ECU CHEVROLET CAMARO 1967 1.G Chassis Repair Manual

ENGINE-ELECTRICAL 6Y-27

timing mark on pulley lines up with timing tab.

2.
Position distributor to opening in block in normal

installed attitude (fig. 15i), noting position of vacuum

control unit.

3.
Position rotor to point toward front of engine (with

distributor housing held in installed attitude), then

turn rotor counter-clockwise approximately 1/8 turn

more toward left cylinder bank and push distributor

down to engine camshaft. It may be necessary to ro-

tate rotor slightly until camshaft engagement is felt.

4.
While pressing firmly down on distributor housing,

kick starter over a few times to make sure oil pump

shaft is engaged. Install hold-down clamp and bolt

and snug up bolt.

5. Turn distributor body slightly until points just open

and tighten distributor clamp bolt.

6. Place distributor cap in position and check to see

that rotor lines up with terminal for No. 1 spark

plug.

7. Install cap, check all high tension wire connections

and connect spark plug wires if they have been re-

moved. It is important that the wires be installed in

their location in the supports.

NOTE:
The brackets are numbered to show the

correct installation. Wires must be installed as

indicated to prevent cross firing.

8. Connect vacuum line to distributor and distributor

primary wire to coil terminal.

9. Start engine and set timing as described under Turn-

Up in Section 6.

BREAKERLESS (MAGNETIC PULSE)

DISTRIBUTOR

REMOVAL (CORVETTE)

1.
If vehicle is equipped with radio, remove three bolts

securing ignition shield over distributor and coil.

One bolt is accessible from the top of shield, the

other two are at rear of shield, facing firewall.

2.
Disconnect tachometer drive cables from distributor

housing.

3.
Disconnect pickup coil leads at connector.

4.
Remove distributor cap.

5. Crank engine so rotor is in position to fire No. 1

cylinder and timing mark on harmonic balancer is

indexed with pointer.

6. Remove vacuum line from distributor.

7. Remove distributor clamping screw and hold-down

clamp.

8. Remove distributor and distributor-to-block gasket.

It will be noted that the rotor will rotate as the

distributor is pulled out of the block. Mark the re-

lationship of the rotor and the distributor housing

after removal so that the rotor can be set in the

same position when the distributor is being installed.

DISASSEMBLY (Fig. 16i)

NOTE:
If a distributor is being disassembled

for replacement of the stationary magnetic

pickup assembly only, it will be necessary to

perform only Steps 3, 4, 5, 7, 8, 9, and 12 of the

service procedure listed below.
1.
Remove screws securing rotor and remove rotor.

2.
Remove centrifugal weight springs and weights.

3.
Remove the tachometer drive gear from the distribu-

tor (Corvette only).

4.
Remove roll pin, then remove distributor drive gear

and washer.

CAUTION: To prevent

magnet, support drive gear
;e to the permanent

?n
driving out roll

pin.

5. Remove drive shaft assembly.

6. Remove centrifugal weight support and timer core

from drive shaft.

7. Remove connector from pickup coil leads.

8. Remove retaining ring which secures magnetic

core support plate to distributor shaft bushing in

housing.

9. As a unit, remove the entire magnetic pickup assem-

bly from the distributor housing.

10.
Remove brass washer and felt pad.

11.
Remove vacuum advance unit.

12.
To reassemble distributor, perform the above steps

in reverse order.

INSTALLATION (CORVETTE)

1.
Check to see that the engine is at firing position for

No.
1 cylinder (timing mark on harmonic balancer

indexed with pointer).

2.
Position a new distributor-to-block gasket on the

block.

3.
Before installing distributor, index rotor with hous-

ing as noted when distributor was removed. Install

distributor in block so that vacuum diaphragm faces

approximately 45° forward on the right side of the

engine and the rotor points toward contact in cap for

No.
1 cylinder.

4.
Replace distributor clamp leaving screw loose

enough to allow distributor to be turned for timing

adjustment.

