Citroen C4 RHD 2015 2.G Manual PDF

69 
CENTRAL LOCKING CONTROL
Locking
F
 
Press
  this   button   to   lock   the   vehicle.
The
 
red
 
indicator
 
lamp
 
in
 
the
 
button
 
comes

  on. If
 
the
 
vehicle
 
is
 
locked
 
from
 
the
 
outside,

  this   button   is   inactive.
F  
In
 
this
 
case,
 
use
 
the
 
remote
 
control

 
or
 
the
 
key
 
to
 
unlock
 
the vehicle or pull an interior
door

  handle   to   open   a   door.
If  
one
 
of
 
the
 
doors
 
is
 
open,
 
cen
-
tral
 
locking
 
from
 
the
 
inside
 
does
 
not

  take   place. Unlocking
F
 
Press
 
the
 
button
 
again
 
to
 
unlock
 
the
 
vehicle.
The
 
red
 
indicator
 
lamp
 
in
 
the
 
button
 
goes

  off.
ANTI-INTRUSION SECURITY
Operation
If
 
one
 
of
 
the
 
doors
 
or
 
the
 
boot
 
is
 
open,
 
the

 
automatic
 
central
 
locking
 
does
 
not
 
take

  place.
This
 
control

 
allows

 
the

 
simultaneous

 
locking

 
or

 
unlocking

 
of

 
the

 
doors

 
and

 
boot

 
from
 
inside
 
the
 
vehicle.
This 
system
 
allows
 
automatic
 
simulta
-
neous  
locking
 
of
 
the
 
doors
 
and
 
boot
 
as
 
soon

 
as
 
the
 
speed
 
of
 
the
 
vehicle
 
ex
-
ceeds   6   mph   (10   km/h).
Carrying long and voluminous
objects
If you  want  to  drive  with  the  boot open,
 you  should  press  the  central locking

 
button
 
to
 
lock
 
the
 
the
 
doors. Otherwise,

 
every
 
time
 
the
 
speed of

 
the
 
vehicle
 
exceeds
 
6
 
mph 
(10

 
km/h),
 
the
 
locks
 
will
 
rebound and

 
the
 
alerts
 
mentioned
 
above
 
will appear

.
Pressing the  central  locking  button  un -
locks   the   vehicle.
Above
 
6
 
mph
 
(10
 
km/h),
 
this
 
locking
 
is
 
temporary

.
This is signalled  by  the  sound  of  the locks
 rebounding,  accompanied  by  il -
lumination
 
of
 
this
 
symbol
 
in
 
the
 
instru
-
ment
 
panel,
 
an
 
audible
 
signal
 
and
 
the display

  of   an   alert   message.
4
ACCESS

70 
Emergency control
System allowing the  doors  to  be  locked  and
 unlocked  manually  in  the  event  of  
a

 
malfunction
 
of
 
the
 
central
 
locking
 
sys
-
tem
  or   battery   failure.
Locking the driver's door
F
 
Insert
 
the
 
key
 
in
 
the
 
door
 
lock,
 
then
 
turn

  it   to   the   rear.
You
 
can
 
also
 
apply
 
the
 
procedure
 
de
-
scribed
  for   the   passenger   doors.
Unlocking the driver's door
F
 
Insert
 
the
 
key
 
in
 
the
 
door
 
lock,
 
then
 
turn

  it   to   the   front. Locking the front and rear
passenger doors
Unlocking the front and rear
passenger doors
F
 
