tire pressure FORD MUSTANG 1969 Volume One Chassis

02-01-03
Brakes

02-01-03

vacuum system is operating, the pedal

will tend to fall away under foot pres-

sure and less pressure will be required

to hold the pedal in the applied posi-

tion. If no action is felt, the vacuum

booster system is not functioning.

If the brake pedal movement feels

spongy, bleed the hydraulic system to

remove air from the system. Refer to

Hydraulic System Bleeding, Part 1,

Section 2.

VACUUM TESTS—VACUUM

RELEASE PARKING BRAKES

Visually check the operation of the

brake linkage as the brake pedal is

depressed. Then, check the operation

of the brake linkage when the manual

release lever is activiated. These

checks should indicate whether the

manual parking brake control linkage

is operating properly or requires re-

pair or adjustment due to inability of

the parking brake to hold against

moderate vehicle movement. Perform

tests of the parking brake system and

controls after making certain the link-

age and manual controls operate

properly.

When testing a parking brake vacu-

um release system, a minimum of 10

inches of vacuum (Hg.) should be

available at all points where vacuum is

applied. This can be checked with a

Rotunda Fuel Pump Tester Gauge

(ARE345) and two Distributor Tester

hose adapters (Marked Q) connected

together with a coupling. This allows

the Fuel Pump Tester Gauge hose to
be adapted to any other vacuum hose

or rubber connector in the vacuum

systems.

Failure to maintain 10 inches of

vacuum (Hg.) during vacuum system

tests could be caused by a loose hose

connection, resulting in a vacuum

leak. When checking for vacuum be-

tween two points, trace the hose along

the entire routing to be sure it is not

crossed with another hose and con-

nected to the wrong connection.

All of the vacuum parking brake

control checks are to be performed

with the engine running at idle speed.

Leaks in the parking brake hoses or

a disconnected or improperly con-

nected hose can usually be found by

listening for a hissing sound along the

hose routings. Under no circumstances

should air pressure be applied to the

vacuum system as the actuator dia-

phragm in the parking brake vacuum

motor may be damaged.

1.
Start the engine and run it at

idle speed. With the transmission shift

control in neutral, depress the parking

brake pedal to apply the parking

brake. Move the transmission shift

control to D range and observe the

parking brake pedal to see that the

pedal moves upward and the parking

brake releases. If the parking brake

releases, the parking brake vacuum

control is working properly.

2.
If the parking brake does not re-

lease, test for vacuum at the steering

column neutral switch port in the

junction block, vacuum lines and the

parking brake release vacuum motor.

Use the Rotunda Vacuum and Fuel
Pump Tester 345. This can be accom-

plished by removing the hose from

each component and attaching it to

the vacuum gauge. Connect two dis-

tributor tester vacuum hose adapters

together with a coupling as a connec-

tor to attach the gauge. A minimum

of ten inches of vacuum is required to

actuate the parking brake vacuum

motor. Do not remove any of the vac-

uum hoses from the junction block

unless the junction block is being re-

placed, as the plastic nipples are thin

and very brittle and damage may re-

sult. If a minimum reading is not

present when checking each of the

aforementioned components, they

must be replaced.

ROAD TEST

A road test should be conducted

only when the operator is sure the

brakes will stop the vehicle.

If the road test reveals one or more

problem conditions, correct all mal-

functions of the vacuum system, brake

booster and hydraulic system prior to

removing brake drums, brake calipers,

brake shoes and linings or backing

plates.

ANTI-SKID CONTROL

SYSTEM TESTS

No adjustments or repairs are to be

performed on the skid control system.

Damaged or worn parts are to be re-

placed.

Refer to Ford Car and Truck Diag-

nosis Manual for Testing procedures.

COMMON ADJUSTMENTS AND REPAIRS

PARKING BRAKE LINKAGE

ADJUSTMENT

FORD, MERCURY, METEOR,

FAIRLANE, MONTEGO,

FALCON, MUSTANG

AND COUGAR

Check the parking brake cables

when the brakes are fully released. If1

the cables are loose, adjust them as

follows:

1.
Fully release the parking brake

pedal by pulling the release lever.

2.
Depress the parking brake pedal

until it is engaged in the first notch of

the control. On a vacuum release

brake, the first notch will be approxi-

mately two inches of pedal travel.

3.
Raise the vehicle. With the

transmission in neutral, turn the ad-

justing nut forward against the equal-

izer (Figs. 3 and 4) until there is 100
L.H. REAR WHEEL CABLE -2A809> 2A791 (2 REQUIRED)

EQUALIZER-TO-ACTUATOR CABLE-2A815

R.H. REAR WHEEL CABLE-2A635

ADJUSTING NUT-2A812

H 1537-C

FIG. 3—Parking Brake Adjustment—Ford, Mercury, Meteor,

Thunderbird and Continental Mark IIIprocarmanuals.com

02-01-06

Brakes

02-01-06

side.
Refill the master cylinder reser-

voir after each wheel cylinder is bled

and install the master cylinder cover

and gasket. Be sure the diaphragm

type gasket is properly positioned in

the master cylinder cover. When the

bleeding operation is completed, the

fluid level should be filled to within

1/4 inch of the top of the reservoirs.

7. If the primary (front brake) sys-

tem is to be bled. Repeat steps 2

through 6 at the right front brake cal-

iper or cylinder and ending at the left

front brake caliper or cylinder.

8. On disc brake equipped models

be sure that the front brake pistons

are returned to their normal positions

and that the shoe and lining assem-

blies are properly seated by depressing

the brake pedal several times until

normal pedal travel is established.

9. Centralize the pressure differen-

tial valve. Refer to the Centralizing

the Pressure Differential Valve proce-

dures which follow.

PRESSURE BLEEDING

The Lincoln Continental hydraulic

brake system is to be bled only with

pressure bleeding equipment.

