing of the strut rod (fig. 9). Place rear wheels on

alignment machine and determine camber angle. To

adjust, loosen cam bolt nut and rotate cam and bolt as-

sembly until specified camber is reached. Tighten nut

securely and torque to specifications.

Fig.
7—Rear Riding Height (Chevy II)
Fig.
9—Ad
justing
Rear Wheel Camber (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

Page 196 of 659


REAR SUSPENSION AND DRIVE LINE 4-6

Fig.
10—Toe-in Adjusting Shim Location (Corvette)

Toe-in

Wheel toe-in is adjusted by inserting shims of varying

thickness inside the frame side member on both sides

of the torque arm pivot bushing (fig. 10). Shims are

available in thicknesses of
1/64",
1/32",
1/8" and 1/4".

To adjust toe-in, remove torque arm pivot bolt; then

position torque arm to obtain specified toe-in. Shim gap

toward vehicle centerline between torque arm bushing

and frame side inner wall.

NOTE: Do not use thicker shim than necessary,

and do not use undue force when shimming inner

side of torque arm - to do so may cause toe

setting to change.

Shim outboard gap as necessary to obtain solid stack-

up between torque arm bushing and inner wall of frame

side member. After correct shim stack has been se-

lected, install pivot bolt and hardened washers (fig. 10) -
making sure that all shims are retained - torque nut to

specifications and install cotter pin. If specified torque

does not permit cotter pin insertion, tighten nut to next

flat.

WHEEL BEARING ADJUSTMENT (CORVETTE)

inspection

The tapered-roller spindle bearings should have end

play of .001" to
.008".
During inspection, check end

play and, when necessary, adjust as outlined in this

section.

1.
Raise rear of vehicle until wheels clear ground.

2.
Disengage bolt lock tabs and disconnect outboard end

of axle drive shaft from wheel spindle flange.

3.
Mark camber cam in relation to bracket. Loosen and

turn camber bolt until strut rod forces control arm

outward. Position loose end of axle drive shaft to

one side for access to spindle.

4.
Remove wheel and tire assembly. Mount dial in-

dicator (Tool J-8001) on torque arm or adjacent

surface and rest pointer on flange or spindle end

(fig. H).

5.
Grasp brake disc and move axially (in and out) while

reading movement on dial indicator. If end movement

is within the .001" to .008" limit, bearings do not

require adjustment. If not within .001" to .008"

limit, record reading for future reference and adjust

bearings as outlined below.

Adjustment

1.
Apply parking brake to prevent spindle from turning

and remove cotter pin and nut from spindle.

2.
Release parking brake and remove drive spindle

flange from splined end of spindle.

3.
Remove brake caliper and brake disc as outlined in

Section 5.

4.
Install Thread Protector J-21859-2 over spindle

threads; then remove drive spindle from spindle

support, using Tool J-22602 as shown in Figure 12.

CAUTION: When using Tool J-22601 to remove

drive spindle, make sure puller plate is posi-

Fig.
11—Checking Wheel Bearing Adjustment (Corvette)
Fig. 12—Removing Drive Spindle from Support (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

Page 197 of 659


REAR SUSPENSION AND DRIVE LINE 4-7

tioned vertically in the torque arm before ap-

plying pressure to the puller screw.

5.
Remove shim and bearing spacer from spindle

support.

6. Note size of shim used. If dial indicator reading

was more than
.008",
select a shim thinner by the

amount needed to bring end play within limits. If

dial indicator reading was less than
.001",
select a

shim thicker by the amount needed to bring end play

within limits.

NOTE: Shims are available in thicknesses from

.097"
to .148" in increments of
.003".

EXAMPLE: Bearing end play reading obtained

on dial indicator was
.011",
.003" over limit.

Bearing shim removed from spindle measures

.145".
New shim installed measures .139", .006"

smaller. End play is now decreased by .006" and

is
.005",
which is within the .001" to .008" limit.

7.
After determining shim thickness, install bearing

spacer and shim on spindle. Position spindle in

spindle support.

8. Press inner bearing race and roller assembly on

spindle as follows.

a. Position Tool J-4731 over spindle and against

bearing inner race.

b.
Position washer and spindle nut on spindle and

proceed to tighten nut until bearing is forced on

spindle sufficiently to allow spindle drive flange

to be installed (fig. 13). Remove spindle nut,

washer and Tool
J-4731.
Discard nut and use a

new one for final assembly.

9. Position drive flange over spindle, making sure

flange is aligned with spindle splines. Install washer
Fig.
13—Installing Drive Spindle to Support (Corvette)

and nut on spindle then tighten nut to specifications

and install cotter pin. If specified torque does not

permit cotter pin insertion, tighten nut to next flat.

10.
Seat spindle support outer seal in bore by using

screw driver, or other suitable tool, to press against

metal portion of seal.