Pull
 
the
 
interior
 
door
 
opening
 
control.
F

 
Open
  the   doors.
F
 
On
 
the
 
rear
 
doors,
 
check
 
that
 
the
 
child

 
lock
 
is
 
not
 
on
 
(see
 
the
 
corre
-
sponding
  section).
F
 
Remove
 
the
 
black
 
cap,
 
located
 
on
 
the

  edge   of   the   door,   using   the   key.
F
 
Insert
 
the
 
key
 
in
 
the
 
socket
 
without
 
forcing

 
it,
 
then
 
without
 
turning
 
it,
 
move

 
the
 
latch
 
sideways
 
towards
 
the

  inside   of   the   door.
F
 
Remove
  the   key   and   refit   the   cap.
F
 
Close
 
the
 
doors
 
and
 
check
 
that
 
the
 
vehicle

 
has
 
locked
 
correctly
 
from
 
the

  outside.
Activation / Deactivation
You
 
can

 
activate

 
or

 
deactivate

 
this

 
func

-
tion
 
permanently.
F
 
With

 
the

 
ignition

 
on,

 
press

 
this

 
but

-
ton
 
until

 
an

 
audible

 
signal

 
starts

 
and

 
a

 
corresponding

 
message

 
is

 
dis

-
played.
the
 
state

 
of

 
the

 
system

 
stays

 
in

 
memory

 
when

 
switching
 
off
 
the
 
ignition.
4
ACCESS

71 * According  to   country.
ALARM*
System which protects  and  provides  a deterrent
 against  theft  and  break-ins.  It provides

 
the
 
following
 
types
 
of
 
monitoring.
-


exterior perimeter
The

 
system
 
checks
 
for
 
opening
 
of
 
the
 
vehicle.
The

 
alarm
 
is
 
triggered
 
if
 
anyone
 
tries
 
to
 
open

  a   door,   the   boot,   the   bonnet...
-

interior volumetric
The

 
system
 
checks
 
for
 
any
 
variation
 
in
 
the volume

  in   the   passenger   compartment.
The
 
alarm
 
is
 
triggered
 
if
 
anyone
 
breaks
 
a window

,  
enters
 
the
 
passenger
 
compart
-
ment
  or   moves   inside   the   vehicle.
-
tilt
The
 
system
 
checks
 
for
 
any
 
change
 
in
 
the

  attitude   of   the   vehicle.
The
 
alarm
 
is
 
triggered
 
if
 
the
 
vehicle
 
is
 
lifted,

  moved   or   knocked.
Self-protection function
The
 
system
 
checks
 
for
 
the
 
putting
 
out
 
of

  service   of   its   components.
The
 
alarm
 
is
 
triggered
 
if
 
the
 
battery
,  
the
 
central

 
control
 
or
 
the
 
siren
 
wiring
 
are
 
put

  out   of   service   or   damaged.
For
 
all
 
work
 
on
 
the
 
alarm
 
sys
-
tem,
 
contact
 
a
 
CITROËN
 
dealer
 
or

  a   qualified   workshop.
Locking the vehicle with full
alarm system
Activation
F 
Switch
 
of
f  
the
 
ignition
 
and
 
get
 
out
 
of
 
the

  vehicle.
F
 
Press
 
the
 
locking
 
button
 
on
 
the
 
re
-
mote
  control.
The
 
monitoring
 
system
 
is
 
active:
 
the
 
in
-
dicator
 
lamp
 
in
 
the
 
button
 
flashes
 
once
 
per

  second.
After
 
the
 
locking
 
button
 
on
 
the
 
remote
 
control

 
is
 
pressed,
 
the
 
exterior
 
perime
-
ter
 
monitoring
 
is
 
activated
 
after
 
a
 
delay
 
of

 
5
 
seconds
 
and
 
the
 
interior
 
volumetric
 
and

 
anti-tilt
 
monitoring
 
after
 
a
 
delay
 
of
 
45

  seconds. If
 
an
 
opening
 
(door
,  
boot...)
 
is not

 
closed
 
fully
,  
the
 
vehicle
 
is
 
not locked

 
but
 
the
 
exterior
 
perimeter monitoring

 
will
 
be
 
activated
 
af
-
ter  
a
 
delay
 
of
 
45
 
seconds
 
at
 
the same

 
time
 
as
 
the
 
interior
 
volu
-
metric   and   anti-tilt   monitoring.
Deactivation
F  
Press
 
the
 
unlocking
 
button
 
on
 
the
 
remote

  control.
The
 
alarm
 
system
 
is
 
deactivated:
 
the
 
indicator

  lamp   in   the   button   goes   off.
4
ACCESS

72 
Operating fault
When the ignition  is  switched  on,  fixed illumination
 of  the  indicator  lamp  in  the button

  indicates   a   fault   with   the   system.
Have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

  a   qualified   workshop.
Locking the vehicle with exterior
perimeter monitoring only
Deactivate the  interior  volumetric  and  anti-tilt
 monitoring  to  avoid  unwanted  
triggering

 
of
 
the
 
alarm
 
in
 
certain
 
cases
 
such

  as:
-
 
leaving
  a   pet   in   the   vehicle,
-
 
leaving
  a   window   partially   open,
-
 
washing
  your   vehicle,
-
 
changing
  a   wheel,
-
 
having
  your   vehicle   towed,
-
 
transport
  by   sea.
Deactivation of the interior
volumetric and anti-tilt monitoring
F
 