Bleed the longest lines first. The

bleeder tank should contain enough

new Ford Brake Fluid to complete the

bleeding operation. Use Ford Brake

Fluid — Extra Heavy Duty — Part

Number C6AZ-19542-A (ESA-

M6C25-A) or equivalent for all brake

applications. The brake fluid is col-

ored blue for identification purposes.

Do not mix low temperature brake

fluid with the specified brake fluid

during the bleeding operations. Never

re-use brake fluid that has been

drained from the hydraulic system.

The tank should be charged with ap-

proximately 10 to 30 pounds of air

pressure. Never exceed 50 pounds

pressure.

1.
Clean all dirt from the master

cylinder reservoir cover.

2.
Remove the master cylinder res-

ervoir cover and rubber gasket, and

fill the master cylinder reservoir with

the specified brake fluid. Install the

pressure bleeder adapter tool to the

master cylinder, and attach the bleed-

er tank hose to the fittng on the

adapter.

Master cylinder pressure bleeder

adapter tools can be obtained from

the various manufacturers of pressure

bleeding equipment. Follow the in-

structions of the manufacturer when

installing the adapter.

3.
If the master cylinder is

equipped with a bleed screw, loosen
the bleed screw and bleed the master

cylinder until the fluid is free of air

bubbles; then, tighten the bleed screw.

Do not use the secondary piston stop

screw, located on the bottom of the

master cylinder, to bleed the master

cylinder.

4.
If the rear wheel cylinders, the

secondary brake system, are to be

bled, position a 3/8 inch box wrench

(Fig. 9) on the bleeder fitting on the

right rear brake wheel cylinder. At-

tach a bleeder tube to the bleeder fit-

ting. The end of the tube should fit

snugly around the bleeder fitting.

5. Open the valve on the bleeder

tank to admit pressurized brake fluid

to the master cylinder reservoir.

6. Submerge the free end of the

tube in a container partially filled with

clean brake fluid, and loosen the

bleeder fitting.

7.
When air bubbles cease to ap-

pear in the fluid at the submerged end

of the bleeder tube, close the bleeder

fitting and remove the tube.

8. Repeat steps 3 through 7 at the

left rear wheel cylinder.

9. If the vehicle is equipped with

disc brakes, repeat steps 4 through 7,

starting at the right front disc caliper

and ending at the left front disc cali-

per.

On Lincoln Continental models the

front wheel and tire assemblies must
be removed to gain access to the

bleeder fittings on the calipers. Also

on Lincoln Continental models the

metering valve release rod must be

pulled outward and held a minimum

of 1/16 inch (Fig. 10) while bleeding

the primary brake system.

10.
If the vehicle contains drum-

type front brakes and the primary

(front) brake system is to be bled, re-

peat steps 4 through 7, starting at the

right front wheel cylinder ending at

the left front wheel cylinder.

11.
When the bleeding operation is

completed, close the bleeder tank

valve and remove the tank hose from

the adapter fitting.

12.
On disc brake equipped ve-

hicles,
be sure that the front brake

pistons are returned to their normal

positions and that the shoe and lining

assemblies are properly seated by dep-

ressing the brake pedal several times

until normal pedal travel is esta-

blished.

13.
Remove the Pressure Bleeder

Adapter Tool. Fill the master cylinder

reservoirs to within 1/4 inch of the

top.
Install the master cylinder cover

and gasket. Be sure the Diaphragm

type gasket is properly positioned in

the master cylinder cover.

14.
Centralize the pressure differen-

tial valve as follows.

METERING VALVE

BLEEDER RETAINER

SEE

VIEW A

RELEASE ROD

FIG. 10—Disc Brake Metering Valve—Lincoln Continental
HI 644-Aprocarmanuals.com

02-01-07
Brakes

02-01-07

CENTRALIZING THE

PRESSURE DIFFERENTIAL

VALVE

After a failure of the primary (front

brake) or secondary (rear brake) sys-

tem has been repaired and bled, the

dual-brake warning light will usually

continue to be illuminated due to the

pressure differential valve remaining in

the off-center position.

To centralize the pressure differen-

tial valve and turn off the warning
light after a repair operation, a pres-

sure differential or unbalance condi-

tion must be created in the opposite

brake system from the one that was

repaired or bled last.

1.
Turn the ignition switch to the

ACC or ON position. Loosen the dif-

ferential valve assembly brake tube

nut at the outlet port on the opposite

side of the brake system that was

wheel balanced, repaired and/or bled

last. Depress the brake pedal slowly to

build line pressure until the pressure
differential valve is moved to a cen-

tralized position and the brake warn-

ing light goes out; then, immediately

tighten the outlet port tube nut.

2.
Check the fluid level in the mas-

ter cylinder reservoirs and fill them to

within 1/4 inch of the top with the

specified brake fluid, if necessary.

3.
Turn the ignition switch to the

OFF position.

4.
Before driving the vehicle, check

the operation of the brakes and be

sure that a firm pedal is obtained.

CLEANING AND INSPECTION

DISC BRAKES

1.
Remove the wheel and tire and

the shoe and lining assemblies as out-

lined in Part 2-2, Section 2.

2.
On all models except Lincoln

Continental, make thickness measure-

ments with a micrometer across the

thinnest section of the shoe and lining.

If the assembly has worn to a thick-

ness of 0.230-inch (shoe and lining to-

gether) or 0.030-inch (lining material

only) at any one of three measuring

locations or if there is more than

0.125 taper from end to end or if lin-

ing shows evidence of brake fluid con-

tamination, replace all (4) shoe and

lining assemblies on both front wheels.

