tire pressure FORD MUSTANG 1969 Volume One Chassis

03-02-18
Suspension

03-02-18

5.
Remove the cotter pin from the

upper ball joint stud nut.

6. Loosen the upper ball joint stud

nut one or two turns. Do not remove

the nut from the stud at this time.

7.
Install tool T57P-3006-A be-

tween the upper and lower ball joint

studs with the adapter screw on top

(Fig. 13). The tool should be seated

firmly against the ends of both studs

and not against the nuts or lower stud

cotter pin.

8. With a wrench, turn the adapter

screw until the tool places the stua

under tension. Tap the spindle near

the upper stud with a hammer to loos-

en the stud in the spindle. Do not

loosen the stud from the spindle with

tool pressure only.

9. Remove the tool from between

the ball joint studs and place a floor

jack under the lower arm.

10.
Raise the floor jack to relieve

the pressure from the upper ball joint

stud nut and remove the nut.

11.
Remove the upper arm inner

shaft attaching bolts. Remove the

upper arm and inner shaft as an as-

sembly (Fig. 1).

12.
Remove the bumpei from the

upper arm.

Installation

1.
Position the bumper to the upper

arm and install the nut and washer.

Torque the nut to specifications.

2.
Position the upper arm inner

shaft to the frame side rail and install

the 2 attaching bolts and washers

snug.

3.
Connect the upper ball joint stud

to the spindle and install the attaching

nut. Torque the nut to specification

and continue to tighten the nut until

the cotter pin hole in the stud is in

line with the nut slots. Then, install

the cotter pin.

4.
If equipped with drum type bra-

kes—Adjust the brakes as outlined in

Part 2-2. Install the wheel, tire, and

drum to the spindle and adjust the

wheel bearings as outlined in Part

3-12.

5.
If equipped with disc brak-

es—Install the wheel and tire on the

hub and adjust the wheel bearings as

outlined in Part 3-12.

6. Install the hub cap or wheel

cover.

7.
Remove the safety stands and

lower the front of the vehicle.

8. Check caster, camber, and toe-in

and adjust as required (Section 2, Part

3-D.
COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Removal

1.
Raise the front of the vehicle,

position safety stands under the

frame, and lower the vehicle slightly.

2.
Remove the wheel and tire.

3.
Remove the shock absorber

lower attaching nuts and washers.

4.
Remove the shock absorber

upper mounting bracket attaching

nuts,
and remove the shock absorber

and bracket as an assembly (Fig. 26).

On all 8-cylinder vehicles, remove

the air cleaner to obtain access for

tool installation.

5.
Install the spring compressor

tool and compress the spring (Figs.

19,
20 and 21).

6. Position a safety stand under the

lower arm.

7.
Remove the cotter pin from the

nut on the upper ball joint stud, and

loosen the nut one or two turns. Do

not remove the nut from the stud at

this time.

8. Position the ball joint remover

tool between the upper and lower ball

joint studs as shown in Fig. 10. The

tool should seat firmly against the

ends of both studs and not against the

stud nuts.

9. Turn the tool with a wrench until

the tool places the studs under consid-

erable tension; then, hit the spindle

smartly near the upper stud with a

hammer to break the stud loose in the

spindle. Do not loosen the stud in the

spindle with tool pressure only. If

both arms are being removed, loosen

the lower stud in the same manner as

the upper stud.

10.
Remove the nut from the upper

stud and lift the stud out of the

spindle.

11.
Remove the upper arm inner

shaft attaching nuts from the engine

compartment, and remove the upper

arm.

12.
Wipe off all loose dirt from the

upper arm parts. Do not wash the ball

joint with a solvent.

Installation

1.
Position the upper arm on the

underbody mounting bracket, and in-

stall the nuts and lock washers on the

two inner shaft attaching bolts. The

specified keystone-type lock washers

must be used. Torque the nuts to

soecification.
2.
Position the upper ball joint stud

in the top of the wheel spindle, and in-

stall the stud nut. Torque the nut to

specification, and continue to tighten

it until the cotter pin hole and slots

line up. Install a new cotter pin.

3.
Release the coil spring, remove

the tool, and install the front shock

absorber and the wheel and tire.

LINCOLN CONTINENTAL

Removal

1.
Place a jack under the outer end

of the suspension lower arm and raise

the arm. Refer to Fig. 22.

2.
Remove the wheel and tire.

3.
Remove the cotter pin from the

upper ball joint stud. Loosen the nut

one or two turns.

4.
Place a box wrench over the

lower end of the ball joint remover

tool, and position the tool as in Fig.

13.
The tool should seat firmly against

the ends of both studs, and not

against the upper stud nut.

5.
Turn the wrench until both studs

are under tension, and then, tap the

spindle with a hammer near the upper

stud to loosen it from the spindle. Do

not loosen the stud with tool pressure

alone. Remove the nut.

UPPER MOUNTING BRACKET

LOWER RETAINING BOLTS F 1490-A

FIG. 26—Removing or Installing

Front Shock Absorber—Typicalprocarmanuals.com

03-02-19

Suspension

03-02-19

6. Raise the upper arm to free the

ball joint stud from the spindle. Wire

the upper end of the spindle to the un-

derbody to prevent damage to the

brake hose.

7.
Mark the position of the upper

arm shaft on the underbody member

to facilitate making caster and camber

adjustments after installation of the

upper arm.

8. Remove the suspension upper

arm-to-underbody attaching bolts,

lock washers, and attaching nuts.

Then, remove the upper arm.

Installation

1.
Position the upper arm shaft on

the underbody member. Line up the

shaft with the marks made before re-

moval of the arm.