5. Install spark plug wires in distributor cap. Place

wire for No. 1 cylinder in tower (marked on old cap

during disassembly) then install remaining wires

clockwise around the cap according to the firing

order (1-8-4-3-6-5-7-2).

6. Attach distributor to coil primary wires.

7. Replace distributor cap.

8. Adjust timing and then fully tighten distributor clamp

screw.

9. Attach vacuum line to distributor.

10.
Connect tachometer drive cables to distributor body.

11.
Replace ignition shields.

DISTRIBUTOR OFF-ENGINE TEST

The distributor's centrifugal and vacuum advance can

be checked in a distributor testing machine or synchro-

scope specially adapted or designed to accommodate this

type distributor. However, since this involves removing

the distributor from the engine, this test may be post-

poned until other system checks have been made. A dwell

reading cannot be obtained on this distributor and it is not

likely that the centrifugal or vacuum advance will be a

cause of trouble.

COIL REPLACEMENT

1.
Disconnect ignition switch and distributor leads from

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-28

terminals on eoil. On Corvettes equipped with radio,

remove bolts securing ignition shield over distribu-

tor and coil.

2.
Pull high tension wire from center terminal of coil.

3.
Remove the two coil support mounting bolts or loosen

friction clamp screw and remove coil.

4.
Place new coil in position and install attaching bolts

or tighten clamp screw.

5.
Place high tension lead securely in center terminal

of coil and connect ignition switch and distributor

primary leads to terminals on coil. Replace ignition

shield on Corvettes.

6. Start engine and test coil operation.

IGNITION PULSE AMPLIFIER

DISASSEMBLY

To check the amplifier for defective components, pro-

ceed as follows:

1.
Remove the bottom plate from the amplifier.

2.
To aid in reassembly, note the locations of the lead

connections to the panel board.

3.
Remove the three panel board attaching screws, and

lift the assembly from the housing.

4.
To aid in reassembly, note any identifying markings

on the two transistors and their respective locations

on the panel board and heat sink assembly.

5.
Note the insulators between the transistors.and the

heat sink, and the insulators separating the heat sink

from the panel board.

6. Remove the transistor attaching screws, and sepa-

rate the two transistors and heat sink from the panel

board.

7.
Carefully examine the panel board for evidence of

damage.

MOUNTING

SCREW

RESISTOR R5 jgSfe. / DIODE Dl

TRANSISTOR TR2

(UNDERNEATH)

1H L >©V

[So

To
I
/'%**jt\
\
TRANSISTC>R"""

1 X ^^w^ X \ (UNDERNEATH)

9^ESISTORR^^^H|^^^^^H

^B
RESISTOR
R4
^HPH^^H

WM'
RESISTOR
R3
I^B^^^^I^U

N .6 ®

mm

N%|/MOUNTING

• tr^i^w ^\ vjR SCREW

CAPACITOR
Cl\
pNkj^^A^
\
RESISTOR
Rl

MOUNTING ^55S^^ \ CAPACITOR C3

SCREW I RESISTOR R6 CAPACITOR C2

TRANSISTOR TR3
COMPONENT CHECKS (Figs. \7\ and 18i)

With the two transistors separated from the assembly,

an ohmmeter may be used to check the transistors and

components on the panel board for defects. An ohmmeter

having a 1-1/2 volt cell, which is the type usually found

in service stations, is recommended. The low range

scale on the ohmmeter should be used except where

specified otherwise.

A 25 watt soldering gun is recommended, and a 60% tin

40%
lead solder should be used when re-soldering. Avoid

excessive heat which may damage the panel board. Chip

away any epoxy involved, and apply new epoxy which is

commercially available.

In order to check the panel board assembly, it is

necessary to unsolder at the locations indicated in Fig-

ure 18i the two capacitors C2 and C3. In all of the fol-

lowing checks, connect the ohmmeter as shown and then

reverse the ohmmeter leads to obtain two readings. The

amplifier circuitry is shown in Figure 19i.

