display Citroen BERLINGO MULTISPACE 2015 2.G Owner's Manual

16
Berlingo-2-VP_en_Chap02_eco-conduite_ed01-2015
Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO2
emissions.
Eco-driving
Optimise the use of your gearbox
With a manual gearbox, move off gently and change up without   waiting.   During   acceleration   change   up   early.
With
  an   automatic   or   electronic   gearbox,   give   preference  
to

  automatic   mode   and   avoid   pressing   the   accelerator  
pedal

  heavily   or   suddenly.
The
  gear   shift   indicator   invites   you   engage   the   most  
suitable

  gear:   as   soon   as   the   indication   is   displayed   in   the  
instrument

  panel,   follow   it   straight   away.
For
  vehicles   fitted   with   an   electronic   or   automatic   gearbox,  
this

  indicator   appears   only   in   manual   mode.
Drive smoothly
Maintain a safe distance between vehicles, use engine
braking  rather   than   the   brake   pedal,   and   press   the  
accelerator

  progressively.  
These
  practices   contribute  
towards

  a   reduction   in   fuel   consumption   and   CO
2
emissions
 
and
 
also
 
helps
 
reduce
 
the
 
background   traffic  
noise.
If

 
your
 
vehicle
 
has
 
cruise
 
control,
 
make
 
use
 
of
 
the   system  
at

 
speeds
 
above
 
25
 
mph
 
(40
 
km/h)
 
when
 
the
 
traffic   is  
flowing

 
well.
Control the use of your electrical
equipment
Before moving off, if the passenger compartment is too warm,   ventilate   it   by   opening   the   windows   and   air   vents  
before

  using   the   air   conditioning.
Above
  30   mph   (50   km/h),   close   the   windows   and   leave   the  
air

  vents   open.
Remember
  to   make   use   of   equipment   that   can   help   keep  
the

  temperature   in   the   passenger   compartment   down  
(sunroof

  and   window   blinds...).
Switch
  off   the   air   conditioning,   unless   it   has   automatic  
regulation,

  as   soon   as   the   desired   temperature   is   attained.
Switch
  off   the   demisting   and   defrosting   controls,   if   not  
automatic.
Switch

  off   the   heated   seat   as   soon   as   possible.
Switch
  off   the   headlamps   and   front   foglamps   when   the  
level

  of   light   does   not   require   their   use.
Avoid
  running   the   engine   before   moving   off,   particularly   in  
winter;

  your   vehicle   will   warm   up   much   faster   while   driving.
As
  a   passenger,   if   you   avoid   connecting   your   multimedia  
devices

  (film,   music,   video   game...),   you   will   contribute  
towards

  limiting   the   consumption   of   electrical   energy,   and  
so

  of   fuel.
d

isconnect your portable devices before leaving the
vehicle.
Motoring & Environment

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
28
Dials
1. Distance  recorder   in   kilometres   /  miles.
2.
 
Display
  screen.
3.
 
Fuel
  gauge,   coolant   temperature.
4.
 
Rev
  counter.
5.
 
T
rip   distance   recorder   /   service  
indicator

  reset.
6.
 
Instrument
  panel   lighting   dimmer.Level 1
INSTRUMENT PANELDisplay screens
Screens
The format of the information presented in the screen depends on
the
  vehicle's   equipment   level.
Level 2
with the touch screen tablet
Instruments and controls

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
29
Centre console with screen
Instrument panel without screen
-
 
T
urn   to   the   left:   24H   or   12H   is  
displayed.
-


T
urn to the right to select 24H
or
  12H.
-
 
T
urn   to   the   left   to   complete   the   time  
adjustment.
After

  approximately   30   seconds  
without any action, the screen returns
to

 
the   normal   display.
DATE AND TIME
Centre console without screen
The display - time sequence is  linked   according   to   model  
(version).