2.
Install the attaching bolts and

lock washers. FABRICATE A

TOOL, AS SHOWN IN Fig. 27, to

hold the nut in place while starting the

attaching bolt into the nut. Remove

the tool; then, tighten the attaching

bolts to specification.

3.
Guide the ball joint stud into the

spindle. Install the attaching nut and

torque it to specification. Continue

tightening the nut to line up the cotter

pin hole. Install a new cotter pin.

4.
Install the wheel and tire, and

torque the wheel lug nuts to specifica-

tion.

5.
With the front end weight of the

car on the wheels, torque the bolts at

the ends of the upper arm shaft to

specification if the bushings were re-

placed.

6. Check the front wheel alignment.

FRONT WHEEL SPINDLE

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK III

Removal

1.
Raise the vehicle until the front

wheel clears the floor, and place a

support under the frame.

2.
Remove the hub cap or wheel

cover.

3.
If equipped with drum type

brakes—remove the wheel and tire

and brake drum as an assembly (Part

3-12). Remove the brake backing

plate attaching bolts and remove the

backing plate from the spindle. Wire

the backing plate to the underbody to

prevent damage to the brake hose.
1/16" GAUGE
-*.

STEEL (REFERENCE)

—3/16'
3/8'

1/2" DIAMETER PLUG WELD

F 1501-A

FIG. 27 -Upper Arm Shaft Installing Tool

4.
If equipped with disc brakes—re-

move the wheel and tire from the hub.

Remove 2 bolts and washers retaining

the caliper and brake hose to the

spindle. Remove the caliper from the

rotor and wire it to the underbody to

prevent damage to the brake hose.

Then, remove the hub and rotor from

the spindle (Part 3-12). Remove 3

bolts attaching the splash shield to the

spindle and remove the splash shield.

5.
Remove the steering connecting

rod from the spindle arm with tool

OTC462.

6. Remove the cotter pins from

both ball joint stud nuts, and loosen

the nuts one or two turns. Do not re-

move the nuts from the studs at this

time.

7.
Install the ball joint remover tool

between the upper and lower ball joint

studs (Fig. 7). The tool sho.uld seat

firmly against the ends of both studs

and not against the stud nuts.

8. Turn the tool nut with a wrench

until the tool places the studs under

tension, and, with a hammer, tap the

spindle near the stud to loosen them

in the spindle. Do not loosen the studs

in the spindle with tool pressure only.

9. Position a floor jack under the

lower control arm.

10.
Remove the ball joint stud nuts

and lower the lower arm enough to re-

move the spring and the spindle.
Installation

1.
Position the spindle to the lower

ball joint stud and install the attaching

nut. Torque the nut to specification.

Continue to tighten the nut until the

cotter pin hole is in line with the slots

in the nut. Then, install the cotter pin.

2.
Position the spring and raise the

lower arm and guide and upper ball

joint stud into the spindle hole and in-

stall the attaching nut. Torque the nut

to specification and install the cotter

pin as outlined in the preceeding step.

3.
Remove the floor jack from

under the lower arm.

4.
Attach the steering connecting

rod to the spindle and install the nut.

Torque the nut to specification. Con-

tinue to tighten the nut until the cotter

pin hole is in line with the slots in the

nut. Then, install the cotter pin.

5.
If equipped with drum type

brakes—Position the brake backing

plate to the spindle and install the at-

taching bolts. Torque the bolts to spe-

cification. Adjust the brakes as out-

lined in Part 2-2. Install the wheel,

tire,
and drum to the spindle and ad-

just the wheel bearings as outlined in

Part 3-12).

6. If equipped with disc brak-

es—Install the splash shield on the

spindle and torque the attaching bolts

to specification (Part 3-13). Install theprocarmanuals.com

03-02-20
Suspension

03-02-20

hub and rotor on the spindle. Position

the caliper over the rotor and install

the attaching bolts. Torque the bolts

to specification (Part 3-13). Install the

wheel and tire on the hub and adjust

the wheel bearings as outlined in Part

3-12 .

7.
Install the hub cap or wheel

cover. Then, remove the support stand

and lower the vehicle.

8. Check caster, camber, and toe-in

(Part 3-1) and adjust as necessary.

COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Drum Brakes

Removal

1.
Position a support between the

upper arm and frame as shown in

Figs.
8 and 9; then, raise the vehicle

and position safety stands.

2.
Remove the hub cap or wheel

cover.

3.
Remove the grease cap from the

hub;
then, remove the adjusting nut,

washer, and outer bearing cone and

roller assembly.

4.
Pull the wheel, hub, and drum

assembly off the wheel spindle.

5.
Remove the brake backing plate

from the spindle. Support the plate to

prevent damage to the brake hose.

6. Disconnect the spindle connect-

ing rod end from the spindle arm

using Tool 3290-C.

7.
Remove the cotter pins from

both ball joint stud nuts, and loosen

the nuts one or two turns. Do not re-

move the nuts from the studs at this

time.

8. Position the ball joint remover

tool between the upper and lower ball

joint studs (Fig. 10). The tool should

seat firmly against the ends of both

studs and not against the stud nuts.

9. Turn the tool with a wrench until

the tool places the studs under consid-

erable tension, and, with a hammer,

hit the spindle smartly near the studs

to break them loose in the spindle. Do

not loosen the studs in the spindle

with tool pressure alone.

10.
Remove the stud nuts and re-

move the spindle from both studs.

Installation

1.
Position the spindle on the lower

ball joint stud and install the stud nut

(Fig. 25).
2.
Raise the lower suspension arm

and guide the upper ball joint stud

into the spindle. Install the stud nut.

3.
Torque the upper stud nut and

then the lower stud nut to specifica-

tion. Continue to tighten both nuts

until the cotter pin holes and slots line

up.
Install new cotter pins.