1.
Transistors TR1 and TR2: Check each transistor by

referring to Figure 20i. If both readings in Step 1

are zero, the transistor is shorted. If both readings

in Step 2 are zero, the transistor is shorted; and if

both readings are infinite, the transistor is open.

Interpret Step 3 the same as Step 2.

2.
Trigger Transistor TR3:
11
both readings in Step 1

are zero, the transistor is shorted. If both readings

in Step 2 are zero, the transistor is shorted; and if

both readings are infinite, the transistor is open.

Interpret Step 3 the same as Step 2.

3.
Diode Dl: 11 both readings are zero, the diode is

shorted; and if both readings are infinite, the diode

is open.

4.
Capacitor Cl: If both readings are zero, the capaci-

tor is shorted.

5.
Capacitors C2 and C3: Connect the ohmmeter across

CHECKING

RESISTOR Rl

UNSOLDER
I
CHECKING TRIGGER

TRANSISTOR TR3
CHECKING

CAPACITOR C

Fig.
171—Pulse Amplifier Panel Board
Fig.
18i—Pulse
Amplifier
Component
Checks

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-7

MAINTENANCE AND ADJUSTMENTS

CHEVROLET, CHEVELLE, CHEVY II, CAMARO,

SHIFT LINKAGE ADJUSTMENT

In cases where the gearshift linkage has been discon-

nected, it should be adjusted as follows:

1.
Move both transmission shift levers until transmis-

sion is in neutral. Neutral detents in transmission

cover must both be engaged to make this adjustment

correctly. (To check, start engine with clutch dis-

engaged, and release clutch slowly.)

2.
Move selector lever to neutral position. Align first

and reverse tube lever with the second and third

shifter tube lever on the mast jacket. This may be

done by having an assistant hold the mast .jacket shift

levers aligned in neutral position or use a simple

gauge or pin to align these levers in neutral.

3.
Make necessary adjustment to align shift control

rods and transmission levers in neutral position.

Move selector lever through all positions to check ad-

justment and to insure over-travel in all positions.

FLOOR SHIFT LINKAGE ADJUSTMENT

1.
Set Transmission Levers (K) and (L) in neutral de-

tent position.

2.
Move Transmission Control Lever (A) to neutral de-

tent and insert Locating Pin (D) into notch of Lever

and Bracket Assembly.

3.
Install Nut (N) and Clevis (M) on Rod (J) loosely,

attach Rod to Lever (B) and secure with retainer.

4.
With Lever (B) against Locating Pin, adjust Clevis

at Lever (L) until Clevis pin passes freely through

holes and secure with washer and cotter pin. Tighten

Nut (N).

5.
Install Nuts (E) and (G) and Swivel (F) loosely on Rod

(H),
attach Rod to Lever (K) and secure with retainer.

6. With Lever (C) against Locating Pin, attach Swivel to

lever and secure with retainer. iRun Nut (G) against

Swivel, then tighten Nut (E) against Swivel.

7.
Remove Locating Pin and check shifts to insure

proper operation. Readjust clevis and swivel if nec-

essary.

LEVER (A)
LEVER (L) CLEVIS (M)-NUT (N

LEVER (C)

ROD(J).
" - -

LEVER (K) ROD (H)^ NUT '(G) SWIVEL (F) ^NUT (E)
SHIFT CONTROL LEVER AND BRACKET ASSEMBLY

If disassembly of this control lever and bracket assem-

bly is necessary refer to Figure 2A for parts breakdown

and relative positioning for assembly.

SPEEDOMETER DRIVEN GEAR

Disconnect speedometer cable, remove lock plate to ex-

tension bolt and lock washer and remove lock plate. In-

sert screwdriver in lock plate slot in fitting and pry fitting

gear and shaft from extension. Pry "O" ring from groove

in fitting.

Install new "OM ring in groove in fitting. Coat "O" ring

and driven gear shaft with transmission lubricant and in-

sert shaft.

Hold the assembly so slot in fitting is toward lock plate

boss on extension and install in extension. Push fitting

into extension until lock plate can be inserted in groove

and attach to extension.