 
The
  access   to  
the

  "Date"   adjustment   is  
only

  active   when   the   model  
version

 
of
fers  
a
 
date
 
in
 
words.
T

o
 
adjust
 
the
 
time,
 
use
 
the
 left-hand button on the
instrument
 
panel:
-
 
T

urn
 
to
 
the
 
left:
 
the
 
minutes
 
flash.
-

T

urn to the right to increase the
minutes
 
(hold
 
the
 
button
 
to
 
the
 
right
 
for

 
rapid
 
scrolling).
-
 
T

urn
 
to
 
the
 
left:
 
the
 
hours
 
flash.
-

T

urn to the right to increase the
hours (hold the button to the right
for
 
rapid
 
scrolling).
Instruments and controls
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
33Warning lamp isindicatesSolution - action
Coolant
temperature
and level on with needle
in the red
zone.
an
  abnormal   increase   in  
temperature.Park

  and   switch   off   the   ignition   then   allow   to   cool.  
V

isually   check   the   level.
flashing. a
  drop   in   the   coolant   level.Chapter
  7,   "Levels"   section.
Contact
  a   CITROËN dealer   or   a   qualified  
workshop.
Service on

  temporarily. minor   faults   or   warnings.Consult
  the   alert   log   in   the   display   or   screen.
If
  your   vehicle   is   equipped   with   a   trip   computer   or  
a

  screen:   refer   to   the   "Steering   mounted   controls"  
section

  in   Chapter   4.
Contact
  a   CITROËN   dealer   or   a   qualified  
workshop.
remaining

  on. major   faults.
Seat belt not
fastened on then
flashing.
the
  driver   and/or   front  
passenger has not fastened
their

  seat   belt.Pull
  the   strap   then   insert   the   tongue   in   the   buckle.
accompanied
 
by an audible
signal then
remains

  on.the
  vehicle   is   moving   with  
the

  driver's   and/or   front  
passenger's seat belt not
fastened.Check

  that   the   seat   belt   is   fastened   by   pulling   the  
strap.
Chapter

  5,   "Seat   belts"   section.
ECO on.
The
  Stop   &   Start system  
has put the engine in
ST

OP
 
mode   following   a  
vehicle

  stop   (red   light,   traffic  
jam, etc...).As

  soon   as   you   want   to   move   off,   the   warning  
lamp

  goes   off   and   the   engine   restarts  
automatically

  in   START
 
mode.
flashes
  for   a  
few seconds,
then

  goes   off.STOP
 

mode   is   temporarily  
unavailable.
or
ST

ART
 
mode   has   been  
invoked

  automatically.Chapter
  3,   "Stop   &   Start"   section.
Instruments and controls
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
+
ABS
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
35Warning lamp isindicatesSolution - action
Power
steering on. a fault with the
system.The vehicle retains conventional steering without
assistance.
  Have   it   checked   by   a   CITROËN  
dealer

  or   a   qualified   workshop.
Door open
detection on
  and   accompanied  
by

  a   message   in   the  
screen.that a door is not
closed

  correctly.Check
  that   all   of   the   doors   are   closed.
ABS remaining
  on.a fault with the anti-
lock
  braking   system.The
  vehicle   retains   conventional   braking.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.
ESC flashing.
triggering of the
a

SR
or
  DSC   regulation.The
  system   optimises   traction   and   improves   the  
directional

  stability   of   the   vehicle.
Chapter
  5,   "Driving   safety"   section.
remaining
  on.a fault with the
system.
E.g.:
  under-inflation  
of

  the   tyres.E.g.:
  check   the   pressure   of   the   tyres.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.   (Wheel   speed   sensor,  
hydraulic

  valve   block,   ...).
Under-
inflation on.
The tyre pressure is
too
  low   in   or   more  
wheels.Check

  the   tyre   pressure   as   soon   as   possible.
This
  check   must   be   done   with   the   tyres   cold.
flashing
  then
 remaining

  on,
 accompanied

  by   the
 Service

warning
lamp,
  and   depending
 on

  equipment,   the
 display

  of   a   message.The tyre pressure
monitoring
  system  
has a fault or one of
the wheels does not
have

  a   sensor.Detection
  of   under-inflation   is   no   longer   assured.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.
Particle filter on. a
  problem   with   the  
particle

  filter   (fuel  
additive

  level,   risk   of  
blockage, ...).Have

  the   filter   checked   by   a   CITROËN   dealer   or  
a

  qualified   workshop.
Chapter
  7,   "Levels"   section.
Instruments and controls
REadY To Go
3

+
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
38
AdBlue® additive
For more information, refer to Chapter 7, "AdBlue additive" section.
Alert
Information Solution - action
1st level of alert
There   is   an   audible   signal   when   the   ignition   is   switched   on.
The
  warnings   are   intermittent   and   then   become   permanent
 when

  switching   on   the   ignition   or   when   driving.
The
  remaining   driving   range   is   counted   down   from   1   500   miles
 (2

  400   km)   to   375   miles   (600   km).
The
  range   figure   reduces   in   steps   of   200   miles   (300   km).
The contents of the additive tank has dropped to a level  sufficient   for   a   range   of   less   than   1   500   miles  
(2