11.
Install brake disc and caliper. Refer to Section 5

for details of brake disc and caliper installation.

12.
Install axle drive shaft, wheel and tire assembly,

adjust camber cam to original position and torque

all components to specifications.

COMPONENT PARTS REPLACEMENT

(Chevrolet, Chevelle, Chevy II and Camaro)

COIL SPRING

Chevrolet

Removal

To remove either or both rear coil springs proceed

as follows.

1.
Raise rear of vehicle and place jack stands under

frame. Support vehicle weight at rear, using either

a jack or post of twin-post hoist under axle.

2.
Remove both rear wheels from vehicle.

3.
With the car supported as in Step 1, so that the rear

springs are compressed by weight of vehicle; per-

form the following:

a. Disconnect both rear shock absorbers from the

anchor pin lower attachment.

b.
Loosen the upper control arm(s) rear pivot bolt

(do not remove the nut).

C. Loosen both the left and the right lower control

arm rear attachment (do not disconnect from axle

brackets).

d. Remove the rear suspension tie rod from the

stud on the axle tube.

4.
At the lower seat of both rear coil springs, slightly

loosen the nut on the bolt that retains the spring and

seat to the control arm. When the nut has been

backed off the maximum permissible, all threads of
the nut should still be engaged on the bolt.

CAUTION: Under ,no condition should the nut,

at this time, be removed from the bolt in the

seat of either spring.

5.
Slowly lower the support (jack or hoist post) that has

been in place under the rear axle, thereby allowing

the axle to swing down, carrying the springs out of

their upper seat and providing access for spring

removal.

6. Remove the lower seat attaching parts from each

spring, then remove the springs from the vehicle

(fig. 14).

Installation

1.
Position the springs in their upper seat so that end

of top coil is 3/8" ± 1/8" from end of stop. Install

the lower seat parts on the control arm, with the nut

finger tight on the spring retainer bolt.

NOTE: Omit the lock washer under the special

high carbon bolt, so that sufficient bolt thread

will be available to start the nut. The lock

washers will be installed later (in Step 4).

2.
By alternately raising the axle slightly and then

re-snugging the nut on each spring lower seat bolt,

move the axle upward until vehicle weight is fully

CHEVROLET CHASSIS SERVICE MANUAL

Page 198 of 659


REAR SUSPENSION AND DRIVE LINE 4-8

Fig.
14—Coil Spring Installation (Chevrolet)

supported on the jack. With the spring now com-

pressed to approximately curb height, positively

position the springs in the lower seats by torquing

the nut on the lower seat bolt (fig. 15).

Re-connect shock absorbers, torque rear attach-

ment of upper and lower control arms, and re-

connect the axle tie rod at proper torque.

With the rear of vehicle still supported by jack under

axle;
remove the nut from the lower seat bolt of one

Fig.
15—Installing Coil Spring to Lower Control Arm (Chevrolet)
Fig.
16—Coil Spring Installation (Chevelle)

rear spring, slide proper lock washer on the bolt

and reinstall the nut to proper torque. Similarly

install a lock washer at the lower seat of the other

rear spring.

5.
Install rear wheels and lower vehicle to floor.

Chevelle

Removal

The following procedure may be utilized to replace

either or both rear coil springs.

1.
Raise vehicle to a height that will allow axle assem-

bly to hang freely, and position supports under both

frame side rails.

2.
Support axle assembly with an adjustable lifting

device, and disconnect shock absorber at axle

bracket. Shock absorber on side opposite need not

be disconnected if only one spring is being removed.

Refer to Shock Absorber Removal procedures out-

lined in this section.

3.
Lower axle assembly until suspension reaches end

of travel; then pry lower% pigtail over vertical re-

tainer on axle bracket and remove spring and insula-

tor from vehicle.

Installation

1.
Position rubber insulator on end of spring, making

sure that end of pigtail is butted against stop in

insulator. Install insulator and spring in upper

spring seat so that insulator is properly indexed

against stop (fig. 16).

2.
Pry lower pigtail portion of spring over vertical

flange of the axle bracket spring seat.

3.
Raise axle to allow shock absorber installation.

Position shock absorber in axle bracket. Torque nut

as outlined in Shock Absorber Installation

procedures.

4.
Lower vehicle and check rear riding height.

CHEVROLET CHASSIS SERVICE MANUAL

Page 199 of 659


REAR SUSPENSION AND DRIVE LINE 4-9

Fig.
17—Rear Spring—Exploded View (Chevy II)

LEAF SPRING, SPRING SEAT PADS, SPRING EYE

BUSHINGS Chevy II (Fig. 17)

Removal

1.
Raise vehicle and support rear axle assembly.

2.
Pull parking brake cable out of lower spring pad

mounting bracket clamp and disconnect cable above

axle housing. Remove four nuts securing lower

spring pad mounting bracket to axle spring seat

(fig. 18). Drop lower bracket and remove rubber

spring pad.