On Lincoln Continental brakes

make three thickness measurements

with a micrometer across the middle

section of the shoe and lining. Take

one reading at each side and one in

the center. If the assembly has worn

to a thickness of 0.231 inch (shoe and

lining together) or 0.066 inch (lining

material only) at any one of the three

measuring locations, replace all (4)

shoe and lining assemblies on both

front wheels.

3.
Check the caliper to spindle at-

taching bolts torque. Torque them to

specification, if required.

4.
To check rotor runout, first

eliminate the wheel bearing end play

by tightening the adjusting nut. After

tightening the nut, check to see that

the rotor can still be rotated.

5.
Clamp a dial indicator to the

caliper housing so that the stylus con-

tact the rotor at a point approximate-

ly 1 inch from the outer edge. Rotate

the rotor and take an indicator read-

ing. If the reading exceeds 0.003 inch

total lateral runout on the indicator,

replace or resurface the disc brake

rotor. The following requirement must

be met when resurfacing disc brake

rotors:
Rotunda Disc Brake Attachment

FRE-2249-2 is the only approved tool

to be used to refinish the disc brake

rotors.
The step-by-step resurfacing

procedure provided with the tool must

be adhered to.

The finished braking surface of the

rotor must be flat and parallel within

0.0007 inch; lateral runout must not

exceed 0.003 inch total indicator

reading, braking surface are to be 80/15

micro inches.

On all models except Lincoln Con-

tinental the minimum limiting dimen-

sion from the inboard bearing cup to

the inboard rotor face and the mini-

mum rotor thickness dimension, must

be observed when removing material

from the rotor braking surfaces. A

ball and gage bar (Rotunda Kit FRE

70160) is to be used when checking

minimum dimensions (Fig. 11).

FALCON-FAIRLANE

MUSTANG-COUGAR

MONTEGO

.046 MAX-**

.119
MAX.

FORD-MERCURY

METEOR - THUNDERBIRD
875
MIN

H1633-A

1.12
MIN.-^

??
— Disc Brake Rotor

Service Limits—All Models Except

Lincoln Continental

On Lincoln Continental models the

minimum limiting dimension (Fig. 12)

from the inboard bearing cup to the
inboard rotor face (dimension B)

and the outboard rotor surface and

the inboard bearing cup (dimension

A),
must be observed when remov-

ing material from the rotor braking

surfaces.

When the runout check is finished

be sure to adjust the bearings as out-

lined in Group 3, in order to prevent

bearing failure.

6. Check the rotor for scoring. Mi-

nor scores can be removed with a

fine emery cloth. If the rotor is ex-

cessively scored, refinish it as out-

lined in step 5 or replace the rotor,

if required.

7.
Visually check the caliper. If the

caliper housing is leaking it should be

replaced. If a seal is leaking the cali-

per must be disassembled and new

.seals installed. If a piston is seazed

in the bore a new caliper housing is

required.

On Lincoln Continental models the

two halves of the caliper assembly

should never be separated. Damage or

failure of one requires replacement of

both as a unit.

Check the brake hoses for signs of

cracking, leaks or abrasion. Replace

them if necessary.

DISC BRAKE SERVICE

PRECAUTIONS

1.
Grease or any other foreign ma-

terial must be kept off the caliper as-

sembly, surfaces of the rotor and ex-

ternal surfaces of the hub during serv-

ice operations. Handling of the rotor

and caliper assemblies should be done

in a way to avoid deformation of the

brake rotor and nicking or scratching

of brake linings.

2.
If a caliper piston is removed for

any reason, the piston seal must be re-

placed.

3.
During removal and installation

of a wheel assembly, exercise care not

to interfere with and damage the cali-procarmanuals.com

02-02-08
Brake System

02-02-08

Tool-HRE-8650

JUST SET TO DRUM

DIAMETER HERE . . .
FIND CORRECT BRAKE

SHOE DIAMETER HERE

H1416-A

FIG.
7
7—Adjusting Brake Shoes Using Tool HRE-8650

BOOT

BOOT

PISTON
. BLEEDER .

CYLINDER
SCREW RETURN SPRING PIST0N

H1385-B

FIG. 72—Brake Wheel Cylinder—Typical

DISASSEMBLY

1.
Remove the links and the rubber

boots from the ends of the brake cyl-

inder. Remove the pistons, cups, and

return spring from the cylinder bore

(Fig. 12).

2.
Remove the bleeder screw from

the cylinder.

INSPECTION

1.
Wash all parts in clean brake

fluid. Dry with compressed air.

2.
Replace scored pistons. Always

replace the rubber cups and dust

boots.
3.
Inspect the cylinder bore for

score marks or rust. If either condi-

tion is present the cylinder bore must

be honed. However, the cylinder

should not be honed more than 0.003

inch beyond its original diameter.

4.
Check the bleeder hole to be sure

that it is open.

ASSEMBLY

1.
Apply a light coating of heavy-

duty brake fluip! to all internal parts.

2.
Thread the bleeder screw into the

cylinder and tighten securely.

3.
Insert the return spring, cups,

and pistons into their respective posi-

tions in the cylinder bore (Fig. 12).
Place a boot over each end of the cyl-

inder. Bleed the brake system.

HYDRAULIC LINE REPAIR

Steel tubing is used throughout the

brake system with the exception of the

flexible hoses at the front wheels and

at the fear axle housing brake tube

connection (Figs. 17 thru 21).

Always bleed the applicable pri-

mary or secondary brake system after

primary or secondary brake system

hose or line replacement. Centralize

the pressure differential valve after

bleeding the system.

BRAKE TUBE

REPLACEMENT

If a section of the brake tubing be-

comes damaged, the entire section

should be replaced with tubing of the

same type, size, shape and length.

Copper tubing should not be used in a

hydraulic system. When bending

brake tubing to fit underbody or rear

axle contours, be careful not to kink

or crack the tube.