4.
Connect the spindle connecting

rod end to the spindle arm.

5.
Install the brake backing plate

on the spindle, and torque the bolts to

specification.

6. Install the wntel and drum and

adjust the wheel bearing (Part 3-12).

7.
Remove the safety stands, and

lower the vehicle.

8. Remove the support from be-

tween the upper arm and frame.

9. Check and, if necessary, adjust

caster, camber, and toe-in.

Disc Brakes

Removal

1.
Remove the hub cap or wheel

cover, and remove the wheel and tire

from the hub.

2.
Remove two bolts attaching the

caliper to the spindle. Remove the cal-

iper from the rotor and wire it to the

underbody to prevent damage to the

brake hose.

3.
Remove the grease cap from the

hub,
then, remove the adjusting nut,

washer, and outer bearing cone and

roller assembly.

4.
Pull the hub and rotor assembly

off the wheel spindle.

5.
Remove the three caliper shield

attaching bolts and remove the shield.

6. Disconnect the spindle connect-

ing rod end from the spindle arm

using Tool-3290-C.

7.
Remove the cotter pins from

both ball joint stud nuts, and loosen

the nuts one or two turns. Do not re-

move the nuts from the studs at this

time.

8. Position the ball joint remover

tool between the upper and lower ball

joint studs (Fig. 10). The tool should

seat firmly against the ends of both

studs and not against the stud nuts.

9. Turn the tool with a wrench until

the tool places the studs under consid-

erable tension, and, with a hammer,

hit the spindle smartly near the studs

to break them loose in the spindle. Do

not loosen the studs in the spindle

with tool pressure alone.

10.
Position a floor jack under the

lower suspension arm.
11.
Remove the upper and lower

ball joint stud nuts; lower the jack

and remove the spindle.

Installation

1.
Position the spindle on the lower

ball joint stud and install the stud nut

(Fig. 25). Torque the nut to specifica-

tion and install the cotter pin.

2.
Raise the lower suspension arm,

and guide the upper ball joint stud

into the spindle. Install the stud nut.

3.
Torque the nut to specifications

and install the cotter pin. Then, re-

move the floor jack.

4.
Connect the spindle connecting

rod end to the spindle arm and install

the attaching nut. Torque the nut to

specification and install the cotter pin.

5.
Position the caliper splash shield

to the spindle and install the attaching

bolts and nuts. Torque the nuts and

bolts to specification.

6. Install the hub and rotor on the

spindle.

7.
Position the caliper to the rotor

and spindle and install the attaching

bolts.
Torque the bolts to specification

and install the safety wire.

8. Install the wheel and tire on the

hub and adjust the wheel bearing

(Part 3-12).

9. Install the hub cap or wheel

cover.

10.
Before driving the vehicle,

pump the brake pedal several times to

obtain normal brake lining-to-rotor

clearance and restore normal brake

pedal travel.

LINCOLN CONTINENTAL

Removal

1.
Raise the vehicle. Place a sup-

port under each side rail to the rear of

the lower arm in the lifting pad area.

2.
Remove the wheel and tire from

the hub.

3.
Remove 2 bolts and washers that

attach the caliper to the spindle. Re-

move the caliper from the rotor and

wire it to the underbody to prevent

damage to the brake hose.

4.
Remove the hub and rotor from

the spindle.

5.
Remove the splash shield and

gasket from the spindle.

6. Disconnect the spindle arm con-

necting rod from the spindle arm with

Tool 3290-C. See Fig. 23.

7.
Remove the cotter pins from

both ball joint stud nuts. Loosen the

nuts one to two turns.procarmanuals.com

03-02-21
Suspension

03-02-21

8. Place a box wrench over the

lower end of the ball joint remover

tool, and position the tool as in Fig.

13.
The tool should seat firmly against

the ends of both studs, and not

against the stud nuts.

9. Turn the wrench until both studs

are under tension, and then, tap the

spindle with a hammer near the studs

to loosen them from the spindle. Do

not loosen
the
studs with tool pressure

alone.

10.
Place a jack under the outer

end of the lower arm, and raise the

arm several inches. Remove both ball

stud nuts, and remove t^e spindle.

Installation

1.
Position the new spindle onto the

upper and lower ball joint studs, in-

stall the stud nuts and tighten the nuts

to specifications. Continue to tighten

both nuts until the cotter pin holes

line up with the slots, then install new

cotter pines.

2.
Connect the spindle connecting

rod to the spindle arm. Install the re-

taining nut and tighten the nut to

specification. Continue to tighten the

nut until the cotter pin hole lines up

with the slot, then install a new cotter

pin.

3.
Install the gasket and splash

shield on the spindle. Tighten the at-

taching bolts to specifications.

4.
Install the hub and rotor on the

spindle.

5.
Install the caliper to the spindle

and tighten the attaching bolts to spe-

cifications. Check for the correct flex-

ible hose routing (Part 2-2).

6. Install the wheel and tire and ad-

just the wheel bearings (Part 3-12).

7.
Lubricate the steering stop on

the lower arm and the mating flat on

the spindle with the specified lubri-

cant.

8. Remove the safety stands, lower

the car and check camber, caster and

toe-in.

FRONT SHOCK ABSORBER

REPLACEMENT

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK III

1.
Remove the nut, washer, and

bushing from the shock absorber

upper end.

2.
Raise the vehicle on a hoist and

install safety stands.
3.
Remove 2 bolts attaching the

shock absorber to the lower arm and

remove the shock absorber.

4.
Place a washer and bushing on

the shock absorber top stud and posi-

tion the shock absorber inside the

front spring. Install the 2 lower at-

taching bolts and torque them to spe-

cifications.