3.
Loosen and drive out front spring eye bolt. Lower

spring and remove front rubber eye bushing (fig. 19).

4.
Remove nuts from rear spring shackle (fig. 20),

spread shackle to separate it from spring eye and

support bracket and remove spring. Remove rear

spring eye bushings.

5.
Remove upper spring pad cushion.

Installation

1.
Inspect spring eye bushings and spring pads for ex-

cessive wear or aging and replace as necessary.

Inspect spring rear shackles, front spring bracket

and eye bolt for bending or cracking and correct

where needed.

2.
Assemble spring rear shackle as follows:

a. All except Station Wagons (fig. 21).
Fig.
19—Removing Front Eye Bushings (Chevy II)

3.
' Fig. 20—Disassembling Rear Spring Shackle (Chevy II)

1.
Insert inboard rubber spring eye bushings into

i'ear spring eye and outboard shackle bushings

into shackle mounting bracket.

2.
Position spring and install shackle to spring

and mounting bracket with top nut toward out-

board of vehicle and bottom nut toward vehicle

centerline.

3.
Tighten nuts but-do not torque at this point,

b.
Station Wagon (fig. 22):

When installing shackle as in Step 2 above, top

nut should be toward centerline of vehicle and

bottom nut toward outboard of vehicle.

Insert inboard rubber bushing into front spring eye.

Fig.
18—Removing Lower Pad Bracket (Chevy II)
Fig.
21—Rear Spring Shackle Exploded View-All

Except Station Wagon (Chevy II)

CHEVROLET CHASSIS SERVICE MANUAL

Page 200 of 659


REAR SUSPENSION AND DRIVE LINE 4-10

Fig.
22—Rear Spring Shackle Exploded View—Station Wagon

(Chevy II)

4.
Place upper spring pad cushion on spring. Raise

spring, making sure spring cushion ribs index with

locating ribs in axle housing spring seat, and insert

spring front eye and bushing in frame bracket. In-

stall spring eye bolt, bushing, retainer, lock washer

and nut. Do not torque at this point.

5.
Place lower spring pad cushion on spring, indexing

it over locating dowel.

NOTE: Upper pad correctly installed when

aligned with lower pad.

6. Place lower mounting plate into position over lo-

cating dowel on spring pad, install four locknuts and

insert shock absorber lower eye bolt.

7.
Remove adjustable jackstands, lower vehicle to floor

and bounce several times. Torque all affected parts

to specifications. Incorrect bushing preload may

result if spring eye bolts are torqued prior to

lowering vehicle.

Camaro (Fig. 23)

Removal

1.
Raise rear of vehicle sufficiently to allow axle as-

sembly to hang freely; then support weight of vehicle

at both frame side rails and near front eye of

spring.

Fig.
23—Rear Spring—Exploded View (Camaro)
Fig.
24—Removing Spring Front Bushing (Camaro)

2.
Raise axle assembly so that all tension is removed

from spring.

3.
Loosen and remove shock absorber lower attaching

bolt.

4.
Loosen the spring eye-to-bracket retaining bolt.

5.
Remove the screws securing the spring retainer

bracket to the underbody.

6. Lower axle assembly sufficiently to permit access to

spring retainer bracket and remove bracket from

spring.

7.
The spring eye bushing can be replaced without

completely removing the spring from the vehicle,

if bushing requires replacement proceed as follows.

a. Position remover adapter J-21978-1 over puller

screw J-21058-15 so that adapter is against head

of puller screw. Refer to Figure 24 for view of

removal tools.

b.
Position puller screw through eye of bushing so

that remover adapter J-21978-1 is against un-

flanged side of bushing.

C. Position large end of barrel J-22553-1 over

puller screw and seat barrel against spring eye.

d. Position thrust bearing on puller screw then in-

stall and tighten nut J-21058-8 against thrust

bearing.

e. Check to make sure that all puller parts are

properly aligned then proceed to tighten nut until

bushing is pulled free of spring eye--disassemble

puller tool.

f. Position installer adapter J-22553-2 over flange

end of bushing then position puller screw

J-21058-15 through installer adapter and bush-

ing. Refer to Figure 25 for view of installation

tools.

g. Position puller screw through spring eye until

bushing contacts spring. Install small end of

barrel J-22553-1 over puller screw and seat

barrel against spring.

h. Install thrust bearing and nut J-21058-8. Check

puller tools and bushing for proper alignment;

then tighten nut to pull bushing into spring.

NOTE: Do not apply additional torque to nut

J-21058-8 after bushing flange contacts spring.

CHEVROLET CHASSIS SERVICE MANUAL

Page:   < prev 1-10 ... 151-160 161-170 171-180 181-190 191-200 201-210 211-220 221-230 231-240 ... 660 next >