All brake tubing should be double

flared properly to provide good leak-

proof connections. Clean the brake

tubing by flushing with clean brake

fluid before installation.

When connecting a tube to a hose,

tube connector, or brake cylinder,

tighten the tube fitting nut to specified

torque with Milbar tool 1112-144 or

equivalent.

BRAKE HOSE

REPLACEMENT

A flexible brake hose should be re-

placed if it shows signs of softening,

cracking, or other damage.

When installing a new front brake

hose,
position the hose to avoid con-

tact with other chassis parts. Place a

new copper gasket over the hose fit-

ting and thread the hose assembly into

the front wheel cylinder. Engage the

opposite end of the hose to the brack-

et on the frame. Install the horsesho-

e-type retaining clip, and connect the

tube to the hose with the tube fitting

nut (Figs. 17 thru 21).

A rear brake hose should be in-

stalled so that it does not touch the

muffler outlet pipe or shock absorber.

Thread the hose into the rear brake

tube connector. Engage the front end

of the hose to the bracket on the

frame. Install the horseshoe-type re-

taining clip, and connect the tube to

the hose with the tube fitting nut.procarmanuals.com

02-02-18

Brake System

02-02-18

the brake hose connector
and
bracket

assembly.

3.
Remove
the two
bolts retaining

the brake hose bracket
and
caliper
as-

sembly
to the
spindle. Take care
to

avoid loosening
the
bridge bolts that

hold
the two
halves
of the
caliper
to-

gether.

4.
Lift
the
caliper assembly
off the

rotor
and
place
it on the
bench.

Installation

1.
If the
caliper assembly
is to be

replaced, transfer
the
steel tubing
and

the bleeder screw
to the new
caliper.

2.
Position
the
caliper assembly
on

the rotor,
and
mate
the
mounting bolt

holes
in the
caliper with those
in the

spindle.
It may be
necessary
to
push

the caliper pistons into
the
cylinder

bores
to
obtain clearance between
the

shoe
and
lining assembly
and the

rotor.
The
shoe
and
lining assemblies

should
be
seated properly
on the

bridges.

3.
Install
the
caliper
to
spindle
re-

taining bolts
and
torque them
to
spec-

ification. Check
to
insure that
the

rotor runs squarely
and
centrally
be-

tween
the two
halves
of the
caliper.

These should
be
approximately 0.090-

0.120 inch clearance between
the
cali-

per
and the
rotor outside diameter

(Fig.
6).

4.
Position
the
steel transfer tube

brake hose bracket
and
caliper assem-

bly
to the
spindle. Install
the
retaining

bolts then torque them
to
specifica-

tion.

5.
Connect
the
front wheel steel

transfer tube from
the
caliper
to the

front brake hose connector. Check
the

hose
for
proper installation
(Fig. 21).

6. Bleed
the
brake system
and cen-

tralize
the
differential valve
as out-

lined
in
Part
2-1.
Check
the
master

cylinder fluid level
and add the
speci-

fied fluid,
as
required. Pump
the

brake pedal several times
to
actuate

the piston seals
and to
position
the

shoe
and
lining assemblies.

7.
Install
the
wheel
and
tire assem-

bly
and the
wheel cover.

8. Road test
the
vehicle.

DISC BRAKE SHOE
AND

LINING

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Removal

1.
Remove
the
wheel
and
tire from
the
hub and
rotor assembly.

2.
Remove
the
caliper from
the ve-

hicle following
the
procedures outlined

under Disc Brake Caliper Assembly.

3.
To
facilitate removal
of the
cali-

per assemblies,
the
piston
may
have
to

be pushed into
its
bore. Apply
a

steady inward pressure against
the

inner shoe
and
lining assembly. Main-

tain
the
pressure
for at
least
a
minute.

4.
Slide
the two
outer shoe retain-

ing clips
off the
retaining pins
(Fig.

23).

5.
Remove
the two
retaining pins

from
the
outer shoe, then remove
the

shoe from
the
stationary caliper.

6. Slide
the
inner brake shoe
out-

ward until
it is
free
of the
hold-down

springs, then remove
the
brake shoe.

7.
Remove
the
caliper locating pins

and stabilizer attaching bolts, then
re-

move
and
discard
the
stabilizer
or sta-

bilizers.

8. Remove
the
locating
pin
insula-

tors from
the
anchor plate.

Installation

When installing
new
shoes
and lin-

ings
it
will
be
necessary
to
force
the

piston
to the
bottom
of its
bore.

Apply sufficient pressure
to
overcome

the grip
of the
piston seal
on the pis-

ton.

1.
Install
new
caliper locating
pin

insulators
in the
anchor plate.

2.
Position
the
caliper assembly
in

the anchor plate.

3.
Position
the new
stabilizer
or

stabilizers
and
install
the
caliper locat-

ing pins
to
engage approximately four

threads.

If
the
caliper locating pins
are
rust-

ed
or
corroded they should
be re-

placed.

Apply water
or
isopropyl alcohol
to

the caliper locating pins before instal-

lation.
Oil or
grease must
not be
used

on
the
locating pins.

4.
Position
the
outer brake shoe
on

the caliper
and
install
the two
retain-

ing pins
and
clips.

5.
Install
the
inner brake shoe
so

that
the
ears
of
shoe
are on top of the

anchor plate bosses
and
under
the

shoe hold-down springs.

6. Position
the
shoe
and
lining

assemblies
so
that
the
caliper assem-

bly
can be
placed over
the
rotor.
Ro-

tate
a
hammer handle between
the lin-

ings
to
reset
the
stabilizers.

7.
Install
the
caliper assembly over

the rotor
and on the
spindle. Install

the
two
caliper attaching bolts,
and

torque them
to
specifications.
The

upper bolt must
be
tightened first.
In-

stall
the
safety wire
and
twist
the
ends
at least five turns. Push
the
wire ends

against
the
spindle
to
avoid interfer-

ence with
the
brake hose
and the

steering stop.