5.
Remove the safety stands and

lower the vehicle.

6. Place a bushing and washer on

the shock absorber top stud and in-

stall the attaching nut. Torque it to

specification.

COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Removal

1. Raise the hood and remove 3

shock absorber upper mounting

bracket-to-spring tower attaching

nuts.

2.
Raise the front of the vehicle and

place safety stands under the lower

arms.

3.
Remove 2 shock absorber lower

attaching nuts and washers.

4.
Lift the shock absorber and

upper bracket from the spring tower

(Fig. 26) and remove the bracket from

the shock absorber.

Installation

1. Install the upper mounting

bracket on the shock absorber and

torque to specification.

2.
Position the shock absorber and

upper mounting bracket in the spring

tower, making sure the shock absor-

ber lower studs are in the pivot plate

holes.

3.
Install the 2 washers and attach-

ing nuts on the shock absorber lower

studs and torque to specification.

4.
Install the 3 shock absorber

upper mounting bracket-to-spring

tower attaching nuts and torque to

specification. Then, remove the safety

stands and lower the vehicle.

LINCOLN CONTINENTAL

Removal

1.
Remove the stud nut at the

upper eye of the shock absorber. Re-

move the upper eye stud bracket to

crossmember attaching bolt and re-

move the stud bracket. Refer to Fig.

22.
2.
Remove the bolts which attach

the shock absorber to the suspension

lower arm. Lower, and remove the

shock absorber.

3.
Examine the shock absorber unit

and rubber bushings. Replace parts

that are defective, deteriorated, or

worn.

Installation

1. Fully extend the shock absorber

and position it inside the coil spring.

Connect the lower end of the shock

absorber to the suspension lower arm.

Torque the attaching nuts to specifica-

tion.

2.
Insert the upper bracket stud

through the bushing in the shock ab-

sorber upper eye. Install the stud

bracket to crossmember attaching

bolt. Do not tighten the bolt: at this

time.

3.
Install the upper eye bracket

stud nut. Torque the nut to specifica-

tion.

4.
Torque the stud bracket- to-

crossmember attaching bolt to specifi-

cation.
The
shock absorber upper
eye

stud
nut
must
be
tightened
to com-

press
the
rubber bushing before
the

stud bracket
is
bolted
to the

crossmember;
otherwise,
the
upper
at-

tachment could
be
loose
and
noisy.

REAR SHOCK ABSORBER

REPLACEMENT

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK 1(11

1.
Raise the vehicle on a hoist.

2.
Remove the shock absorber at-

taching nut, washer and insulator

from the upper stud at the upper side

of the spring upper seat. Compress the

shock absorber to clear the hole in the

spring seat, and remove the inner in-

sulator and washer from the upper at-

taching stud.

3.
Remove the self-locking attach-

ing nut, and disconnect the shock ab-

sorber lower stud from the mounting

bracket on the rear axle housing (Fig.

4).

4.
Expel all air by performing step

3 On Vehicle Tests in Part 3-1.

5.
Place the inner washer and insu-

lator on the upper attaching stud, and

position the shock absorber so that

the upper attaching stud enters the

hole in the spring upper seat. While

holding the shock absorber in this po-

sition, install the outer insulator andprocarmanuals.com

03-09-01
Saginaw Design Integral Power Steering Gear

03-09-01

PART 3-9 Saginaw Design

Integral Power Steering Gear

COMPONENT INDEX

STEERING GEAR

Cleaning and Inspection (See Page 03-01)

Description

Disassembly and Assembly

Mesh Load Adjustment

Removal and Installation

Overhaul
MODEL APPLICATION
All
Models
Ford

09-01

09-03

09-01

09-02

09-04
Mercury
N/A

N/A

N/A

N/A

N/A

N/A
Meteor
N/A

N/A

N/A

N/A

N/A

N/A
Cougar
N/A

N/A

N/A

N/A

N/A

N/A
Fairlane
N/A

N/A

N/A

N/A

N/A

N/A
Falcon
N/A

N/A

N/A

N/A

N/A

N/A
Montego
N/A

N/A

N/A

N/A

N/A

N/A
Mustang
N/A

N/A

N/A

N/A

N/A

N/A
Lincoln-
Continental
N/A

N/A

N/A

N/A

N/A

N/A
Thunderbird
N/A

N/A

N/A

N/A

N/\

N/A
Continental-
Mark III
N/A

N/A

N/A

N/A

N/A

N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

DESCRIPTION

The Rotary Valve Safety power

steering gear operates entirely on dis-

placing fluid to provide hydraulic fluid

pressure assists only when turning. As

the entire gear assembly is always full

of fluid, all internal components of the

gear are immersed in fluid making

periodic lubrication unnecessary. In

addition, this fluid acts as a cushion
to absorb road shocks that may be

transmitted to the driver. All fluid

passages are internal except the pres-

sure and return hoses between the

gear and pump.

The rotary valve provides a smooth

transmission through the driving range

of steering wheel effort. A torsion bar

transmits the road feel to the driver.
Response of the steering gear to effort

applied to the steering wheel has been

greatly increased.

The rack-piston nut is one piece and

is geared to the sector shaft. Lash be-

tween the sector shaft and rack-piston

nut is maintained by an adjusting

screw which is retained in the end o\'

the shaft uear (Eiiz.l).

IN-VEHICLE ADJUSTMENTS AND REPAIRS

During the breaking in period of

the vehicle, it is probable that some

of the factory adjustments will change.

These changes in adjustment do not

necessarily affect the satisfactory op-

eration of the steering gear assembly

and ordinarily do not require re-ad-

justment unless there is excessive lash

or other malfunctioning. The only ad-

justment that should be performed in

the vehicle is the total over center

position load (mesh load) to eliminate

excessive lash between the sector shaft

and rack teeth.