Switch
  off   the   ignition.
F
 
Within
 
ten
 
seconds,
 
press
 
the
 
but
-
ton
 
until
 
the
 
indicator
 
lamp
 
is
 
on
 
continuously

.
F
 
Get
  out   of   the   vehicle.
F
 
Press
 
the
 
locking
 
button
 
on
 
the
 
re
-
mote
  control   immediately. The
 
exterior
 
perimeter
 
monitoring
 
alone
 
is

 
activated:
 
the
 
indicator
 
lamp
 
in
 
the
 button
  flashes   once   per   second.
To  
be
 
ef
fective,  
this
 
deactivation
 
must

 
be
 
carried
 
out
 
each
 
time
 
the

  ignition   is   switched   off.
Reactivation of the interior
volumetric and anti-tilt monitoring
F
 
Press
 
the
 
unlocking
 
button
 
on
 
the
 
remote

 
control
 
to
 
deactivate
 
the
 
ex
-
terior
  perimeter   monitoring.
F
 
Press
 
the
 
locking
 
button
 
on
 
the
 
re
-
mote
 
control
 
to
 
activate
 
all
 
the
 
moni
-
toring
  functions.
The
 
indicator
 
lamp
 
in
 
the
 
button
 
again
 
flashes

  once   per   second.
Triggering of the alarm
This is indicated  by  sounding  of  the  si -
ren  and  flashing  of  the  direction  indica -
tors
  for   thirty   seconds.
The
 
monitoring
 
functions
 
remain
 
ac
-
tive
 
until
 
the
 
alarm
 
has
 
been
 
triggered
 
eleven

  times   in   succession.
When
 
the
 
vehicle
 
is
 
unlocked
 
using
 
the
 
remote

 
control,
 
rapid
 
flashing
 
of
 
the
 
in
-
dicator
 
lamp
 
in
 
the
 
button
 
informs
 
you
 
that

 
the
 
alarm
 
was
 
triggered
 
during
 
your
 
absence.

 
When
 
the
 
ignition
 
is
 
switched
 
on,

  this   flashing   stops   immediately.
Failure of the remote control
To deactivate the monitoring functions:
F  
unlock
 
the
 
vehicle
 
using
 
the
 
key
 
in
 
the

  driver's   door   lock,
F
 
open
 
the
 
door;
 
the
 
alarm
 
is
 
triggered,
F

 
switch
 
on
 
the
 
ignition;
 
the
 
alarm stops;

 
the
 
indicator
 
lamp
 
in
 
the
 
button goes

  off.
Locking the vehicle without
activating the alarm
F Lock or  deadlock  the  vehicle  using  the
  key   in   the   driver's   door   lock.
4
ACCESS

73 
DOORS
Opening
F After unlocking  the  vehicle  com -
pletely  using  the  remote  control  or  
the

  key,   pull   the   door   handle.
From outside
When  
the
 
selective
 
unlocking
 
is
 
activated,

 
the
 
first
 
press
 
of
 
the
 
remote

 
control
 
unlocking
 
button
 
permits

 
unlocking
 
of
 
the
 
driver's
 
door

  only. F

Pull the
interior control lever of a
front  
door;
 
this
 
unlocks
 
the
 
vehicle
 
completely

.
From inside
With  
the
 
selective
 
unlocking
 
ac
-
tivated:
-
 
opening
 
the
 
driver's
 
door
 
un
-
locks
 
the
 
driver's
 
door
 
only
 
(if
 
the

 
vehicle
 
has
 
not
 
already
 
been

  completely   unlocked).
-
 
opening
 
the
 
passenger's
 
door

 
unlocks
 
the
 
rest
 
of
 
the
 
vehicle.
The

 
interior
 
door
 
controls
 
do
 
not operate when the vehicle is
deadlocked.
Closing
When a door is not closed correctly:
-  
when the engine is run
-
ning,
 
