FIAT 500L LIVING 2014 2.G Owners Manual

USE OF THE "Fix&Go Automatic"KIT
For kit usage see paragraph "Fix&Go Automatic kit"
in the Owner Handbook in the section concerning
version
.
REPLACING A WHEELGENERAL INSTRUCTIONS
The car is equipped with the "Fix&Go Automatic
Kit": see the paragraph “Fix&Go Automatic Kit” for
how to use this device.
As an alternative to the “Fix&Go Automatic Kit” the
car may be equipped with a space-saver wheel: see
the instructions on the following pages for changing
the wheel.
WARNING
The space-saver wheel (for
versions/markets where provided) is
specific to your car, do not use it on other
models, or use the space-saver wheel of other
models on your car.The space-saver wheel must
only be used in the event of emergency. It must
only be used for the distance necessary to reach
a service point and the car speed must not
exceed 80 km/h.The space-saver wheel has an
orange label that summarises the main cautions
for use and limitations. Never remove or cover
the label.The following information is provided
in four languages on the label: "Important! For
temporary use only! 80 km/h max! Replace with
a standard wheel as soon as possible. Never
cover this indication." Never apply a wheel cap
on a space-saver wheel.
fig. 24
F0Y0011
317

WARNING
Alert other drivers that the car is
stationary in compliance with local
regulations: hazard warning lights, warning
triangle, etc . Any passengers on board should
leave the car, especially if it is heavily laden.
Passengers should stay away from on-coming
traffic while the wheel is being changed. If you
are on a slope or uneven surface, place the
wedge provided under the wheels (see the
instructions on the next pages).
WARNING
The vehicle's driving characteristics will
be modified with the space-saver wheel
fitted. Avoid violent acceleration and braking,
abrupt steering and fast cornering.The overall
duration of the space-saver wheel is of about
3000 km, after which the relevant tyre must be
replaced with another one of the same type.
Never install a standard tyre on a rim that is
designed for use with a space-saver wheel. Have
the wheel repaired and refitted as soon as
possible. Using two or more small space-saver
wheels at the same time is forbidden. Do not
grease the threads of the stud bolts before
fitting them: they might slip out .
WARNING
The jack shall only be used for raising
the car model it has been supplied with.
Never use the jack for other purposes, such as
raising other car models. Never use the jack for
repair operations under the vehicle. Incorrectly
positioning of the jack may cause the car to fall.
Do not use the jack for loads higher than the
one shown on its label.The space-saver wheel
cannot be fitted with snow chains. If a front
(drive) tyre is punctured and chains are needed,
use a standard wheel from the rear axle and
install the space-saver wheel on the rear axle. In
this way, with two normal drive wheels at the
front axle, it is possible to use snow chains.
WARNING
Incorrectly fitting the wheel cap may
cause it to fall off when the vehicle is in
motion. Never tamper with the inflation valve.
Never introduce tools of any kind between rim
and tyre. Check tyre and space-saver wheel
pressures regularly, complying with the values
given in the “Wheels” paragraph.
318

JACK
Please note that:
❒the jack weight is 1.76 kg;
❒the jack requires no adjustment;
❒the jack cannot be repaired and in the event of a
fault it must be replaced by another original one;
❒no tool other than its cranking device may be fitted
on the jack.
WHEEL REPLACEMENT PROCEDURE
To change a wheel, proceed as follows:
❒stop the car in a position that is not dangerous for
oncoming traffic where you can change the wheel
safely. The ground should be flat if possible, and
sufficiently firm;
❒switch off the engine, pull up the handbrake and
engage the 1
stgear or reverse. Wear the reflective
safety jacket (compulsory by law) before getting
out of the car;
❒5-seater versions:open the luggage compartment,
grab handle A fig. 25 and raise platform B for the
"Cargo Magic Space" upwards, keeping it with one
hand. Then take the tool bag fig. 26. Movement of
the "Cargo Magic Space" load platform must take
place in a central position relative to the luggage
compartment.
❒
7-seater versions:open the luggage compartment
and take the tool bag fig. 27;❒the following can be found in the tool box: tow
hook, screwdriver, jack, wedge, spanner for wheel
stud bolts/jack operation, Allen key for sun roof
emergency operation (for versions/markets, where
provided), adaptor for emergency refuelling;
fig. 25
F0Y0359
fig. 26
F0Y0351
319

❒raise flap A fig. 28 located on the luggage
compartment mat, take spanner B fig. 29 from the
tool bag and fit it on device C;
❒rotate spanner B fig. 29 anticlockwise in order to
undo the space-saver wheel support locking bolt,
allowing the latter to be lowered;❒use the spanner to remove the wheel from the car
fig. 30;
fig. 27
F0Y0352
fig. 28
F0Y0383
C
fig. 29
F0Y0355
fig. 30
F0Y0356
320

❒rotate device D fig. 31 in order to detach the
space-saver wheel from fixing support E;
❒then take the space-saver wheel fig. 32;❒take the spanner A fig. 33 and loosen the fixing
stud bolts by about one turn. For versions with
alloy rims, shake the car to facilitate detachment of
the rim from the wheel hub;
❒take the wedge A from the tool box and open it as
shown in the diagram in fig. 34;
fig. 31
F0Y0357
fig. 32
F0Y0358
fig. 33
F0Y0093
fig. 34
F0Y0211
321