MESH LOAD ADJUSTMENT

1.
Disconnect the Pitman arm from
the sector shaft and remove the steer-

ing wheel hub.

2.
Disconnect the fluid return line

at the reservoir; at the same time cap

the reservoir return line pipe.

3.
Place the end of the return line

in a clean container and cycle the

steering wheel in both directions as

required, to discharge the fluid from

the gear.

4.
Turn the gear 1/2 turn off cen-

ter (either direction). Using a 24 in-

lb torque wrench on the steering wheel

nut, determine the torque required to

rotate the shaft slowly through a 20

degree arc.

5.
Turn the sear back to center and
repeating the method of reading tor-

que as in Step 4, above, loosen the

adjuster lock nut, turn the screw in-

ward with a 7/32-inch Allen wrench

until the reading is equal to 6 in-lbs

in excess of Step 4 above, and retigh-

ten the lock nut while holding the

screw in place.

6. Recheck the readings and re-

place the Pitman arm and the steering

wheel hub.

7.
Connect the fluid return line to

the reservoir and fill the reservoir

with C1AZ-I9582-A Fluid to the

proper level.
procarmanuals.com

03-12-02
Wheels
And
Tires

03-12-02

LIFE GUARD TIRE

The Goodyear Power Cushion Tire

(available
on
Thunderbird, Lincoln

and Continental Mark
III
models)
fit-

ted with
the
Life Guard Safety Spare
provides
a
tire within
a
tire with
two

separate
air
chambers
(Fig.
3). If the

outer tire casing should
be
punctured

or otherwise damaged causing
it to go

flat,
the
Life Guard Safety Spare will

carry
the
load
of the
vehicle
and
will
allow driving
at
speeds
up to 40 mph

with good control
up to a
distance
of

40 miles.
A
Safety-Signal built into

the Life Guard tread produces
a
lope

or vibration indicating
the
outer tire

has lost pressure.

HUB AND ROTOR

ASSEMBLY
INNER

BEARING

CUP
GREASE

RETAINER

ADJUSTING

NUT

OUTER

BEARING

CONE
AND

ROLLER

INNER BEARING

CONE
AND

ROLLER

WHEEL

ASSEMBLY

F1416-A

F- 1380 •
A

FIG. 2—Front
Hub and
Rotor Bearing
and
Grease

Retainer Disc Brakes—Typical
FIG. 3—Life Guard Safety

Tire—Sectional View

IN-VEHICLE ADJUSTMENTS AND REPAIRS

HOISTING INSTRUCTIONS

Damage
to
steering linkage compo-

nents
and
front suspension struts
may

occur
if
care
is
not
exercised when
po-

sitioning
the
hoist adapters
of 2
post

hoists prior
to
lifting
the
vehicle.

If
a 2
post hoist
is
used
to
lift
the

vehicle, place
the
adapters under
the

lower arms
or
the No. 1
crossmember.

Do
not
allow
the
adapters
to
contact

steering linkage.
If the
adapters
are

placed under
the
crossmember,
a
piece

of wood (2x4x16 inches) should
be

placed
on the
hoist channel between

the adapters. This will prevent
the

adapters from damaging
the
front
sus-

pension struts.

FRONT WHEEL BEARING

ADJUSTMENT

The front wheel bearings should
be

adjusted
if the
wheel
is
loose
on the

spindle
or if the
wheel does
not
rotate

freely.
The
following procedures will

bring
the
bearing adjustment
to
speci-

fication.

DRUM BRAKES

1.
Raise
the
vehicle until
the
wheel

and tire clear
the
floor.
2.
Pry off the hub cap or
wheel

cover
and
remove
the
grease
cap (Fig.

1) from
the hu6.

3.
Wipe
the
excess grease from
the

end
of the
spindle,
and
remove
the

cotter
pin and nut
lock.

4.
While rotating
the
wheel,
hub,

and drum assembly, torque
the
adjust-

ing
nut to 17-25
ft-lbs
to
seat
the

bearings
(Fig.
4).

5.
Locate
the nut
lock
on the ad-

justing
nut so
that
the
castellations
on

the lock
are
aligned with
the
cotter

pin hole
in the
spindle.

6. Using
a 1
1/8-inch
box
wrench,

WITH WHEEL ROTATING

TORQUE ADJUSTING
NUT

TO 17-25 FT. LBS.
BACK ADJUSTING

NUT
OFF
1/2
TURN
back
off the
adjusting
nut one
half

turn. Retighten
the
adjusting
nut to

10-15 in-lbs with
a
torque wrench
or

finger tight.

7.
Position
the
lock
on the
adjust-

ing
nut and
install
a new
cotter
pin.

Bend
the
ends
of
the
cotter
pin
around

the castellated flange
of the nut
lock.

8. Check
the
front wheel rotation.

If
the
wheel rotates properly, install

the grease
cap and the hub cap or

wheel cover.
If the
wheel still rotates

roughly
or
noisily, clean, inspect
or

replace
the
bearings
and
cups
as re-

quired.

TIGHTEN ADJUSTING

NUT
TO
10-15 IN.-LBS.
INSTALL THE LOCK

AND
A
NEW COTTER
PIN

F1417-A

FIG. 4— Front Wheel Bearing Adjustmentprocarmanuals.com

03-12-03

Wheels And Tires

03-12-03

DISC BRAKES

1.
Raise the vehicle until the wheel

and tire clear the floor.

2.
Pry off the wheel cover and re-

move the grease cap (Fig. 2) from the

hub.

3.
Wipe the excess grease from the

end of the spindle, and remove the ad-

justing nut cotter pin and nut lock.

