FORD MUSTANG 2003 Workshop Manual

Page 1741 of 4378

19. Disconnect the heater hoses.
20. Remove the wiring support bracket.
21. Disconnect the connectors.
22. Raise the cover and remove the nut and cables. Klj . 5 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 1742 of 4378

23. Disconnect the hose from the coolant bypass tube.
24. Disconnect the A/C suction tube from the accumulator.
25. Disconnect and remove the A/C suction tube.
26. Disconnect the A/C tube. Position A/C tube aside. Klj . 6 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 1743 of 4378

27.
NOTE: The lifting bracket bolts will be installed when the vehicle is raised.
Position the RH lifting bracket.
28. Install the LH lifting bracket.
29. Disconnect the radiator vent hose from the degas bottle.
30. Remove the degas bottle return hose. Klj . 7 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 1744 of 4378

31. Remove the nuts and the degas bottle
32. Remove the shifter. For additional information, refer to
Section 307 - 01 or
Section 308 - 03B .
33. Remove the dual converter H- pipe. For additional information, refer to Section 309 - 00 .
34. Drain the engine oil. zInstall the drain plug when finished.
35. Position the A/C muffler aside. 1. Remove the bracket retainer.
2. Disconnect the A/C tube and position the A/C muffler aside. Klj . 8 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 1745 of 4378

36. Index-
mark the driveshaft flange and the rear axle pinion flange.
37. Remove the four bolts
38. Index- mark the driveshaft at the six o'clock position.
39. CAUTION: the driveshaft flange fits tightly on the rear axle pinion flange pilot. Never
hammer on the driveshaft or any of its components to disconnect the driveshaft flange
from the pinion flange. Pry only in the area shown, with a suitable tool, to disconnect the driveshaft flange from the pinion flange. Klj . 9 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 1746 of 4378

NOTE:
Do not rotate the driveshaft.
Using a suitable tool, disconnect the driveshaft flange from the rear axle flange and remove the
driveshaft.
40. Index- mark the transmission output shaft at the six o'clock position.
41. Remove the starter motor terminal cover.
42. Disconnect the starter wiring. 1. Remove the nut and disconnect the battery positive cable.
2. Remove the nut and disconnect the starter solenoid wire. Klj . 10 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 1747 of 4378

43. Remove the three bolts and the starter.
Automatic transmission vehicles 44. Remove the flywheel inspection cover.
45. Remove the torque converter nuts. All vehicles Klj . 11 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 1748 of 4378

46. Remove the nut and the wiring harness bracket.
47. Remove the nuts and position the wiring harness aside.
48. Disconnect the oil pressure sensor.
49. Remove the nut and the engine ground cable.
50. Disconnect the hose from the oil filter adapter. Klj . 12 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 1749 of 4378

51. Disconnect and remove the lower hose from the radiator.
52.
NOTE: Drain the power steering fluid into a suitable container.
Disconnect the hose from the power steering reservoir.
53. Remove the bolt and the anti- rotation clip.
54. Loosen the fitting and disconnect the high pressure hose from the power steering pump. Klj . 13 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 1750 of 4378

55. Remove the ground strap bolt.
56. Remove the degas bottle support bracket.
57. Install the two bolts from the RH lifting bracket.
58. Disconnect the reversing lamp switch electrical connector, and the wiring harness from the
transmission. Klj . 14 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page:   < prev 1-10 ... 1701-1710 1711-1720 1721-1730 1731-1740 1741-1750 1751-1760 1761-1770 1771-1780 1781-1790 ... 4380 next >