  400   km).
Have
  the   tank   topped-up   using   an  
AdBlue®
container
 
or
 
bottles.
2
nd level of alert
There is an audible signal when the ignition is
switched
  on.
The
  warnings   are   intermittent   (every   30   seconds)  
and

 
then
 
become
 
permanent
 
every
 
time
 
the
 
ignition
 
is

 
switched   on   or   when   driving.
The
  remaining   driving   range   is   counted   down   from  
350

  miles   (600   km)   to   zero,   reducing   in   steps   of  
30
  miles   (50   km). You
must have the
a

dBlue
® additive topped-up and
not
 
wait
 
for
 
a
 
breakdown.
In the display
screen. Temporary
 
display:
 
"NO
 
START
 

IN".
In the touch
screen
 
tablet. Select:
-
 
"Driving

 
assistance".
-
 
"Diagnostic". The

 
driving
 
range
 
is
 
displayed.
3
rd level of alert
The a dBlue® additive tank is empty. Starting is impossible.
It is essential to add at least 3.8 litres of a dBlue®
additive
 
to
 
the
 
additive
 
tank.
Instruments and controls

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015

+ +
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
39
SCR emissions control system
Alerts InformationSolution - action
The   UREA,   Service   and   diagnostic   warning   lamps  
come

  on,   an   SCR   emissions   control   system   fault  
has

  been   detected. This
  is   is   temporary   fault,   the   alert   disappears   as  
soon

  as   the   exhaust   emissions   return   to   normal  
levels.
After 30 miles (50 km) without additive
Confirmation

  of   the   fault   which   is   not   related   to   a  
lack

  of   additive. The
  remaining   driving   range   700   miles   (1   100   km).
Go
  to   a   CITROËN   dealer   or   a   qualified   workshop  
as

  soon   as   possible   to   avoid   a   breakdown.
The
  fault   is   confirmed.
The
  next   time   the   ignition   is   switched   on,   the  
authorised

  driving   range   will   be   displayed   in   miles  
(kilometres)

  and   the   alert   will   be   repeated   every  
30
  seconds.
The
  limit   of   the   driving   range   has   been   reached,  
exhaust

  emissions   levels   are   above   the   limits.
Starting
  is   impossible. To restart the engine, you must contact a
CITROËN
  dealer   or   a   qualified   workshop.
- BlueHDi Diesel
Instruments and controls
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
42
The alert is maintained until the tyre or tyres concerned is
reinflated,  repaired   or   replaced.
The spare wheel (space-saver type or
a
 
steel   rim)   does   not   have   a   sensor.
Operating fault
Under-inflation alert
The loss of pressure detected
does not always lead to visible
deformation
 
of
 
the
 
tyre.
 
Do
 
not
 
rely
 
on

  just   a   visual   check.
The
 
alert
 
is
 
given
 
by
 
the
 
fixed illumination
 
of
 
this
 
warning
 
lamp, accompanied

 
by

 
an

 
audible

 
signal, and

 
depending
 
on
 
equipment,
 
the
 display

 
of
 
a
 
message. The
  flashing   and   then  fixed
  illumination   of   the  under-inflation
  warning  
lamp

  accompanied   by   the  
illu

mination   of   the   "Service"   warning  
lamp,

  and   depending   on   equipment,  
the

  display   of   a   message   indicates   a  
fault

  with   the   system.
In
  this   case,   monitoring   of   the   tyre  
pressures

  is   not   assured.
In
 
the
 
event
 
of
 
a
 
problem
 
on
 
one
 
of
 
the

 
tyres,
 
the
 
symbol
 
or
 
the
 
message
 
appears,

 
according
 
to
 
equipment,
 
to
 
identify

 
it.
-

Reduce speed, avoid sudden
steering

 
movements
 
or
 
harsh
 
brake
 
applications.
-

 
Stop

 
as
 
soon
 
as
 
it
 
is
 
safe
 
to
 
do
 
so.
-

In the event of a puncture, use
the

 
temporary
 
puncture
 
repair
 
kit
 
or the spare wheel (according to
equipment),
or
-

 
if

 
you
 
have
 
a
 
compressor,
 
the
 
one
 
in

 
the
 
temporary
 
puncture
 
repair
 
kit

 
for
 
example,
 
check
 
the
 
four
 
tyre
 
pressures when cold,
or
-

 
if

 
it
 
is
 
not
 
possible
 
to
 
check
 
the
 
tyre

 
pressures
 
at
 
the
 
time,
 
drive
 
carefully

 
at
 
reduced
 
speed.
This alert is also displayed when
one
  or   more   wheels   is   not   fitted  
with

  a   sensor   (for   example,   a  
space-saver

  or   steel   spare   wheel).
Go
  to   a   CITROËN   dealer   or   a   qualified  
workshop to

  have   the   system   checked  
or

, following the repair of a puncture, to
have the original wheel, equipped with
a
  sensor,   refitted.
Instruments and controls