4.
Loosen the bearing adjusting nut

three turns. Then, rock the wheel,

hub,
and rotor assembly in and out

several times to push the shoe and lin-

ings away from the rotor.

5.
While rotating the wheel, hub,

and rotor assembly, torque the adjust-

ing nut to 17-25 ft-lbs to seat the

bearings (Fig. 4).

6. Back the adjusting nut off one

half turn. Then, retighten the adjust-

ing nut to 10-15 in-lbs with a torque

wrench or finger tight.

7.
Locate the nut lock on the ad-

justing nut so that the castellations on

the lock are aligned with the cotter

pin hole in the spindle.

8. Install a new cotter pin, and

bend the ends of the cotter pin around

the castellated flange of the nut lock.

9. Check the front wheel rotation.

If the wheel rotates properly, install

the grease cap and the hub cap or

wheel cover. If the wheel still rotates

roughly or noisily, clean or replace the

bearings and cups as required.

10.
Before driving the vehicle,
pump the brake pedal several times to

obtain normal brake lining to rotor

clearance and restore normal brake

pedal travel.

BALANCING LIFE

GUARD TIRE

Tires fitted with the Life Guard

Safety Spare are balanced in the same

manner as conventional tires. If an ex-

cessive out of balance condition exists

the following procedure can be used to

correct the condition:

1.
Remove the core housing and de-

flate both air chambers.

2.
Install the core housing.

3.
Unseat the beads of tire with the

bead breakers away from the valve

stem as shown in Fig. 5.

F 1383

FIG. 5—Breaking Top Bead of

Tire From Wheel Rim
4.
Rotate tire casing 90 degrees on

the wheel rim.

5.
Rotate the tire casing back and

forth on the rim to center the valve.

6. Inflate both chambers of the tire

following steps 13 through 15 of the

Tire Installation procedure.

7.
Balance the tire in the normal

manner.

CORRECTING VIBRATION

AND SHAKE-

LIFE GUARD TIRE

The condition of excessive vibration

and shake is generally the result of an

incorrect pressure relationship between

the inner and outer air chambers that

may cause the life guard to shift posi-

tion within the tire. The following

procedure should be used to correct

vibration and shake conditions:

1.
Check pressure of the inner and

outer air chambers on all four tires.

2.
If the inner chamber has at least

five psi more pressure than the outer

chamber the pressures should be ad-

justed and the tires rebalanced if nec-

essary.

3.
If the pressures of the inner and

outer air chambers are equal the Air

Container is leaking. To repair the

leaking air container the recommend-

ed procedures for the removal, repair

of air container, mounting, and bal-

ancing should be followed.

REMOVAL AND INSTALLATION

HOISTING INSTRUCTIONS

Damage to steering linkage compo-

nents and front suspension struts may

occur if care is not exercised when po-

sitioning the hoist adapters of 2 post

hoists prior to lifting the vehicle.

If a 2 post hoist is used to lift the

vehicle, place the adapters under the

lower arms or the No. 1 crossmember.

Do not allow the adapters to contact

the steering linkage. If the adapters

are placed under the crossmember, a

piece of wood (2x4x16 inches) should

be placed on the hoist channel be-

tween the adapters. This will prevent

the adapters from damaging the front

suspension struts.

WHEELS AND TIRES

WHEEL AND TIRE

REMOVAL

1.
Pry off the wheel hub cap or
wheel cover. Loosen but do not re-

move the wheel hub nuts.

2.
Raise the vehicle until the

wheel and tire clear the floor.

3.
Remove the wheel hub nuts

from the bolts, and pull the wheel

and tire from hub and drum.

F1424-
A

FIG.
6—Bead
Loosening Tool
REMOVING CONVENTIONAL

TIRE FROM WHEEL

The tire can be demounted on a

mounting machine. Be sure that the

outer side of the wheel is positioned

downward. If tire irons are used, fol-

low the procedure given here.

1.
Remove the valve cap and core,

and deflate the tire completely.

2.
With a bead loosening tool,

break loose the tire side walls from

the wheel (Fig. 6).

3.
Position the outer side of the

wheel downward, and insert two tire

irons about eight inches apart between

the tire inner bead and the back side

of the wheel rim. Use only tire irons

with rounded edges or irons designed

for removing tubeless tires.

4.
Leave one tire iron in position,

and pry the rest of the bead over the

rim with the other iron. Take small

bites with the iron around the tire inprocarmanuals.com

03-12-04

Wheels And Tires

03-12-04

order to avoid damaging the sealing

surface of the tire bead.

5.
Stand the wheel and tire upright

with the tire outer bead in the drop

center well at the bottom of the wheel.

Insert the tire iron between the bead

and the edge of the wheel rim, and

pry the wheel out of the tire.

MOUNTING CONVENTIONAL

TIRE TO WHEEL

1.
If a used tire is being installed

remove all dirt from the tire.

If a tire is being mounted to the

original wheel, clean the rim with

emery cloth or fine steel wool. Check

the rim for dents.

If a new wheel is being installed,

coat a new valve with RUGLYDE or

similar rubber lubricant and position

the valve to the new wheel. Use a rub-

ber hammer or a valve replacing tool

to seat the valve firmly against the in-

side of the rim.

2.
Apply RUGLYDE or a similar

rubber lubricant to the sealing surface

on both tire beads. With the outer

side of the wheel down, pry the beads

over the wheel rim with two tire irons.

Do not use a hammer or mallet to

force the beads over the rim.

3.
Align the balance mark on the

tire with the valve on the wheel.

4.
Hold the beads against the rim

flanges by positioning a tire mounting

band over the tire (Fig. 7). If a

mounting band is not available, tie a

tourniquet of heavy cord around the

circumference and in the center of the

tire.
Tighten the cord with a tire iron.

