204 JAGUAR X308 1998 2.G Manual Online

9. Se
cure the shock absorber
to the upper mounting.
Posi
tion a wrench on the shock absorber shaft flats to
prevent rotation (wrench in socket on vehicles with
adaptive damping).
Tigh
ten the shock absorber upper lock nut to 30-40 Nm
(16-18 Nm on vehicles with adaptive damping).
10. Position the shock absorber and spring assembly to the
vehicle.

11
.
With assistance, manually re tract the shock absorber and
remove the temporary securing bolt.

12
.
Remove the special tools 204-179-1.
13. Align the shock absorber lower bush to the wishbone and
install the mounting bolt.
1. Install but do not tighten the nut.

14. CAUTI
ON: Make sure the adaptive damping electrical
connector is correctly aligned. Failu re to follow these instructions
may cause damage to the electrical connector.
On vehicles with adaptive damping:
Conne ct
the shock absorber elec
trical connector, ensuring
the electrical connector key locates in the socket keyway.

15 . Seat
the upper mounting in the body location.
1. If adaptive damping is installed, ensure the harness is
correctly positioned.

16 . Ensuri
ng that the spri
ng is seated on the isolator and spring
pan, position the u pper spring pan on to the body studs.
17. Release the spring tension.
Ensuring that the spri
ng is
correctly located, evenly
slacken the adjuster bolts on the special tools 204-179.

18
.
Remove the special tools 204-179.

19
.
Fully seat and secure the u pper spring pan to the body.
Ensure the spri
ng pan is correctly seated in the body
location.
Inst
all the nuts securing the sp
ring pan to the body studs.

Tigh
ten to 17-23 Nm.

20
.
Tighten to 80-100 Nm.

21
.
Install the shims on the pivot pin sleeve in the positions
noted during removal.
22. Install the hub assembly to the wishbone assembly.
Position the hub and carri
er to the wishbone.
Inst

all the pivot pin ensuring that the ecce
ntric flange
correctly seats in the wishbone groove.

28
.
Install the rear wheel.
For additional informat ion, refer to Section 204
-04
Wheels and
Tire

s
.
29
.
Remove the axle stands and lower the vehicle.
For additional informat ion, refer to Section 100
-0
2 Jacking and
Liftin

g
.
30
.
Check and adjust the rear whee l alignment as necessary.
For additional informat ion, refer to Section 204
-00
Suspension
Sy

stem
- General
Information
.

Rear
Suspension -
Stabilizer Bar Mounting Frame Bushing
Re
moval and Installation
Remov

al
CAUTI
ON: Replacement of
nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
I
nstallation
S
pecial Tool(s)

Adaptor Rin

g
204-116-01 (JD 143-1)

Anvil Adaptor
2
04-116-02 (JD 143-2)

R

emover/Replacer Adaptor
204-116-08 (JD 143-8)

D
ifferential Strut - Bush Replacer
204-201 (JD 241)
1. R
emove monostrut from
vehicle. Refer to operation 64.25.12.

2. Using a h
ydraulic press remove bush from monostrut.
Using special tools,

support monostrut on the press bed.
Posit

ion special tool on top of bush and align tool with
press ram.
Press bush from monostrut.

3. Clean relevant parts.
1. Using a hydraulic press, fi t bush into monostrut.
S
upport the bush-bore of the monostrut between
plates on the press-bed.

Rear
Suspension - Rear Wheel Bearing
Re
moval and Installation
S

pecial Tool(s)

Hub Holdin

g Tool
204-195 (JD227)

Hub Pu
ller
204-011 (JD 1D)

R
ear-Hub Remover
204-113 (JD 132)

Bearing Cu
p Replacer Adaptor
204-118 (JD 550-4/1)

Bearing Cu
p Replacer Adaptor
204-118 (JD 550-4/2)

D
river Handle
100-013 (18G-134)

Rear-hub spacer
replacer
204-003 (JD 15)
O
il Seal Remover/Replacer

Remova
l

2
05-2
34 (JD 550-1)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used. See section 100-00 for information.
Release handbrake.
2. Ra
ise the vehicle on a four-post lift.

3. Fully slacken bu
t do not remove parking brake cable adjuster
nut.

4. Relea s
e appropriate side parkin
g brake cable from connecting
clip.

5. With draw parkin
g brake cable th
rough equalizer (LH side cable
only).
6. Lower four-post lift.
7. Raise rear of vehicle to workin g height and support on stands.
Refer to section 100-02.
8. Remove rear wheel. Refer to section 204-04.

9. P
osition special tool 204-195 on hub studs and install securing
nuts.

10
.
Slacken but do not remove hub to axle shaft securing nut.
11. Remove securing nuts and withdraw special tool (204-195)
from hub.
12. Remove rear brake disc. Refer to 70.10.13.
13. Remove parking brake shoe s. Refer to 70.40.05.

14
.
Remove wheel speed sensor.
Disc
onnect wheel speed sensor harness from sensor
R

emove wheel speed sensor se
curing bolt and withdraw
sensor from hub carrier.

15
.
Sever and discard wheel speed sensor harness tie strap and
position harness for access.
16. Remove hub nut and collar.
Re
move nut.

Remove l
ocating collar.

17 . Install a th
read protector on axle shaft.

18 . R
elease hub from axle shaft.
Pos
i
tion hub puller 204-011 on hub studs.
Inst
al
l securing nuts.
Progres
s
ively tighten
puller center bolt to release hub from
axle shaft splines.
19. Remove hub puller an d thread protector.
Re
move securing nuts and
release puller from hub.
Re
move thread protecto
r from axle shaft.

20 . Relea
se parking brake cable
from suspension mounting
bracket.
Remove cable reta ining clip.

Draw c
a
ble through suspension mounting bracket
aperture.
21. Remove parking brake cable to hub carrier grommet.

26. CAUTI
ON: Note position of
shims during removal. They
must be returned to their original positions during installation.
Noting positions, remove shim from each end of pivot pin
sleeve.

27 . W
ithdraw pivot pin sleeve from hub carrier.

28 .
Using a h
ydraulic press,
remove hub from carrier.
Plac
e large section of special tool 204-113 on press bed,
with recess in t ool uppermost.
Positi
on hub carrier on tool
, ensuring handbrake cable
housing locates in tool recess.
Posit i
on small section of special tool on hub. 204-113.
Align to
ol to press-r
am, and
operate press to remove hub
from hub carrier.
29. Place hub carrier on a work bench.
30. Withdraw ABS rotor from hub carrier.