❒place the wedge behind the wheel diagonally
opposite the one to be replaced (see fig. 35) to
prevent the car from moving when it is raised;
❒position the jack under the car, near the wheel to
be changed;
❒insert the spanner A to extend the jack until the
top of the jack B fig. 36 fits correctly into the side
member C (next to the mark
on the side
member itself );
❒alert any bystander that the car is about to be
raised; all persons should be kept away from the
car and nobody must touch it until it has been
lowered;
❒fit handle D fig. 36 into the housing in device A,
operate the jack and raise the car until the wheel is
a few centimetres from the ground;❒remove the wheel cap after unscrewing the four
fixing stud bolts and finally undo the fifth stud bolt
and extract the wheel (only for versions with
wheel caps fixed by stud bolts);
❒make sure the contact surfaces between space-
saver wheel and hub are clean and free from
impurities so that the fixing stud bolts will not
come loose;
❒fit the space-saver wheel by inserting the first stud
bolt for two threads into the hole closest to the
valve;
❒tighten the stud bolt by some threads and proceed
in the same way for the others;
❒take the spanner A and fully tighten the fixing stud
bolts;
❒operate the jack handle D to lower the car. Then
extract the jack;
fig. 35
F0Y0212
fig. 36
F0Y0014
322

❒use the spanner A to fully tighten the stud bolts in
a criss-cross fashion as per the numerical sequence
illustrated in fig. 37;
❒when replacing a wheel with alloy rim it is advisable
to place it with the esthetic part facing upwards.
Restore the standard wheel as soon as possible,
because, once placed in the associated compartment,
the luggage compartment load platform is rendered
uneven as the standard wheel is larger than the
space-saver wheel.
When the operation is over, proceed as follows:
❒restart device A fig. 38 on fixing support B;
❒insert spanner C fig. 39 on device D and rotate it
clockwise in order to tighten the space-saver
wheel support locking bolt. The device is correctly
attached when the yellow strip appears in window
E on the hole;❒fit the punctured tyre in the dedicated bag A fig.
40.
fig. 37
F0Y0013
fig. 38
F0Y0360
fig. 39
F0Y0361
323

WARNING
At the end of the operation of
raising/locking the space-saver wheel
device, the spanner must be extracted, taking
care NOT to turn it in the wrong direction to
facilitate the extraction of the spanner itself, so
as to prevent the attachment device from being
released and the lack of safe restraint .Punctured tyre position
5-seater versions
Place the punctured tyre in the luggage
compartment.
7-seater versions
❒With third row of rear seats folded: place the
punctured tyre in the luggage compartment, above
the backrests.
❒With third row of rear seats not folded: remove the
luggage-covering curtain (which must be positioned
in front of second row of seats) then place the
punctured tyre in the luggage compartment,
positioning it as shown in fig. 41 (wheel hub facing
the inside of the passenger compartment in order
to prevent the wheel from falling when closing the
tailgate).
fig. 40
F0Y0367
fig. 41
F0Y0368
324

REFITTING THE STANDARD WHEEL
Following the procedure described previously, raise
the car and remove the space-saver wheel.
Versions with steel rims
Proceed as follows:
❒make sure the contact surfaces between standard
wheel and hub are clean and free from impurities
so that the fixing stud bolts will not come loose;
❒fit the standard wheel inserting the 5 stud bolts
into the holes;
❒press-fit the wheel cap, aligning the special splining
(on the cap) with the inflation valve;
❒using the spanner provided, tighten the fixing stud
bolts;
❒lower the car and remove the jack;
❒using the spanner provided, fully tighten the stud
bolts in the sequence shown previously.Versions with alloy rims
Proceed as follows:
❒insert the wheel on the hub and using the spanner
provided tighten the stud bolts;
❒lower the car and remove the jack;
❒using the spanner provided, fully tighten the 5 stud
bolts in the sequence shown;
❒reinstall the hub cap, taking care to position the
three plastic pins in the dedicated seats on the
wheel. Slightly press the cap to prevent any damage
to the plastic pins.
IMPORTANT If it is not fitted correctly, the hub cap
may detach when the car is running.
325

At the end of the operation
Proceed as follows:
❒place the space-saver wheel in the luggage
compartment;
❒place the jack and the other tools in the tool bag;
❒place the bag, complete with the tools, in the
luggage compartment, then secure it with the
suitable belts;
❒correctly reposition the luggage compartment mat.
REPLACING INTERIOR BULBSTHIRD ROW REAR SEAT ROOF LIGHT
(for versions/markets, where provided)
Type of bulb: C5W
Power:5W
To replace the bulb, proceed as follows:
❒operate in the point shown by the arrows and
remove roof light A fig. 42;
❒open the flap C fig. 43 and replace the bulb B
releasing it from the side contacts;
❒Insert the new bulb and make sure that it is
correctly clamped between the contacts.
❒refit the roof light A fig. 42 by inserting it in its
correct position, firstly on one side and then
pressing on the other until it clicks into place.
fig. 42
F0Y0152
326