8. With moderate pressure applied

to
the
brake pedal, torque
the
stabiliz-

er attaching screws
and
caliper locat-

ing pins
to
specification.

LINCOLN CONTINENTAL

Removal

1.
Remove
the
wheel
and
tire
as-

sembly from
the hub and
rotor assem-

bly.
Be
careful
to
avoid damage
or in-

terference with
the
caliper splash

shield, bleeder screw fitting
or
transfer

tube.

2.
Remove
the two
bolts that retain

the caliper splash shield,
and
remove

the shield
(Fig. 4).

3.
To
facilitate removal
and
instal-

lation
of the
shoe
and
lining assem-

blies,
the
pistons must
be
pushed into

their bores. Apply
a
steady inward

pressure against each shoe
and
lining

assembly toward
its
respective caliper

housing
on
each side
of the
rotor
(Fig.

6).
Maintain
the
pressure
for at
least

a minute.
If the
pistons will
not go ifi

easily, force them
in
with water pump

pliers.

4.
Grasp
the
metal flange
on the

outer
end of the
shoe with
two
pairs

of pliers
and
pull
the
shoe
out of the

caliper (Fig.
25).

Installation

1.
Position
a new
shoe
and
lining

assembly
on
each side
of the
rotor
so

that
the
lining faces
the
rotor.
Be
sure

AB

AB

USE SECOND

PAIR
OF

PLIERS HERE

H 1651
A

FIG. 25—Removing Disc Brake

Shoe
and
Lining Assembly—

Lincoln Continentalprocarmanuals.com

02-02-38
Brake System

02-02-38

2.
Disconnect the actuator solenoid

and warning switch harness connectors

from the control module.

3.
Remove the two wiring harness

grommets from the dash panel and

push the wiring harness and connec-

tors through the openings in the dash

panel.

4.
Working in the engine compart-

ment loosen the hose clamp and re-

move the air hose from the air filter.

5.
Remove the engine air cleaner-

Loosen the hose clamp and remove

the vacuum hose from the vacuum

manifold fitting.

6. Raise the vehicle on a hoist.

7.
Disconnect the exhaust pipes

from the exhaust manifold and sup-

port with wire to provide access to the

actuator assembly.

8. Remove the bolt retaining the

actuator ground wire to the rear outer

corner of the engine right bank.

9. Loosen the tube nuts and discon-

nect the brake system hydraulic tubes

from the hydraulic valve housing.

10.
Remove the three nuts retaining

the actuator assembly to the actuator

support bracket.

11.
Remove the three bolts that re-

tain the actuator mounting bracket to

the side rail and remove the mounting

bracket.

12.
Remove the actuator assembly

from the vehicle and place it on a

bench.

13.
Remove the air and vacuum

hoses from the actuator.

INSTALLATION

1.
Install the air and vacuum hoses

on the new actuator.

2.
Place the actuator assembly into

position under the vehicle, routing the

air and vacuum hoses up between the

engine and fender apron and inserting

the solenoid leads through the holes in

the firewall.

3.
Position the ground wire to the

rear of the engine block and install re-

taining bolt.

4.
Position the actuator mounting

bracket to the frame side rail and in-

stall the three retaining bolts.

5.
Position the actuator assembly

to the mounting bracket and install

the three retaining nuts.

6. Connect the hydraulic tubes to

the hydraulic valve assembly and

tighten the tube nuts to specifications.

7.
Connect the exhaust pipes to the

exhaust manifolds.

8. Lower the vehicle.

9. Pull the actuator solenoid and

brake warning switch wiring harness
through the two holes in the dash

panel from inside the car. Seat the

wiring harness grommets in the dash

panel.

10.
Connect the actuator solenoid

and brake warning switch wiring har-

ness connectors to the control mo-

dules.
'

11.
Position the control module in

the bracket under the glove box and

install the retaining screw.

12.
In the engine compartment con-

nect the air hose to the air filter and

position the hose clamp.

13.
Connect the vacuum hose to the

engine vacuum manifold fitting. In-

stall the engine air cleaner.

14.
Bleed the rear brake system and

centralize the pressure differential

valve.

15.
Raise the rear wheels. Apply

the brakes with the rear wheels turn-

ing to verify proper operation of the

anti-skid control system.

ANTI-SKID CONTROL MODULE

REMOVAL

Refer to Fig. 39.

1.
Remove the retaining strap hold-

ing the harnesses.

2.
Remove the screw that attaches

the forward end of the control module

retainer to the support assembly.

3.
Lower the forward end of the

control module and retainer from the

support assembly; move the module

and retainer forward slightly until the

flange clears the slot in the support

assembly.

4.
Disconnect the five wiring har-

ness plugs from the control module.

5.
Remove the control module from

the vehicle.

INSTALLATION

1.
Connect the five wiring harness

plugs to the control module. Only one

arrangement is possible.

2.
Position the control module in

the retainer, orienting the module per

the markings on it, and insert the re-

tainer flange into the slot at the rear

of the support assembly.

3.
Pivot the retainer and control

module upward and align the screw

hole in the forward end of the retainer

with the hole in the support bracket

assembly. Install the retaining screw.

4.
Test the vehicle on the hoist to

verify correct operation of the skid

control system.
5.-
Secure the wiring to the module

support extension with the retaining

strap.

ANTI-SKID CONTROL SENSOR

REMOVAL

Refer to Fig. 39.

1.
Raise the vehicle on a hoist.

2.
Remove the rear wheel and tire

assembly.

3.
Remove the three Tinnerman

nuts (3) and remove the brake drum.

4.
Disconnect the sensor lead from

the rear wiring harness.

5.
Unseat the sensor lead grommet

pushing it to the inside of the brake

assembly.