this
 
warning
 
lamp
 
comes

 
on,
 
accompanied
 
by
 
an

 
alert
 
message
 
for
 
a
 
few
 
seconds,
-

 
when the vehicle is moving
 
(speed
 
higher

 
than
 
6
  mph  
(10
  km/h)),  
this
 
warning

 
lamp
 
comes
 
on,
 
accom
-
panied
 
by
 
an
 
alert
 
message
 
for
 
a
 

few

  seconds.
4
ACCESS

74 
BOOT
Opening
F After unlocking  the  boot  or  the  ve -
hicle  using  the  remote  control  or  the  
key

,  
press
 
the
 
opening
 
control,
 
then
 
raise

  the   tailgate.
Closing
F Lower the  tailgate  using  the  interior  grab
  handle.
F
 
If
 
necessary
,  
press
 
down
 
on
 
the
 
tail
-
gate
  to   fully   close   it.
Tailgate release
System allowing the  mechanical  unlock -
ing  of  the  boot  in  the  event  of  a  battery  or central

  locking   system   malfunction.
Unlocking
F
 
Fold
 
back
 
the
 
rear
 
seats
 
to
 
gain
 
access

 
to
 
the
 
lock
 
from
 
inside
 
the
 
boot.
F

 
Insert
 
a
 
small
 
screwdriver
 
into
 
hole
 
A

of
  the   lock   to   unlock   the   tailgate.
F
 
Move
  the   latch   to   the   left.
If
 
the
 
tailgate
 
is
 
not
 
closed
 
correctly:
-
 
when

the engine is running,
this
 
warning

 
lamp

 
comes

 
on, accompanied

 
by

 
the

 
display of

 
an

 
alert

 
message

 
for

 
a

 
few seconds,
-

 
when the vehicle is moving

 
(speed above

 
6

 
mph
 
(10

 
km/h)),
 
this

 
warn

-
ing
 
lamp

 
comes

 
on,

 
accompanied

 
by an

 
audible

 
signal

 
and

 
the

 
display

 
of an

 
alert
 
message
 
for
 
a
 
few
 
seconds. Locking after closing
If
 
the
 
fault
 
persists
 
after
 
closing
 
again,
 
the

  boot   will   remain   locked.
4
ACCESS

75 
ELECTRIC WINDOWS
Fitted with a  safety  anti-pinch  system  and
 a  deactivation  system  for  the  rear  
controls.
1.


Driver's electric window
.
2.

Passenger's electric window
.
3.

Rear right electric window
.
4.

Rear left electric window
.
5.

Deactivation of the rear electric
window controls. The

 
electric
 
window
 
controls
 
remain

 
operational
 
for
 
approxi
-
mately
 
45
 
seconds
 
after
 
the
 
i

 
gnition
 
is
 
switched
 
of
f  
or
 
until
 
the

 
vehicle
 
is
 
locked
 
after
 
a
 
door
 
is

  opened.
If
 
one
 
of
 
the
 
passenger
 
windows
 
cannot

 
be
 
operated
 
from
 
the
 
driver's

 
door
 
control
 
panel,
 
carry
 
out

 
the
 
operation
 
from
 
the
 
con
-
trol
 
panel
 
of
 
the
 
passenger
 
door
 
concerned,

  and   vice   versa.After
 
approximately
 
ten
 
con
-
secutive  complete  opening/clos -
ing  movements  of  the  window ,  a  
protection

 
function
 
is
 
activated
 
which

 
only
 
authorises
 
closing
 
of
 
the

 
window
 
to
 
prevent
 
damage
 
to

  the   electric   window   motor.
Once the window  is  closed,  the  con -
trols  will  become  available  again  af -
ter
  approximately   40   minutes.
If the window  cannot  be  closed  (for example,
 in  the  presence  of  ice), once

  the   window   has   lowered:
F
 
press
 
and
 
hold
 
the
 
control
 
until

  the   window   opens   fully,
F
 
then
 
pull
 
the
 
control
 
immedi
-
ately
 
and
 
hold
 
it
 
until
 
the
 
win
-
dow
  closes,
F
 
continue
 
to
 
hold
 
the
 
control for

 
approximately
 
one
 
second after

  the   window   has   closed.
The safety anti-pinch func-
tion is not operational during
these operations.
There
 
are
 
two
 
options:
-
 
manual mode
F

 
Press

 
or

 
pull

 
the

 
control

 
gently

.
 