Center the tire on the wheel with a

rubber mallet.

F1425- A

FIG. 7—Tubeless Tire

Mounting Band

5.
Give the tire a few quick bursts

of air to seat the beads properly, then

inflate the tire to 40 psi pressure.

Check to see that the bead positioning

rings (outer rings near the side walls)

are evenly visible just above the rim

flanges all the way around the tire. If

the rings are not even, deflate the tire

completely and inflate it again.

6. When the rings are properly po-

sitioned, deflate the tire to the recom-

mended pressure.
RUBBER VALVE HOUSING

AIR CONTAINER

VALVE STEM

Ilk-
VALVE GROOVES

F 1382 . A

FIG. 8—Core Housing Disassembled

REMOVING LIFE GUARD

TIRE FROM WHEEL

1.
Mark the valve stem location on

the tire sidewall.

2.
Remove the core housing (Fig. 8)

and deflate both air chambers.

3.
Unseat the beads of the tire with

the bead breakers working away from

the valve stem (Fig. 5).

4.
Starting at the valve stem, work

the top bead of the tire over the rim

of the wheel.

5.
Pull the air container valve stem

out of the rubber valve housing (Fig.

9).

F 1384- A

FIG. 9—Removing Air Container

Valve Stem

6. Remove the air container before

attempting to remove the tire from the

wheel.

7.
Lift the lower bead over the

wheel rim to remove the tire.

8. Remove the rubber valve housing

from the wheel rim.

INSTALLING LIFE GUARD

TIRE ON WHEEL

1.
Apply Silicone Lubricant

(COAZ-19553-A) as the anti-friction

treatment uniformly over the crown

and shoulder area inside the tire or

outside the life guard.

2.
Fold the life guard as shown in

Fig. 10.
1385-
A

FIG. 70—Folding Life Guard

For Installation In Tire

3.
Insert life guard into tire casing.

4.
Install a new rubber valve hous-

ing on the air container valve stem

and thread the core housing into

place. It is not necessary to install a

new core housing.

5.
Insert air container into the life

guard with the valve grooves to the

outboard side of the tire. Place the

valve at the valve stem location

marked on the sidewall during remov-

al as shown in Fig. 11.

F 1386 • A

FIG.
7
7—Aligning Valve With

Reference Mark on Tire

6. Apply a soap solution to the

beads and the rubber valve housing.

7.
Place the wheel on the mounting

machine with the valve hole away

from bead breakers. Remove all burrsprocarmanuals.com

03-12-05
Wheels
And
Tires

03-12-05

and sharp edges from valve hole
in

rim.

8. Mount first tire bead exercising

care
not to
pinch
air
container.

9. Start valve through hole
in rim.

Do
not
pull valve housing into place

at this time.

10.
Mount
the
second bead starting

just past
the
valve
so the
last portion

of
the
bead goes over
the rim at the

valve.

11.
Rotate
the
tire back
and
forth

to center
the
valve housing.

12.
Pull
the
valve housing into

place. Make certain that
the
rubber

valve ridge
is
visible around
thi
valve

housing
(Fig.
12).

13.
Tighten
the
core housing lightly

using pliers.

14.
Thread
the
Inflate-Chek adapt-

er onto
the
core housing.
15.
Inflate
the
inner chamber
to

seat
the
tire beads exercising care
not

to exceed
45 psi
pressure. Adjust this

inner chamber
air
pressure
to 15 psi

higher than
the
recommended tire

pressure.

F 1387
- A

FIG. 12—Valve Installation
16.
Remove
the
Inflate-Chek

adapter
and
adjust tire (outer cham-

ber) pressure
to the
recommended

pressure.

17.
Recheck inner chamber pres-

sure.

18.
Install valve
cap.

WHEEL
AND
TIRE

INSTALLATION

1.
Clean
all
dirt from
the hub and

drum.

2.
Position
the
wheel
and
tire
on

the
hub and
drum. Install
the
wheel

hub nuts
and
tighten them alternately

to draw
the
wheel evenly against
the

hub
and
drum.

3.
Lower
the
vehicle
to the
floor,

and torque
the hub
nuts
to
specifica-

tion.

MAJOR REPAIR OPERATIONS

HOISTING INSTRUCTIONS

Damage
to
steering linkage compo-

nents
and
front suspension struts
may

occur
if
care
is
not
exercised when
po-

sitioning
the
hoist adapters
of 2
post

hoists prior
to
lifting
the
vehicle.

If
a 2
post hoist
is
used
to
lift
the

vehicle, place
the
adapters under
the

lower arms
or the
No.
1
crossmember.

Do
not
allow
the
adapters
to
contact

the steering linkage.
If the
adapters

are placed under
the
crossmember,
a

piece
of
wood (2x4x16 inches) should

be placed
on the
hoist channel
be-

tween
the
adapters. This will prevent

the adapters from damaging
the
front

suspension struts.

FRONT WHEEL GREASE

SEAL
AND
BEARING

REPLACEMENT AND/OR

REPACKING

If bearing adjustment will
not
elimi-

nate looseness
or
rough
and
noisy
op-

eration,
the hub and
bearings should

be cleaned, inspected,
and
repacked

with specified wheel grease.
If the

bearing cups
or the
cone
and
roller

assemblies
are
worn
or
damaged, they

should
be
replaced.

DRUM BRAKES

1.
Raise
the
vehicle until
the
wheel

and tire clear
the
floor.

2.
Remove
the
wheel cover
or hub
cap.
Remove
the
grease
cap
from
the

hub.
Remove
the
cotter
pin,
nut
lock,

adjusting
nut, and
flat washer from

the spindjej, Remove
the
outer bearing

cone
and
roller assembly
(Fig.
1).