6. Remove the four nuts that retain

the sensor to the backing plate and

pull the axle shaft, sensor assembly

and wheel bearing assembly from the

axle housing.

7.
Press the wheel bearing retainer

and wheel bearing off the axle shaft

(Refer to Part 4-2).

8. Remove the sensor assembly and

press the rotor off the shaft with tool

T69P-2B384-A Detail 2 and TOOL

1225-DA.

INSTALLATION

1.
Press a new rotor onto the axle

shaft. Install a new sensor assembly

on the shaft with tool T69P-

2B384-ADetail 1 and TOOL 1225-

DA, and press the bearing and bear-

ing retainer onto the shaft (Refer to

Part 4-2).

2.
Insert the axle shaft assembly in

the rear axle housing onto the four

backing plate retaining bolts, feeding

the sensor lead through the hole in the

backing plate.

3.
Seat the sensor lead grommet in

the backing plate.

4.
Install the four nuts on the re-

taining bolts and tighten to specifica-

tions.

5.
Connect the sensor lead to the

rear wiring harness and install two re-

taining straps.

6. Install the rear brake drum and

retain with the Tinnerrhan drum re-

taining nuts.

7.
Install the rear wheel and tire as-

sembly and tighten the wheel nuts to

specifications.

8. Test the vehicle on the hoist to

verify proper operation of the skid

control system.procarmanuals.com

03-01-01

PART
3-1
PAGE

Suspension,
Steering, Wheels and

Tires,
General Service 03-01-01

PART
3-2

Suspension 03-02-01

PART
3-3

Automatic
Air
Leveling System ....03-03-01

PART
3-4

Automatic
Air
Leveling System

Lincoln Continental 03-04-01

PART
3-5

Steering Columns and Linkage ... 03-05-01

PART
3-6

Manual Steering 03-06-01

PART
3-7

Ford Design Non-Integral Power

Steering System
03-07-01
PART
3-8
PAGE

Ford Design Integral Power

Steering Gear 03-08-01

PART
3-9

Saginaw Design Integral Power

Steering Gear 03-09-01

PART
3-10

Ford-Thompson Power Steering

Pump 03-10-01

PART
3-11

Eaton Power Steering Pump 03-1
1-01

PART 3-12

Wheels and Tires 03-1 2-01

PART
3-13

Specifications
03-13-01

PART
3-1
Suspension,Steering, Wheels
and

Tires—General Service

COMPONENT INDEX

CASTER AND CAMBER ADJUSTMENTS

FRONT
END
INSPECTION

FRONT WHEEL ALIGNMENT CHECKS

LUBRICANT CHECKING PROCEDURE

POWER STEERING GEAR CLEANING

AND INSPECTION

POWER STEERING PRELIMINARY TESTS

POWER STEERING PUMP

Cleaning
and
Inspection

Flow
and
Pressure Tests

POWER STEERING SYSTEM FLUSHING

SHOCK ABSORBER CHECKS

STEERING WHEEL SPOKE POSITION

Adjustment

TOE-IN ADJUSTMENT

WHEEL BALANCING
MODEL APPLICATION
All
Models

01-08

01-03

01-07

01-09

01-02

01-11

01-07

01-07

01-07
Ford
01-05

01-09

01-02

01-09
Mercury
01-05

01-09

01-02

01-09
Meteor
01-05

01-09

01-02

01-09
Cougar
01-06

01-09

01-02

01-09
Fairlane
01-06

01-09

01-02

01-09
Falcon
01-06

01-09

01-02

01-09
Montego
01-06

01-09

01-02

Gl-09
Mustang
01-06

01-09

01-02

01-09
Lincoln-
Continental
01-06

01-09

01-03

N/A
Thunderbird
01-05

01-09

01-02

01-09
Continental-
Mark
III
01-05

01-10

01-03

N/A

A page number indicates that
the
item
is for the
vehicle listed
at the
head
of the
column.

N/A indicates that
the
item
is not
applicable
to the
vehicle listed.
procarmanuals.com

03-01-02
Suspension — Steering, Wheels And Tires — General Service

03-01-02

1 TESTING

POWER STEERING-

PRELIMINARY TESTS

The following preliminary checks

should always be made before per-

forming any operations.

AIR BLEEDING

Air in the power steering system

(shown by bubbles in the fluid) should

be bled. After making sure that the

reservoir is filled to specification (the

fluid must be at normal operating

temperature when the check is made),

turn the steering wheel through its full

travel three or four times. Do not hold

the wheels against their stops. Re-

check the fluid level.

CHECK FLUID LEVEL

Run the engine until the fluid is at

normal operating temperature. Then

turn the steering wheel all the way to

the left and right several times, and

shut off the engine.

Check the fluid level in the power

steering reservoir. The level must show

on the cross hatching between the bot-

tom of the dipstick and the full mark

(Fig. 1). If the level is low, add

enough automatic transmission fluid

C1AZ-19582-A to raise the level to

the F mark on the dipstick. Do not

overfill the reservoir.

CHECK PUMP BELT

If the pump belt is broken, glazed,

or worn, replace it with a new belt.

Use only the specified type of belt.

Refer to Part 3-13 for belt adjustment

procedure.

CHECK FOR FLUID

LEAKS

With the engine idling, turn the

steering wheel from stop to stop sever-

al times. Check all possible leakage

points. Tighten all loose fittings, and

replace any damaged lines or defective

seats.

CHECK TURNING EFFORT

With the front wheels properly al-

igned and tire pressures correct, check

the effort required to turn the steering

wheel.
G 1508- A

FIG.
1—Power
Steering Pump

Dipstick

1.
With the vehicle on dry concrete,

set the parking brakes.

2.
With the engine warmed up and

running at idle speed, turn the steering

wheel to the left and right several

times to warm the fluid.

