204 JAGUAR X308 1998 2.G Workshop Manual

Yes

Vehicle is OK.
No GO to J2
.
J
2: CHECK BRAKE FLUID LEVEL
Check the brake master cyli

nder reservoir fluid level.
1
Is the fl

uid level OK?
Yes GO to J3
.
No

CHECK brake master cylinder reservoir sealing points. For additional information, refer to Brake
Master Cylinder in this section. ADD brake fl uid and BLEED the brake system. For additional
information, refer to General Proc edures in this section. TEST the system for normal operation.
REPEAT road test if necessary.
J
3: CHECK BRAKE PEDAL RESERVE
Engine is

idle.
1
Apply the brake pedal ligh

tl
y three or four times.
2
W
ait 15 seconds for the vacuum to replenish.
3
Push down on

the brake pedal until it stops moving
downward or an increased resistance to the brake
pedal travel occurs.
4
Hol
d the brake pedal in the applied position while increasing the engine speed to 2000 revs/min.
5
Re

lease the accelerator pedal.
6
Does th

e brake pedal move downward as
the engine speed returns to idle?
Yes GO to J4
.
No

CHECK the vacuum to the brake booster. Fo r additional information, refer toSection 206
-0
7 Power
Brake Ac

tuation
.
J

4: CHECK THE FRONT HUB AND BEARING ASSEMBLY
Check the fr

ont hub and bearing assembly. Fo
r additional information, refer toSection 204
-01
Front
Suspe

nsion
. 1
Are th

e front wheel bearings loose?
Yes INSTALL a new front wheel bearin g if damaged. For additional information, refer toSection 204
-01

F

ront Suspension
. TEST
the system for normal operation.
No CHECK the front brake discs for thickness variances. For additional information, refer to General
Procedures in this section.
PINPO
INT TEST K : SLOW OR INCOMPLETE BRAKE PEDAL RETURN
TE
ST
CONDITIONS
D
ETAILS/RESULTS/ACTIONS
K1: C

HECK FOR BRAKE PEDAL RETURN
Ru

n the engine at fast idle while
making several brake applications.
1
Pull the
brake pedal rearward with approximately 44.5 N (10lb) force.
2
Relea

se the brake pedal and measure
the distance to the toe board.
3
Make a hard brake
application.
4
Relea

se the brake pedal and measure the brake
pedal to toe board distance. The brake pedal
should return to its original position.
5
Does th
e brake pedal return
to its original position?
Yes Vehicle is OK.
No GO to K2
.
K
2: CHECK FOR BRAKE PEDAL BINDING
Check the brake pedal to make
s
ure it is operating freely.
1
Is th

e brake pedal operating freely?
Yes INSTALL a new brake booster. For addi tional information, refer toSection 206
-0
7 Power Brake
Actuation. TEST

the system for normal operation.
No REPAIR or INSTALL new brake pedal. TE ST the system for normal operation.

Brake System - Gener
al Information - Front Brake Disc Runout
CheckVehicles With: Standard Brakes
Gen e
ral Procedures
S
p
ecial Tool(s)

Dial Test Indicator
G
auge and Stand.
1. Raise front of vehicle and support on stands. Refer to section
100-02.
2. Remove wheel.

3. CAUT
ION: Tie caliper housing aside. Do not allow the
caliper housing to hang on the hydraulic hose, as this will damage
the hose.
Remove caliper housing from caliper carrier.
1. Remove anti-rattle spring.
2. Remove dust covers.
3. Remove guide pins.
Remove an
d tie caliper housing aside.
4.
Make sure that wheel
bearing en
d-float is correct. Refer to
specification section 204-01.

5. Measure brake d
isc run-out.
Inst
al
l brake disc to hub and secure with all wheel nuts,
tighten wheel nuts to 20 Nm in a diagonal sequence.
Posi
tion the gauge so that the pointer contacts the disc,
10 mm from its outer edge.
Slo w
ly rotate the disc one revolution, the disc run-out
must not exceed the specification. Refer to Specification
Section 206-03.
6. If the brake disc run-out exceeds specification, reposition the
brake disc on the hub and re peat the above procedure.
Continue repositioning the brake di sc until the run-out is within
specification.
7. If the brake disc run-out still exceeds specification, check the
hub face run-out.
8. Remove brake disc. Refer to procedure 70.10.12.
9. Measure hub face run-out.
Posi
tion the gauge so that the pointer contacts the hub
face.
Slo w
ly rotate the hub one revolution, the hub run-out

mu
st not exceed the specification. Refer to Specification
Section 204-01.
I
f the hub exceeds the maximum run-out specification
replace the hub. Refer to procedure 60.25.01.
10. NOTE: Make sure the brake disc and hub mating surfaces are
clean.
If the hub run-out is within sp ecification replace brake discs.
Refer to procedure 70.10.12.