3.
Pull
the
wheel,
hub, and
drum

assembly
off the
wheel spindle.

4.
Remove
and
discard
the
grease

retainer. Remove
the
inner bearing

Too/-T69L-J102-A

F1476-A

FIG. 13—Removing Front Wheel

Bearing Cup—Except Lincoln

Continental
cone
and
roller assembly from
the hub

with Tool 1175AE.

5.
Clean
the
lubricant
off the
inner

and outer bearing cups with solvent

and inspect
the
cups
for
scratches,

pits,
excessive wear,
and
other
dam-

age.
If
the
cups
are
worn
or
damaged,

remove them with Tool T69L-1102-A

(Fig.
13).

6. Thoroughly clean
the
inner
and

outer bearing cone
and
roller assem-

blies with solvent
and dry
them thor-

oughly.
Do not
spin
the
bearings with

compressed
air.

Inspect
the
cone
and
roller assem-

blies
for
wear
or
damage,
and
replace

them
if
necessary.
The
cone
and
roller

assemblies
and the
bearing cups

should
be
replaced
as a
unit
if
damage

to either
is
encountered.

7. Thoroughly clean
the
spindle
and

the inside
of the hub
with solvent
to

remove
all old
lubricant.

Cover
the
spindle with
a
clean

cloth,
and
brush
all
loose dust
and

dirt from
the
brake assembly.
To
pre-

vent getting dirt
on the
spindle, care-

fully remove
the
cloth from
the

spindle.

8.
If the
inner and/or outer bearing

cup(s) were removed, install
the re-

placement cup(s)
in the hub
with
the

tool shown
in Fig.
14.
Be
sure
to
seat

the cups properly
in the hub.

9. Pack
the
inside
of the hub
with

specified wheel bearing grease.
Add

lubricant
to the hub
only until
the

grease
is
flush with
the
inside diame-

ter
of
both bearing cups
(Fig.
15).procarmanuals.com

04-02-03
Rear Axle — Removable Carrier Type

04-02-03

is,
it is supported by bearings both in

front of and to the rear of the pinion

gear. Two opposed tapered roller

bearings support the pinion shaft in

front of the pinion gear with a col-

lapsible spacer for 8-3/4 inch or 9

inch ring gear, and a solid spacer used

with the 9 3/8 inch ring gear. A

straight roller (pilot) bearing supports

the pinion shaft at the rear of the pi-

nion gear. Pinion and ring gear tooth

contact is adjusted by adding or re-

moving shims from between the pinion

retainer and the carrier housing.

The differential assembly is mount-

ed on two opposed tapered roller

bearings, which are retained in the

carrier by removable caps. The entire

carrier assembly is bolted to the axle

housing.

Ball bearing assemblies (rear wheel

bearings) are pressed onto the outer

ends of the axle shafts and set in the

outer ends of the axle housing. These

bearings support the semi-floating

axle shafts at the outer ends. The

inner ends of the shafts spline to the

differential side gears. Bearing retain-

er plates hold the shafts in the hous-

ing. The left and right axle shafts are

not interchangeable, the left shaft

being shorter than the right.
CASE

COVER

BELLEVILLE

SPRING

CLUTC

HUB
STEEL

PLATES

BONDED

PLATES

E1741-A

FIG. 2—Limited-Slip Differential

LIMITED-SUP DIFFERENTIAL

The axle assembly, except for the

differential case and its internal com-

ponents, is identical to the convention-

al axle.

A constant-friction locking differen-

tial,
which employs clutch plates to

control differential action, is available

as optional equipment (Fig. 2).

Four steel clutch plates are locked

into the differential cover. Three

bronze, bonded clutch plates are

splined to a clutch hub which, in turn,
is splined to the left axle shaft. A

Belleville spring washer maintains a

constant pressure between the steel

and bonded clutch plates so that the

clutch is always engaged.

TRACTION-LOK

DIFFERENTIAL

The Traction-Lok (torque sensitive)

locking differential (Fig. 3) employs a

multiple disc clutch to control differ-

ential action. Shim(s), which control

side gear mounting distance, four

steel, four friction and one composite

plate (steel on one side and friction

material on the other) stacked on a

clutch hub, and four ear guides are

housed in the differential cover. Lo-

cated in the differential case between

the side gears is a one-piece pre-load

plate and block (four-pinion) and four

calibrated pre-load springs, which

apply an initial force to the clutch

pack. Additional clutch capacity is

derived from the side gear thrust

loads.
The four friction plates are

splined to the clutch hub which in turn

is splined to the left axle shaft, and

the eared steel plates are dogged to

the case; thus, the clutch is always en-

gaged.

PINION SHAFT

4211

PINION SHAFT

RETAINING PINS

359475-S
DIFFERENTIAL

CASE-4204

CASE-TO-COVER

RETAINING SCREWS

50025-S2

SIDE GEAR

THRUST WASHER

4228

CENTER BLOCK

(SHORT PINION PINION

SHAFT SEAT) SHAFT

4420 44207
7
PINION GEAR

THRUST WASHER

4230

PINION GEARS

4215

PINION GEAR

THRUST WASHER

4230

PINION SHAFT

44207
SHIM(S)

(AS REQ'D.)

4A324

DIFFERENTIAL

CASE COVER

4204

PINION GEAR

THRUST WASHER

4230
PRE-LOAD SPRING

PINION GEAR PLATE-4A326

THRUST WASHER

4230

CLUTCH PLATE

EAR GUIDES
(4)

4A323

E 1896-A

FIG. 3—Traction-Lok Differentialprocarmanuals.com