3.
Attach a pull scale to the rim of

the steering wheel. Measure the pull

required to turn the wheel one com-

plete revolution in each direction. The

effort required to rotate the steering

wheel should not exceed specifications

given in Part 3-13.

POWER STEERING PUMP FLOW

AND PRESSURE TESTS—

EXCEPT LINCOLN CONTINENTAL

AND CONTINENTAL MARK III

The power steering flow and pres-

sure tests will show whether the pump,

steering gear or power assist control

RETURN LINE

POWER

STEERING PUMP

Sr
valve is causing the trouble. Steps out-

lined below should be followed to de-

termine the cause of the trouble.

PUMP FLOW TEST

1.
Depending on the equipment

present on the vehicle (air condition-

ing, power brakes, standard transmis-

sion),
one of the following options

may be used to connect the pump

pressure and return hoses to the test

tool (T56L-3361O-D and T68L-

33610-A):

a. Disconnect the pressure and re-

turn lines at the power steering pump

(Fig. 2). Obtain a power steering re-

turn hose from stock and connect the

end with the fitting to the output fit-

ting of the tool using the
5/8-18
SAE

female, 1/4 N.P. thread male fitting

provided. The end of the stock hose

(without the fitting) should be con-

nected to the return tube of the pump.

Connect the pressure hose from the

tool to the outlet fitting of the pump.

b.
Disconnect the pressure line at

the pump and connect the pressure

line from the test tool to the outlet fit-

ting of the pump. Disconnect the re-

turn line at the gear and connect it to

the output fitting of the tool, using the

5/8-18
SAE female, 1/4 N.P. thread

male fitting provided.

2.
After installing the lines by the

most advantageous method, proceed

as follows:

3.
Open the manual valves A and B

fully (Fig. 2).

CALIBRATED FLOW

DETERMINING ORIFICE

PRESSURE LINE

FIG. 2—Power Steering Pump Test Circuit Diagram
PRESSURE GAGE

G1611-Aprocarmanuals.com

03-01-03
Suspension — Steering, Wheels And Tires — General Service

03-01-03

4.
Connect a tachometer, start the

engine and operate it at idle speed

until the reservoir fluid temperature

reaches 165 to 175. This temperature

must be maintained throughout the

test. Valve B may be partially closed

to create a back pressure up to 350

psi to hasten the temperature rise. The

reservoir fluid must be at the proper

level.

5.
With the engine operating at rec-

ommended idle rpm and fluid temper-

ature noted in Step 4, close the manu-

al valve B. The minimum acceptable

pressure reading is 620 psi.

6. If the pressure gauge reading is

below the minimum specification, the

pump is at fault and should be re-

paired with necessary parts.

7.
If the reading is at or above the

minimum specification, the pump flow

is normal. Open manual valve B and

proceed to the Pump Fluid Pressure

Test.

PUMP FLUID

PRESSURE TEST

1.
Keep the lines and tools con-

nected as in the Pump Flow Test.

2.
With manual valves A and B

opened fully, operate the engine at

recommended idle speed (Fig. 2).

Close manual valve A, then manual

valve B. Do not keep both valves

closed for more than 5 seconds as this

would abnormally increase the fluid

temperature and cause undue pump

and/or gear wear.

3.
With the valves fully closed, the

pressure gauge should read 1000 psi

minimum for Ford, Mercury, Meteor

or Thunderbird and 750 psi minimum

for Cougar, Fairlane, Falcon, Monte-

go or Mustang.

4.
If the pressure gauge reading is

below the minimum specification, the

pump is at fault and should be re-

paired with necessary parts.

5.
If the pressure gauge reading is

at or above the minimum specifica-

tions,
the pump is normal and the

power steering gear or power assist

control valve is at fault.

FLUID PRESSURE TEST-

LINCOLN CONTINENTAL AND

CONTINENTAL MARK III

The pressure testing gauge set, tool

T56L-33610-D, requires modification

to make it adaptable for installation

in the power steering hydraulic sys-

tem. The parts required and the modi-

fication procedure are as follows:
OWER STEERING

PRESSURE LINE

INVERTED FLARE

CONNECTOR

%* TUBE x VA" PIPE

FLARED FEMALE COUPW

%' TUBE x VA" PIPE

G1544.A

FIG. 3—Modified Pressure Gauge

Assembly

a. Power Steering Pressure Line

(refer to the appropriate Parts Catal-

og).

b.
Inverted Flare Connector (3/8

inch OD Tube x 1/4 inch Pipe

Thread).

c. Inverted Flare Connector (5/16

inch OD Tube x 1/4 inch Pipe

Thread).

d. Flared Tube Female Coupling

(3/8 inch OD Tube x 1/4 inch Pipe

Thread).

The connectors and the coupling are

standard-type fittings and can be pur-

chased locally.

e. To modify tool T56L-33610-D,

remove the hose from the hand shut-

off valve block. Install the 3/8 inch x

1/4 inch inverted flare connector in

the valve block, and assemble the

pressure line to the connector (Fig. 3).

Assemble the 3/8 x 1/4 inch coupling

and the 5/16-inch connector to the

free end of the hose leading to the.

pressure gauge.

1.
To check the pump pressure, dis-

connect the front and rear sections of

the pressure line over the number 6

cylinder. Connect the modified pres-

sure-testing gauge assembly, tool

T56L-3361O-D, between the two sec-

tions.

2.
Make sure the hand-valve at the

gauge is fully opened. Start the engine

and cycle the steering gear from stop

to stop to warm up the fluid. Check

the fluid level in the reservoir and add

fluid, if necessary.

3.
Turn the steering wheel to the

full right and full left turn positions

and observe the gauge readings.

Hold the wheels in this position

only long enough to obtain an accu-

rate reading. Do not exceed 5 seconds.