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
43
SERVICE INDICATOR
This programmes service intervals according  to   the   use   of   the   vehicle.More than 1 000 miles/km before the
next service is due
Example:
  4   800   miles/km   remain  
before

  the   next   service   is   due.   When  
the ignition is switched on and for a
few

  seconds,   the   screen   shows:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance

  recorder   resumes   normal  
operation showing the total and trip
distances.
Less than 1 000 miles/km before the
next service is due
Each

  time   the   ignition   is   switched   on  
and for a few seconds, the spanner
flashes

  and   the   number   of   miles/
kilometres
  remaining   is   displayed:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance

  recorder   resumes   normal  
operation

  and   the   spanner   remains   on.  
This indicates that a service should be
carried

  out   shortly.
Service overdue
Operation
A
 

few   moments   after   the   ignition  
has been switched on, the spanner
indicating

  a   service   operation   comes  
on; the display for the total distance
recorder

  gives   (in   round   figures)   the  
distance

  remaining   before   the   next  
service.
The points at which a service is due
are

  calculated   from   the   last   indicator  
zero

  reset.
The point at which a service is due is
determined
  by   two   parameters:
-

the distance travelled,
-

 
the
  time   which   has   elapsed   since  
the

  last   service.
The
  distance   remaining   before   the  
next

  service   may   be   weighted   by  
the

  time   factor,   depending   on   the  
type

  of   driving. With the engine running the spanner
remains
  on   until   the   service   has   been  
carried

  out.
For BlueH
d i d iesel versions, this
alert
  is   also   accompanied   by   the   fixed  
illu

mination   of   the   Service   warning  
lamp,

  on   switching   on   the   ignition.
Each
  time   the   ignition   is  
switched on and for a few
seconds, the spanner
flashes

  and   the   excess  
distance

  is   displayed.
For BlueH
d i d iesel versions, the
spanner
  can   also   come   on   early,  
according the level of deterioration
of

  the   engine   oil.   Deterioration   of   the  
engine oil depends on the conditions of
use

  of   the   vehicle.
Instruments and controls
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
44
Trip recorder zero reset button
after this operation, if you wish to
disconnect   the   battery,   lock   the  
vehicle

  and   wait   for   at   least   five  
minutes,

  otherwise   the   zero   re-set   will  
not

 
be   registered.
Engine oil level indicator
depending on your vehicle's engine,
when the ignition is switched on, the
engine oil level is indicated for a few
seconds,
  after   the   service   information. Oil level correct
Low oil level
Flashing of "OIL",
linked
  with   the  
service

  warning   lamp,  
accompanied

  by   an  
audible

  signal   and   a   message   in   the  
screen, indicates a low oil level which
could

  damage   the   engine.
If   the   low   oil   level   is   confirmed   by   a  
check

  using   the   dipstick,   it   is   essential  
that

  the   level   is   topped   up.
Oil level gauge fault
Flashing of "OIL--"
indicates a
malfunction   of   the  
engine oil level
indicator
.   Contact   a   CITROËN   dealer  
or

  a   qualified   workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more   than   30   minutes.Dipstick
A
  =   maximum,   never   exceed  
this level as a surplus of oil
may

  damage   the   engine.
Contact a CITR o Ë n dealer
or   a   qualified   workshop  
without

  delay.
B  
=
 
minimum,
 
top
 
up
 
the
 
level
 
via

  the   oil   filler   cap,   using   the  
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
  and   controls.  
When the lighting
reaches

  the   minimum   (or  
maximum)

 
setting,   release   the   button  
then press it again to increase (or
reduce)

 
the
 
brightness.
a

s soon as the lighting is of the
required
 
brightness,   release   the   button.
Zero reset
Your CITROËN dealer or a qualified workshop  carries   out   this   operation  
after

  each   service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-

 
switch
  on   the   ignition.
The
  display   begins   a   countdown.
When the display shows "=0", release
the
  button;   the   spanner   disappears.
Instruments and controls