11
.
Install caliper housing to caliper carrier.
Align hou
sing to carrier.
1. Install and tighten guide pins to 25-30 Nm.
2. Install dust covers.
3. Install anti-rattle spring.
12. Install wheel. Refer to procedure 74.20.05.

R
emove and tie caliper aside.
5. Make sure that wheel bearing end-float is within specification. Refer to specification section <<204-01>>.
6.
Measure brake disc run-out.
1. Install brake disc to hub and secure with all wheel nuts, tighten wheel nuts to 20 Nm in a diagonal sequence.
2. Position the gauge so that the pointer contacts the disc, between the disc's outer drill holes and the disc's outer edge.
 Slowly rotate the disc one revolution, the disc run-out must not exceed the specification. Refer to
Specification Section <<206-03>>.
7. If the brake disc run-out exceeds specification, reposition the brake disc on the hub and repeat the above
procedure. Continue repositioning the brake disc until the run-out is within specification.
8. If the brake disc run-out still exceeds specification, check the hub face run-out.
9. Remove brake disc.

1
0. Measure hub face run-out.
Position the gauge so that the pointer contacts the hub face.
 Slowly rotate the hub one revolution, the hub run-out must not exceed the specification. Refer to
Specification Section <<204-01>>.
 If the hub exceeds the maximum run-out specification replace the hub. Refer to procedure 60.25.01.
11. NOTE:
Make sure the brake disc and hub mating surfaces are clean.
If the hub run-out is within specification replace the brake discs. Refer to procedure 70.10.12.
12. When the disc run-out is within specification, index mark the hub and disc for future installment.
1
3. Install caliper to vertical link.
Install and tighten bolts to 140 Nm.

Me
asurement of the brake disc run-out, must be carried-out with the disc and hub parking-brake
adjuster-holes aligned.
Make sure that wheel bearing end-float is correct. Refer to specification section <<204-02>>.
5.
Measure brake disc run-out.
 Install brake disc to hub and secure with all wheel nuts, tighten wheel nuts to 20 Nm in a diagonal
sequence.
 Position the gauge so that the pointer contacts the disc 10 mm from its outer edge.
 Slowly rotate the disc one revolution, the disc run-out must not exceed the specification. Refer to
specifications in section <<206-04>>.
6. If the brake disc run-out exceeds specification, check the hub face run-out.
7. Remove brake discs. Refer to procedure 70.10.13.
8.
Measure hub face run-out.



Position the gauge so that the pointer contacts the hub face.
 Slowly rotate the hub one revolution, the hub run-out must not exceed the specification. Refer to
Specification Section <<204-01>>.
 If the hub exceeds the maximum run-out specification replace the hub. Refer to Section <<204-01>>.
9. NOTE:
Make sure the brake disc and hub mating surfaces are clean.
If the hub run-out is within specification replace brake discs. Refer to procedure 70.10.13.
1
0. Install caliper housing to caliper carrier.
1. Align housing to carrier.
2. Install and tighten guide pins to 25-30 Nm.
3. Install dust covers.
4. Install anti-rattle spring.
11. Fit wheel. Refer to section <<204-04>>.

5.
Make sure that wheel bearing end-float is within specification. Refer to specification section
<<204-02>>.
6.

NOTE:
Measurement of the brake disc run-out, must be carried-out with the disc and hub access holes aligned.
7.
Measure brake disc run-out.
1. Install brake disc to hub and secure with all wheel nuts, tighten wheel nuts to 20 Nm in a diagonal sequence.
2. Position the gauge so that the pointer contacts the disc, between the disc's outer drill holes and the disc's outer edge.
 Slowly rotate the disc one revolution, the disc run-out must not exceed the specification. Refer to
specifications in section <<206-04>>.
8. If the brake disc run-out exceeds specification, check the hub face run-out.

9
. Remove brake discs. Refer to procedure 70.10.13.
1

0. Measure hub face run-out.
Position the gauge so that the pointer contacts the hub face.
 Slowly rotate the hub one revolution, the hub run-out must not exceed the specification. Refer to
Specification Section <<204-02>>.
 If the hub exceeds the maximum run-out specification replace the hub. Refer to operation
<<64.15.14>> .
11. If the hub run-out is within specification replace brake discs. Refer to procedure 70.10.13.
1
2. Install caliper to hub carrier.
Install and tighten bolts to 60 Nm.

13
.
CA
UTION:
Retracting the caliper piston may cause the fluid reservoir to over-flow. Remove brake fluid
spillage immediately from paint work with clean water.
CA
UTION:
Note condition of pins and replace if necessary.
Install brake pads to caliper. Slowly retract caliper pistons.
1. Install pads.
2. Position anti-rattle spring.
3. Install pins - make sure pin collets are fully engaged into caliper.
14. Fit wheel. Refer to section <<204-04>>.