The gauge should read between

1120 and 1250 psi. If the pressure is
less than 1120 psi, close the valve at

the gauge and note the pump pressure.

If it is low with the valve closed, it in-

dicates that the pump is not operating

properly. If the pressure goes up with

the valve closed, it indicates that the

low pressure in the system must be

due to internal leakage in the power

unit, providing all connections are

tight.

4.
Remove the pressure testing

gauge set, and connect the pressure

line at the steering gear. Fill and bleed

the system.

FRONT WHEEL ALIGNMENT

CHECKS

Do not attempt to check and adjust

front wheel alignment without first

making a preliminary inspection of

the front-end parts. Refer to Section

3.

Check all the factors of front wheel

alignment except the turning angle

before making any adjustments. The

turning angle should be checked only

after caster, camber, and toe-in have

been adjusted to specifications.

The front wheel alignment specifica-

tions given in Part 3-13, are correct

only when the vehicle is at curb load.

Before checking or adjusting the

alignment factors, the suspension

alignment spacers must be installed to

obtain the curb Height.

EQUIPMENT INSTALLATION

Equipment used for front wheel

alignment inspection must be accu-

rate.
Whenever possible, front wheel

alignment checks should be performed

on stationary wheel aligning equip-

Too/
- T65P3000-A or S

FIG. 4—Typical Front Alignment

Spacer Installation—Cougar,

Fairlane, Falcon,
Montego,
Mustangprocarmanuals.com

03-01-08
Suspension
—
Steering,
Wheels
And
Tires
—
General Service

03-01-08

3.
Remove the lower (upper on

Mustang and Cougar) cover- to-

housing attaching bolt.

4.
With a clean punch or like in-

strument, clean out or push inward

the loose lubricant in the filler plug

hole and cover to housing attaching

bolt hole.
5.
Slowly turn the steering wheel to

the left stop, lubricant should rise

within the lower cover bolt hole; then

slowly turn the steering wheel to the

right stop, lubricant should rise within

the filler plug hole. If lubricant does

not rise in both the cover bolt hole
and the filler plug hole, add lubricant

until it comes out both holes during

this check.

6. Install the lower (upper on

Mustang and Cougar) cover- to-

housing attaching bolt and the filler

plug.

CLEANING
AND
INSPECTION

FRONT
END
GENERAL

INSPECTION

Do not check and adjust front

wheel alignment without first making

the following inspection for front-end

damage, or wear.

1.
Check for specified air pressures

in all four tires.

2.
Raise the front of the vehicle off

the floor. Shake each front wheel

grasping the upper and lower surfaces

of the tire. Check the front suspension

ball joints and mountings for loose-

ness,
wear, and damage. Check the

brake backing plate mountings. Tor-

que all loose nuts and bolts to specifi-

cation. Replace all worn parts as out-

lined in Part 3-2.

3.
Check the steering gear mount-

ings and all steering linkage connec-

tions for looseness. Torque all mount-

ings to specifications. If any of the

linkage is worn or bent, replace the

parts as outlined in Part 3-5.

4.
Check the front wheel bearings.

If any in-and-out free play is noticed,

adjust the bearings to specifications.

Replace worn or damaged bearings as

outlined in Part 3-12.

5.
Spin each front wheel with a

wheel spinner, and check and balance

each wheel as required.

6. Check the action of the shock

absorbers. If the shock absorbers are

not in good condition, the vehicle may

not settle in a normal, level position,

and front wheel alignment may be af-

fected.

WHEEL INSPECTION

Wheel hub nuts should be inspected

and tightened to specification at pre-

delivery. Loose wheel hub nuts may

cause shimmy and vibration. Elongat-

ed stud holes in the wheels may also

result from loose hub nuts.

Keep the wheels and hubs clean.

Stones wedged between the wheel and

drum and lumps of mud or grease can

unbalance a wheel and tire.
Check for damage that would affect

the runout of the wheels. Wobble or

shimmy caused by a damaged wheel

will eventually damage the wheel bear-

ings.
Inspect the wheel rims for dents

that could permit air to leak from the

tires.

UPPER BALL JOINT

INSPECTION

Ford,
Mercury,
Meteor,

Thunderbird,

Lincoln Continental
and

Continental Mark
III

1.
Raise the vehicle and place floor

jacks beneath the lower arms.

2.
Ask an assistant to grasp the

lower edge of the tire and move the

wheel in and out.

3.
As the wheel is being moved in

and out, observe the upper end of the

spindle and the upper arm.

4.
Any movement between the

upper end of the spindle and the upper

arm indicates ball joint wear and loss

of preload. If any such movement is

observed, replace the upper ball joint.

During
the
foregoing
check,
the

lower ball joint will
be
unloaded
and

may
move.
Disregard
all
such
move-

ment
of the
lower ball
joint.
Also,
do

not mistake loose wheel bearings
for a

worn ball
joint.

Cougar,
Fairlane,
Falcon,

Montego
and
Mustang

1.
Raise the vehicle on a frame

contact hoist or by floor jacks placed

beneath the underbody until the wheel

falls to the full down position as

shown in Fig. 18. This will unload the

upper ball joint.

2.
Adjust the wheel bearings as de-

scribed in Part 3-12.

3.
Attach a dial indicator to the

upper arm and position the indicator
so that the plunger rests against the

inner side of the wheel rim adjacent to

the upper arm ball joint.

4.
Grasp the tire at the top and

bottom, and slowly move the tire in

and out (Fig. 18). Note the reading

(radial play) on the dial indicator. If

MAXIMUM TOLERANCE

F
1500-A

FIG.
T8—Measuring Upper Ball

Joint Radial Play

MAXIMUM TOLERANCE

F14
35-A

FIG.
79—Measuring Lower Ball

Joint Radial Playprocarmanuals.com