The window

 
stops

 
when

 
the

 
control

 
is released.
-

 
automatic mode
F

 
Press

 
or

 
pull

 
the

 
control

 
firmly

.
 
The

 
window

 
opens

 
or

 
closes

 
fully

 
when

 
the
 
control
 
is
 
released.
F
 
Pressing

 
the

 
control

 
again

 
stops

 
the

 
movement
 
of
 
the
 
window.
Safety anti-pinch
When 
the
 
window
 
rises
 
and
 
meets
 
an
 
obstacle,

 
it
 
stops
 
and
 
partially
 
lowers
 
again.
One-touch electric windows
4
ACCESS

76 
Reinitialisation
After 
reconnecting
 
the
 
battery
 
or
 
a
 
fault,
 
you

 
must
 
be
 
reinitialise
 
the
 
operation
 
of
 
the

 
electric
 
windows.
 
For
 
each
 
of
 
the
 
control

 
switches
 
on
 
the
 
driver's
 
side
 
control

  panel:
F
 
pull
 
the
 
control
 
until
 
the
 
window
 
stops,
F

 
release
 
the
 
control
 
and
 
pull
 
it
 
again
 
until

  the   window   closes   fully,
F
 
continue
 
to
 
hold
 
the
 
control
 
for
 
ap
-
proximately
 
one
 
second
 
after
 
the
 
window

  has   closed,
F

press the control to lower the win
-
dow
 
automatically
 
to
 
the
 
low
 
posi
-
tion,
F
 
when
 
the
 
window
 
has
 
reached
 
the
 
low

 
position,
 
press
 
the
 
control
 
again
 
for

  approximately   one   second.
The safety anti-pinch function is not
operational during these operations. F
 
For
 
the
 
safety
 
of
 
your
 
children,
 
press
 
control 5

 
to
 
deactivate
 
the
 
rear
 
elec
-
tric
 
window
 
controls
 
regardless
 
of
 
their

  position.
Indicator
 
lamp
 
on,
 
the
 
rear
 
controls
 
are
 
deactivated.
Indicator

 
lamp
 
of
f,  
the
 
rear
 
controls
 
are
 
activated.
Deactivation of the rear electric
window controlsAlways remove the  key  from  the  ignition
 when  leaving  the  vehi -
cle,
  even   for   a   short   time.
If
 
an
 
obstacle
 
is
 
encountered
 
during

 
operation
 
of
 
the
 
electric
 
windows,

 
you
 
must
 
reverse
 
the
 
movement

 
of
 
the
 
window
.  
T
o  
do

 
this,
 
press
 
the
 
control
 
con
-
cerned.
When
 
the
 
driver
 
operates
 
the
 
controls

 
for
 
the
 
passengers'
 
electric

 
windows,
 
they
 
must
 
en
-
sure
 
that
 
nothing
 
is
 
preventing
 
the

  windows   closing   correctly.
The
 
driver
 
must
 
ensure
 
that
 
the
 
passengers

 
use
 
the
 
electric
 
win
-
dows
  correctly.
Be
 
aware
 
of
 
children
 
when
 
oper
-
ating
  the   windows.
4
ACCESS

77 
PANORAMIC SUNROOF
Your vehicle is  fitted  with  a  tinted  glass  panoramic
 sunroof  which  increases  
the

 
light
 
and
 
visibility
 
in
 
the
 
passenger
 
compartment.