EXTENSION OIL SEAL REPLACEMENT

.1.
Remove propeller shaft as outlined in Section 4 and

disconnect any necessary items to obtain clearance.

2.
Pry seal out of extension.

3.
Wash counterbore with cleaning solvent and inspect

for damage.

4.
Prelubricate between sealing lips and coat new seal

O.D. with Permatex or equivalent and start straight

in bore in case extension. Using Tool J-5154, tap

seal into counterbore until flange bottoms against

extension.

Fig.
1A- Shift Linkage Adjustment (Typical)
Fig.
2A - Corvette 3 Speed Control Lever and Bracket Assembly

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-14

SPEED HEAVY DUTY TRANSMISSION

(WARNER MODEL T 16)

INDEX

General Description ......

Maintenance and Adjustments

Shift Linkage Adjustment

Side Cover ........

Removal .........

Disassembly
7-14

7-14

7-14

7-14

7-14

7-14
Assembly 7-14

Installation • 7-15

Other Maintenance
&
Adjustment

Operations See 3-Speed Saginaw Section

Transmission Replacement . . . See 3-Speed Saginaw Section

GENERAL DESCRIPTION

The Borg-Warner heavy duty three speed fully syn-

chronized (all forward gears) transmission incorporates

helical gears throughout specially designed to provide

high torque capacity, and gear teeth proportion to operate

at high speeds with neither excessive heat generation nor

excessive frictional losses. Shafts, bearings, high ca-

pacity clutches and other precision parts are held to

close limits providing proper clearances necessary for

durability during extended heavy usage.

The main drive gear is supported by a heavy duty ball

bearing at the front end of the transmission case and is

piloted at its front end in an oil impregnated bushing

mounted in the engine crankshaft. The front end of the

mainshaft is piloted in a row of roller bearings set into

the hollow end of the main drive gear and the rear end

is carried by a heavy duty ball bearing mounted in the

front of the extension housing.

The countergear is carried on a double row of rollers

at both ends while thrust is taken on thrust washers lo-

cated between the ends of the gear and the thrust bosses

in the case. An anti-rattle plate assembly at the front
of the countergear provides a constant spring tension be-

tween the counter and clutch gears to reduce torsional

vibrations. The reverse idler gear is carried on 25

roller bearings while thrust is taken on thrust washers

located between the ends of the gear and the thrust bosses

of the case.

Gear shifting is manual through shift control rods from

the shifter tube in the mast jacket to the rearward shift

lever of the side cover assembly for first and reverse

gear; and through a cross shaft assembly attached to the

forward side cover lever for second and third gear. All

three forward gears are fully synchronized. The syn-

chronizer assemblies consist of a clutch hub, clutch

sleeve, two clutch key springs and three energizer clutch

keys and are retained as an assembly on the main shaft

by a snap ring. The transmission may be used as an aid

in deceleration by downshifting in sequence without

double-clutching or any gear clashing. Reverse is not

synchronized, however, it is a helical gear to insure

quiet operation.

MAINTENANCE AND ADJUSTMENTS

Refer to similar procedures under the 3-speed Saginaw

Transmission Section for—Column Mounted Shift Linkage

Adjustment, Speedometer Driven Gear and Oil Seal Re-

placement, Extension Oil Seal Replacement and Trans-

mission Replacement. ~~

Camaro and Corvette Floor Shift Linkage Adjustment

(Fig.
lc)

1.
Set Lever (L), (K) in neutral position.

2.
Move Lever Assembly (A) and Levers (C), (D) to

neutral position and insert Locating Gauge (B) into

control Lever Bracket Assembly.

3.,
Install Rod (H) with Retainer (M) on Lever (L).

4.
With two Jam Nuts (G), (E) and Swivel (F) loose on

Rod (H) insert and attach Swivel with Retainer (N)

to Lever (D).

5.
Repeat steps 3 and 4 for Rod (J) and Levers (C
&
K).

6. Remove' Locating Gauge and check shift to insure

proper operation.

