FORD MUSTANG 2003 Workshop Manual

LH mount
18. Remove the nuts and detach the ground cables.
19. Remove the bolt, the studbolts and the engine mount.
Installation
LH mount 1. Position the engine mount and install the bolt and studbolts. Klj . 5 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2. Attach the ground cables and install the nuts.
RH mount 3. Position the engine mount and install the bolts and studbolt.
4. Attach the wiring harness and install the nut. Both mounts Klj . 6 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

5. Using the jackstands, raise the subframe into position.
6.
NOTE: RH shown, LH similar.
Using the special tool, align the subframe.
7. NOTE: RH shown, LH similar.
Install the four bolts.
8. NOTE: RH shown, LH similar.
Install the four bolts.
9. Remove the jackstands. Klj . 7 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

10.
NOTE: RH shown, LH similar.
Install the two engine mount nuts.
11. Position the cross- brace support and install the 13 bolts.
12. NOTE: RH shown, LH similar
Install the six splash- shield pushpins. Klj . 8 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

13. Install the front springs. For additional information, refer to
Section 204 - 01 .
14. Remove the special tool.
15. Remove the special tool.
16. Position the generator and install the bolts.
17. Connect the generator electrical connections. Klj . 9 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

18. Rotate the drive belt tensioner clockwise and attach the drive belt to the generator pulley.
zMake sure the drive belt is routed correctly and is aligned correctly installed on each
pulley.
19. Connect the battery ground cable. For additional information, refer to Section 414 - 01 .
20. Install the coolant bypass tube. For additional information, refer to Section 303 - 03A . Klj . 10 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL
Engine
Removal
All vehicles
1. Disconnect the battery ground cable. For additional information, refer to Section 414 - 01 .
2. Remove the hood- to-body ground strap.
3. NOTE: Mark the hood hinge locations to aid in hood installation.
Remove the four nuts and the hood.
SECTION 303-
01D: Engine — Mach I 4.6L (4V) 2003 Mustang Workshop Manual Special Tool(s)
Lifting Bracket, Engine
303-
D087 (D93P-6001- A1) Lifting Bracket, Engine
303-
D088 (D93P-6001- A2) Spreader Bar
303-
D089 (D93P-6001- A3) Klj . 1 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. Recover the A/C system. For additional information, refer to
Section 412 - 00 .
5. Remove the air intake scoop bracket. For additional information, refer to Section 303 - 12 .
6. Disconnect the air cleaner outlet pipe at the throttle body. 1. Disconnect the positive crankcase ventilation (PCV) inlet tube.
2. Loosen the clamp and disconnect the outlet pipe.
7. Disconnect the mass airflow sensor electrical connector.
8. Remove the air cleaner. 1. Remove the bolt.
2. Remove the air cleaner and the outlet pipe as an assembly. Klj . 2 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9. Disconnect the electrical connector.
10. Drain the engine cooling system. For additional information, refer to Section 303 - 03A .
11. Disconnect the fuel tube spring lock coupling. For additional information, refer to Section 310 -
00 .
12. Remove the upper radiator hose (8260).
13. Disconnect the throttle cable, and the speed control cable, and remove the throttle return spring. Klj . 3 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

14. Remove the bolts and detach the retainer. Position the cables and the bracket aside.
15. Disconnect the evaporative emissions return line.
16. Disconnect the 16-
pin and the 42-pin connectors.
17. Separate the engine control sensor wiring in three locations and position onto the engine.
18. Disconnect the vacuum hoses. Klj . 4 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...