 
Its
 
electric
 
blind
 
helps
 
control

 
the
 
temperature
 
in
 
the
 
passen
-
ger
  compartment.
Electric blind
Opening
Turn  
the
 
dial
 
to
 
the
 
left
 
(four
 
possible
 
settings).
Closing
Return

  the   dial   to   the   initial   position.Safety anti-pinch
If
 
the
 
blind
 
encounters
 
an
 
obstacle
 
dur
-
ing  
closing,
 
it
 
stops
 
and
 
partially
 
opens
 
again.
If

 the  blind  fails  to  close  at  a  second  at -
tempt,  it  may  be  necessary  to  force  the  
closing

 
of
 
the
 
blind
 
using
 
the
 
reinitiali
-
sation
  procedure.
The
 
blind
 
is
 
controlled
 
electrically
 
by
 
a
 
rotary

  dial. In  
the
 
event
 
of
 
contact
 
during operation

 
of
 
the
 
blind,
 
you
 
must reverse

 
its
 
movement.
 
T
o  
do
 
this, turn

  the   dial.
When  the  driver  operates  the  dial,
 they  must  ensure  that  noth -
ing
 
prevents
 
the
 
blind
 
from
 
clos
-
ing
  correctly.
The
 
driver
 
must
 
ensure
 
that
 
the
 
passengers

 
use
 
the
 
blin
d  
cor
-
rectly.
Be
 
aware
 
of
 
children
 
during
 
opera
-
tion
  of   the   blind.
Reinitialising the system
Following reconnection of  the  battery ,  or
 in  the  event  of  a  malfunction  in  its  
operation,

 
it
 
may
 
be
 
necessary
 
to
 
reini
-
tialise
  the   system:
F
 
turn
 
the
 
dial
 
to
 
the
 
fully
 
closed
 
posi
-
tion,
F
 
then
 
immediately
 
press
 
the
 
dial,
 
clos
-
ing
  starts   after   about   10   seconds,
F
 
maintain
 
pressure
 
on
 
the
 
dial
 
until
 
the

  blind   has   fully   closed.
The anti-pinch function is inopera-
tive during these operations.
If
 
the

 
position

 
of

 
the

 
blind

 
does

 
not

 
agree

 
with

 
the

 
position

 
indicated

 
by

 
the

 
dial,

 
press

 
the

 
dial

 
to

 
open

 
the

 
blind

 
to

 
this

 
position.
4
ACCESS

55
78 
LIGHTING CONTROLS
System for selection  and  control  of  the  various
 front  and  rear  lamps  providing  
the

  vehicle's   lighting.
Main lighting
The various front  and  rear  lamps  of  the vehicle
 are  designed  to  adapt  the  driver's visibility

 
progressively
 
according
 
to
 
the climatic

  conditions:
-
 
sidelamps,
  to   be   seen,
-
 
dipped
 
beam
 
headlamps
 
to
 
see
 
without

  dazzling   other   drivers,
-
 
main beam  headlamps  to  see  clearly when
  the   road   is   clear.
Additional lighting
Other lamps are  provided  to  meet  the  requirements
 of  particular  driving  con -
ditions:
-
 
rear
  foglamps,
-
 front

 
foglamps
 
with
 
cornering
 
lighting,
-

 
directional
 
headlamps
 
for
 
improved
 
visibility

  when   cornering,
-
 
daytime
 
running
 
lamps
 
to
 
be
 
more
 
visible

  during   the   day,
-
 guide-me-home

 
and
 
welcome
 
light
-
ing
 
to
 
facilitate
 
access
 
to
 
the
 
vehicle,
-

 
parking
 
lamps
 
as
 
vehicle
 
position
 
markers.
Programming
The setting of  some  functions  can  be  adjusted:
-
 
daytime
  running   lamps,
-
 automatic

 
illumination
 
of
 
headlamps,
-

 
guide-me-home
  lighting,
-
 
welcome
  lighting,
-
 
directional
  lighting.
In
 
some

 
weather

 
conditions

 
(e.g. low

 
temperature

 
or

 
humidity),

 
the presence

 
of

 
misting

 
on

 
the

 
inter

-
nal
 
surface

 
of

 
the

 
glass

 
of

 
the headlamps

 
and

 
rear

 
lamps

 
is

 
nor

-
mal;
 
it

 
disappears

 
after

 
the

 
lamps have

 
been
 
on
 
for
 
a
 
few
 
minutes.
VISIBILITY