SIDE COVER ASSEMBLY

Removal

1.
Drain transmission and disconnect control rod and

cross shaft from side cover levers. *

2.
Remove nine cap screws securing the transmission

side cover assembly to transmission, case and re-

move cover assembly, shifting forks, and gasket.
Disassembly (Fig. 2C) '

1.
Remove shifting forks from shift lever assemblies.

2.
Remove nut and lock washer from each shift lever

shaft.

3.
Remove outer shift levers and lightly tap shift lever

shafts from assembly.

4.
Remove two steel balls, poppet spring, interlock pin

and interlock sleeve from cover.

5.
Remove "O" ring seals from shift lever shafts.

Assembly (Fig. 2C)

1.
Install new "O" ring seals to shift lever shafts.

2.
Install low and reverse shifter shaft and plate as-

sembly to cover.

3.
Place shifter shaft and plate assembly in neutral po-

sition, middle detent, and install interlock sleeve,

ball, poppet spring and interlock pin.

4.
Install remaining poppet ball and then install second

and third shifter shaft and plate assembly.

NOTE: Installation is easiest if shifter shaft

and plate assembly passes over ball in its neu-

tral position.

5.
Check clearance between end of interlock sleeve and

shifter shaft and plate cams when one plate is in

neutral and the other is shifted into gear position.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-15

LOCATING

GAGE B

N

Fig.
1C - Warner T-16 3-Speed Lever and Linkage Adjustment (Camaro and Corvette)

Clearance should be .002 to .008. Interlock sleeves

are available in four sizes to give the proper

clearance.

6. Install outer shifter levers to shafts with lock wash-

ers and nuts. Tighten securely. v

7.
Instill shifting forks to shift levers (1st and re-

verse fork "hump" towards bottom).

Installation

1.
Install new side cover gasket to transmission case,

install cover and secure with lock washers and cap

screws.

NOTE: The two rear side cover to case at-

taching bolts have a special oil sealing spline

and must be used at these two "through" hole

locations.

2.
Connect control rod and cross shaft to control

levers.

1.
Side Cover

2.
Poppet

3. 1st and Reverse Shifter

Lever and Shaft

4.
Poppet Spring

5. 1st and Reverse Shifter

Fork
6. Interlock Pin

7. 2nd and 3rd Shifting

Fork

8. Interlock Sleeve

9. 2nd and 3rd Shifter

Lever and Shaft

10.
"O11 Ring Seal

Fig.
2C - Side Cover Assembly - Layout

CHEVROLET CHASSIS SERVICE MANUAl

CLUTCH AND TRANSMISSIONS 7-29

ROD
(E)~X\

or

POINT OF-i-7V

CONTACT
i

(2)
-

VIEW

^ROD
(C

LLEVER
r-D

I

j

.——j

A

{

(D)
ETENT

FWD.

B
\_
(?) LOAD (X)

SWIVEL (J)-\

ROD(CK V

NUT (B)-—-^

SPACER
(H)-^
K

/ / n

/LOAD (Y)

I^-NUT
(A)

k-.O94

/^A
VIEWB

L-DETENT
(F)

AQUATING LEVER

-PART
OF
LEVER
&
(G)

BRKT. ASM.

Fig.
10PG - Corvette Gear Shift Control Adjustment

Fig.
9PG - Comoro Floor Shift Linkage Adjustment

The foregoing procedure will provide a .050" over

travel gap in the notches of Detent (F).

Corvette Linkage Adjustment (Fig. 10PG)

1.
Set Transmission Bell Crank (E) in "PARK" position.

2.
Set Control Shaft Lever (A) in "PARK" position.

3.
Install Clevis (D) on Rod (B) loosely, attach Rod to

Bell Crank (E) and secure with retainer.

4.
With Lever (A) in "PARK'? position, adjust Clevis

at Lever (A) until clevis pin passes freely through

holes and secure with washer and cotter pin.

5. Check shifts to insure proper operation. Readjust

Clevis as necessary.

