diagram INFINITI QX4 2001 Factory Service Manual
Page 1300 of 2395
Wiring Diagram Ð WARN ÐNBEL0050
MEL795L
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING LAMPS
Wiring Diagram Ð WARN Ð
EL-115
Page 1301 of 2395
MEL796L
WARNING LAMPS
Wiring Diagram Ð WARN Ð (Cont'd)
EL-116
Page 1302 of 2395
MEL006O
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING LAMPS
Wiring Diagram Ð WARN Ð (Cont'd)
EL-117
Page 1303 of 2395
MEL798L
WARNING LAMPS
Wiring Diagram Ð WARN Ð (Cont'd)
EL-118
Page 1304 of 2395
MEL215M
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING LAMPS
Wiring Diagram Ð WARN Ð (Cont'd)
EL-119
Page 1305 of 2395
MEL799L
WARNING LAMPS
Wiring Diagram Ð WARN Ð (Cont'd)
EL-120
Page 1306 of 2395
MEL800L
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING LAMPS
Wiring Diagram Ð WARN Ð (Cont'd)
EL-121
Page 1307 of 2395
SEL062WA
Fuel Warning Lamp Sensor CheckNBEL01661. Turn ignition switch ªOFFº.
2. Disconnect fuel level sensor unit harness connector B12.
3. Connect a resistor (80W) between fuel tank gauge unit harness
connector terminals 2 and 3.
4. Turn ignition switch ªONº.
The fuel warning lamp should come on.
NOTE:
ECM might store the 1st trip DTC P0180 during this inspection.
If the DTC is stored in ECM memory, erase the DTC after recon-
necting fuel tank gauge unit harness connector.
Refer to EC-60, ªHOW TO ERASE EMISSION-RELATED DIAG-
NOSTIC INFORMATIONº.
MEL425F
Electrical Components InspectionNBEL0051OIL PRESSURE SWITCH CHECKNBEL0051S02
Oil pressure
kPa (kg/cm2, psi)Continuity
Engine startMore than 10 - 20
(0.1-0.2,1-3)NO
Engine stopLess than 10 - 20
(0.1-0.2,1-3)YES
Check the continuity between the terminals of oil pressure switch
and body ground.
SEL901F
DIODE CHECKNBEL0051S03ICheck continuity using an ohmmeter.
IDiode is functioning properly if test results are as shown in the
figure at left.
ICheck diodes at the combination meter harness connector
instead of checking them on the combination meter assembly.
Refer to EL-115, ªWARNING LAMPº wiring diagrams.
NOTE:
Specification may vary depending on the type of tester. Before
performing this inspection, be sure to refer to the instruction
manual for the tester to be used.
WARNING LAMPS
Fuel Warning Lamp Sensor Check
EL-122
Page 1308 of 2395
Wiring Diagram Ð AT/IND ÐNBEL0203
MEL801L
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
A/T INDICATOR
Wiring Diagram Ð AT/IND Ð
EL-123
Page 1309 of 2395
MEL802L
A/T INDICATOR
Wiring Diagram Ð AT/IND Ð (Cont'd)
EL-124