Corvette Powerglide Control Lever

and Bracket Assembly

Powerglide control lever and bracket assembly is a

straight line shift type, mounted to the floor of the body

rather than the transmission extension as in the past.

Shifting from one detent position to another is done by

depressing a round button located in the center of the

spherical' shift lever knob. If disassembly of this control

lever and bracket assembly is necessary, refer to Figure

11PG for parts breakdown and relative positioning for

assembly.

Floor Mounted Control Lever

and Bracket Assembly (Exc. Corvette)

If disassembly of this control lever and bracket as-

sembly is necessary, refer to Figure 12PG for parts

break down and relative positioning for assembly.
Throttle Valve Linkage Adjustment

L-4 and L-6 Models

With accelerator pedal depressed, Bell Crank on L-4

and L-6 models must be at wide open throttle position.

Dash Lever must be 1/64"-1/16" off Lever Stop and

Transmission Lever must be against transmission in-

ternal stop.

Fig.
11PG - Corvette Control Lever and

Bracket Assembly - Exploded

CHEVtOLET CHASSIS SERVICE

SECTION 8

FUEL TANK AND EXHAUST SYSTEMS

CONTENTS OF THIS SECTION

Page

Chevrolet .. . . 8-1

Fuel Tanks 8-1

Exhaust Systems 8-5

Chevelle 8-8

Fuel Tanks 8-8

Exhaust Systems 8-11

Chevy n ...... 8-13

Fuel Tanks 8-13
Page

Exhaust Systems 8-16

Corvette 8-18

Fuel Tanks 8-18

Exhaust Systems 8-24

Camaro 8-26

Fuel Tank 8-26

Exhaust System 8-30

Special Tools 8-33

CHEVROLET

FUEL TANKS

INDEX

Page

Page

General Description

Component Part Replacement

Fuel Tank
8-1 Fuel Lines 8-3

8-2 Fuel Tank Vent Lines 8-4

8-2 Metering Units (Gauge Sending Unit ) 8-4

GENERAL DESCRIPTION

All Sedan models (fig. 1) use a 24 gallon capacity

(approx.) fuel tank mounted between the frame rails

behind the rear axle. The fuel tanks are held in place

by two straps attached individually to the underbody at

each end. The strap? hinge at the forward end and secure

the tank at the rear with a nut and bolt. Anti-squeak

material is cemented to the tank at the strap locations.
A vent line from the forward-right side of tank extends

over a clip on the upper portion of wheelhouse.

The station wagon fuel tank has a 24 gallon capacity

(approx.). The tank is located at the back of the left rear

quarter wheelhouse area. The front of the tank is en-

closed with a protective shield (fig. 1).

VIEW A ^QUARTER PANEL

SEDAN

STATION WAGON
I

Fig.
1-Fuel
Tanks

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-4

Fig.
5— Meter Assembly Removal Using Tool J-22554

vehicle. The fuel lines should be occasionally inspected

for leaks, kinks or dents. If evidence of dirt is found in

the carburetor or fuel pumto and disassembly, the lines

should be disconnected
and
blown out. Check the fuel tank

strainer for damage or omission. Note position of fuel

line clips for convertible models.
FUEL TANK VENT LINE

Sedan modei fuel tanks are vented to the atmosphere

at the top right- forward edge of. the tank. The vent line

is connected by a rubber hose with two clamps one at the

tank and the other at the vent pipe which is secured to

the underbody A rubber grommet around the vent pipe

acts as a seal to prevent gasoline fumes from entering

the.passenger compartment.

IMPORTANT: It is important to note that the

sedan gas tank cap is non-vented. It is neces-

sary to be assured that the vent line is free from

dirt, etc., and open at all times. If gasoline

fumes are detected, the rubber grommet should

be checked.

Station wagon models use a vented, anti-surge type gas

tank.

GAUGE UNIT AND FUEL STRAINER

Removal and Installation (Fig. 4)

1.
Follow tank removal procedure.

2.
Use Special Tool J-22554 (fig. 5) to remove cam

lock on sedan models and Tool J-8950 on station

wagons.

3.
Remove unit and rubber gasket.

4.
Reverse procedure to install.

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK
AND
EXHAUST SYSTEMS
8-5

EXHAUST SYSTEMS

INDEX

Page

General Description
. . 8-5

Component Part Replacement
8-5

Muffler Assembly.
8-5

Exhaust Pipes.
8-5

Tail Pipes.
8-5

GENERAL DESCRIPTION

All exhaust systems used
on the 1967
Chevrolet
are
exhaust systems
(fig. 7) are
available
as
regular produc-

the split system type
in
which the. component parts
are
tion equipment
on the 427 cu. in.
displacement
V-8 en-

secured together with clamps.
The
single exhaust system gines
and as an
option
on the
other (except
283 cu. in.)

used
on L-6
engine models
(fig. 6)
consists
of an
exhaust
V-8
engines. These systems consist
of two
exhaust

pipe, muffler, tailpipe
and
attaching hardware.
On V-8
pipes, mufflers, tailpipes with resonators
and
attaching

engine single exhaust models
a
crossover pipe
is
added hardware.
All
exhaust systems
are
suspended on brackets

to connect
the
right exhaust manifold
to the
system. Dual with insulators
for
rattle free operation.

COMPONENT PART REPLACEMENT

Care should
be
taken
to
have
the
exhaust pipe, muffler

or tail pipe
in
proper relation with each other. Incorrect

alignment frequently causes annoying rattles
due to in-

correct clearances.

MUFFLER ASSEMBLY

Remove
and
Replace

1.
Remove "U" bolt clamp
at
center mounting.

2.
Remove
"U"
bolt clamp
at
forward
end of
muffler

pipe.

3.
Disengage muffler
at
exhaust
and
tail pipe

connections.

4.
Three-fourths inch clearance should
be
allowed
be-

tween
the
muffler bracket (hanger)
and
crossmember

at installation.

5. Install unit with
the
flat side
of the
muffler showing.

EXHAUST PIPE (CROSSOVER WITH
V-8
ENGINE)

Remove
and
Replace

1.
Remove
two
nuts, extension
and
packings-separate

pipe from manifold.
2.

3.
Disassemble

pipe.
"U"
damp from muffler
and
remove

Attach pipe
to
muffler, then secure
to
manifold. Note

clearances
for the
standard
and
automatic control

linkages, underbody
and
crossmember. Contact
of

exhaust pipe
to
engine panrail
is
permissible.

4.
Tighten nuts uniformly.

TAIL PIPE AND/OR RESONATOR

Remove
and
Replace

1.
Remove
"U"
clamp attachment
at
muffler.

2.
Remove screw attachment
at
tail pipe rear hanger

assembly.

3.
Remove tail pipe.

4.
Replace tail pipe
at
muffler, then install
at
hanger

Do
not
secure attachments until clearances have been

checked. Check position
of
hanger
so
that interplates

are parallel.

5. Torque nuts
7-9 ft. lbs. at
hanger
and 10-15 ft. lbs.

at muffler.

CHEVROLET CHASSIS
SEI

FUEL TANK AND EXHAUST SYSTEMS
8-8

CHEVELLE

FUEL TANKS

INDEX

Page

General Description.
g.g

Component Part Replacement
8-8

Fuel Tanks
. 8-8

Fuel Lines
8-8
Metering Units (Gauge, Sending Unit)

Fuel Tank Filler Neck Caps.
. .

Fuel Tank Vent Lines
Page

8-8

8-8

8-9

GENERAL DESCRIPTION

All models
use a 20
gallon capacity (approx.) fuel tank

mounted between
the
frame rails behind
the
rear axle.

The fuel tanks
are
basically
the
same
for
sedan, 2-seat

station wagon
and
pickup models except
for
filler neck

location
and
venting
(fig. 8).

All fuel tanks
are
vented
to the
atmosphere. Sedan

model tanks have
an
external vent hose and pipe assem-

bly
(fig. 11) and use a
non-vented fuel cap. Station wagon

and pickup model tanks
are
vented through
a
hose
and

vent pipe assembly
to the
filler neck
(fig. 8)
and
use a

vented, anti-surge type
gas cap. The
fuel caps
are two

different designs conforming
to SAE
standards
and are

not interchangeable.

The filler neck assembly
on
sedan models
is a
rear

fill design located behind
the
center
bar of the
bumper.
Station wagon
and
sedan pickup model filler neck assem-

blies
are
located
in
the left rear quarter panel.

The fuel pickup pipe
is
built integrally with
the
tank

gauge, located
at the
top-front center
of
the tank.
A
fine

mesh screen
is
located
at
the bottom-end
of the
fuel pick-

up pipe
to
prevent
the
entrance
of
foreign material into

the fuel system.

The sedan fuel tanks
are
held
in
place
by
two metal

straps attached individually
to the
underbody
at
each
end.

The straps hinge
at the
forward end and secure
the
tank

at
the
rear with
an
adjustable bolt
and nut
assembly.

The station wagon
and
pickup models have
a
frame

mounted fuel tank secured with straps
to
front and rear

supports.

COMPONENT PART REPLACEMENT

FUEL TANK

Draining Tank

The absence
of a
drain plug
in the gas
tanks makes
it

necessary
to
siphon fuel from
the
tank when draining
is

needed. Refer
to the
recommended draining procedures

previously outlined under Chevrolet Models
in
this

section.

Removal
and
Installation (Sedan Models)

1.
Raise vehicle.

2.
Drain fuel tank.

3.
Disconnect fuel pickup line
and
gauge wires from

tank unit.

4.
Disconnect vent hose from tank.

5. Remove tank support straps and lower tank carefully.

6.
To
install, reverse
the
removal procedure.

Removal
and
Installation

(Station Wagon
and
Pickup)

1.
Follow Steps
1
thru
3
outlined under sedan models.

2.
Remove tank support straps.

3.
Remove frame screw attachments from
the
front

support
(fig. 8).

4.
Guide tank forward
and
remove.

5.
To
install, reverse removal procedure.

FUEL LINES

The fuel lines, extending from fuel tank toiiuelpump,

are routed
on the
underside
of the
underbody along
the

right side
of the
vehicle opposite
the
single exhaust
sys-

tem.
The
fuel lines should occasionally
be
inspected
for
leaks,
kinks,
or
dents.
If
evidence
of
dirt
is
found
in the

carburetor
or
fuel pump
on
disassembly,
the
lines should

be disconnected
and
blown
out.
Check
the
fuel tank

strainer
for
damage
or
omission. Fuel lines
are of 5/16"

diameter tubing with beaded type ends
for
connections
of

hoses.

FUEL PIPE RETAINER
CUP

Removal
and
Installation

If fuel pipes
and
retainer clips
are
removed, Tool

J-7777 should
be
used
to
install
new
retainer clips
(fig.

10).
After removal
of the old
clip from
the
frame, position

the
new
clip
in the
location
of the old
clip. Index
the

"blind rivet"
and
press hard (hand pressure should
do)

to expand rivet.

GAUGE UNIT
AND
FUEL STRAINER

Removal
and
Installation
(Fig. 11)

1.
Drain tank
to a
level below
the
unit.

2.
Disconnect fuel pickup line
and
gauge unit wire.

3.
Use
special Tool J-8950
to
remove
cam
lock.
Re-

move unit
and
rubber gasket.

CAUTION: Carefully remove unit
so as not to

damage screen
on the end of
the pipe.

4.
Clean screen
by
blowing
out
with compressed
air.

5. Reverse procedure
to
install.

FUEL TANK FILLER NECK CAPS

The fuel tank filler neck caps
are
non-vented with
an

anti-surge feature. Station wagons have vented caps.

(Refer
to
"Fuel Tank Vent Lines").

CHEVROLET CHASSIS SERVICE MANUAL