glove box JAGUAR X308 1998 2.G User Guide

Instrument Panel and Console - Floor Console Stowage Compartment
Removal and Installation
Removal
Installation

1.
Open console gl ove box lid.

2. Slacken and remove the glove box lid stay securing screw and
remove lid stay.

3. Slacken and remove glove box latch securing screws and
remove latch assembly.

4. Slacken and remove glovebox liner rear securing screws.
5. Remove glovebox liner from vehicle.
1. Position glovebox liner in console.
2. Fit and tighten liner rear securing screws.
3. Position latch assembly on line r and fit and tighten securing
screws.
4. Fit and tighten check arm to lid securing screw.
5. Position lid to stay and fit and tighten securing screw.
6. Close glovebox lid.

Instrument Panel and Console - Floor Console Stowage Compartment Lid
Removal and Installation
Removal
1. Open glovebox lid.

2. Slacken and remove lid stay se curing screw and remove stay from lid.

3. Slacken and remove glovebox latch securing screws and
remove latch from glovebox.

4. Slacken and remove glovebox li ner rear securing screws and
remove liner for access.

5. Slacken and remove remaining gl ovebox hinge securing screw.

Installation

6.
Slacken and remove screws securing hinge to lid and remove
hinge.
1. Position hinge on console lid and fit and tighten securing
screws.
2. Position glovebox lid on cent re comsole and fit and tighten
securing screw.
3. Fully seat liner in centre co nsole and fit and tighten rear
securing screws.
4. Fit glovebox latch to liner and fit and tighten securing screws.
5. Position glovebox to lid stay, fi t and tighten securing screw and
close glovebox lid.

Instrument Panel and Console - Glove Compartment
Removal and Installation
Removal
Installation

1.
Open glovebox.

2. Supporting the glovebox, slac ken and remove the four top
securing screws.

3. Slacken and remove the two glovebox lower outer securing
screws.

4. Withdraw glovebox for access and disconnect the two
illumination harness connectors.
5. Remove glovebox from vehicle.
1. Position glovebox for access and connect illumination harness.
2. Position and fully seat glovebox.
3. Fit but do not tighten the lower securing screws.
4. Fit and fully tighten the upper securing screws.
5. Close glovebox lid.
6. Fully tighten the lower securing screws.

Instrument Panel and Console - Glove Compartment Lid
Removal and Installation
Removal
Installation

1.
Remove glovebox. Refer to 76.52.03.

2. Open glovebox lid and lift barbed hook to release damper
cord loop from lid..
3. Slacken and remove the two lid hinge securing nuts.
4. Remove glovebox lid.
1. Fit glovebox lid to liner.
2. Position lid on hinges and fi t but do not tighten securing
screws.
3. Fit damper cord loop to lid.
4. Position and fit glovebox. Refer to 76.52.03.
5. Adjust lid position to achieve satisfactory all-round clearance
and catch operation.
6. Fully tighten hinge securing screws.

Instrument Panel and Console - Glove Compartment Lid Damper
Removal and Installation
Removal
Installation

1.
remove glovebox assembly. Refer to 76.52.03.

2. Disconnect glovebox damper cord end loop from damper and
route cord through the liner guide.

3. Slacken and remove the two damp er securing nuts and remove damper from liner.
1. Position damper on liner
2. Fit and tighten damper securing nuts.
3. Route damper cord through liner guide and connect end loop to
damper.

Instrument Panel and Console - Glove Compartment Liner
Removal and Installation
Removal
Installation

1.
Remove glovebox refer to 76.52.03.
2. Remove glovebox lid. Tefer to 76.52.02.
3. Remove glovebox damper. Refer to 76.52.22.

4. Release damper cord guide retaining tangs and remove guide
from bracket.

5. Position liner for access and ca refully remove switch assembly
from housing.
1. Route illumination switch harness into switch housing.
2. Connect switch to harness mult iplugs and fit and fully seat
switch in housing.
3. Secure harness in liner clips.
4. Fit lid damper to liner. Refer to 76.52.22.
5. Fit damper cord guide to bracket.
6. Route damper cord through guide and connect to damper.
7. Fit glovebox lid. refer to 76.52.02.
8. Fit glovebox. Refer to 76.52.03.

Instrument Panel and Console - Instrument Panel
Removal and Installation
Removal
1. Turn ignition switch to position II.
2. Motor driver and front passenger seats rearward.
3. Position steering wheel in stra ight ahead position and fully
lower and extend steering column.
4. Turn ignition switch to position O.
5. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
6. Remove 'J' gate finish er. Refer to 76.25.24.
7. Remove 'J' gate finisher retain ing panel. Refer to 76.25.26.
8. Remove centre console veneer panel. Refer to 76.47.26.
9. Disconnect and remove radio.
10. Remove centre console switch module. Refer to 86.80.32.
11. Remove centre console. Refer to 76.25.01.

12. Slacken and remove centre cons ole vent duct rear securing
screw and withdraw duct assemb ly from air conditioning unit
manifold.
13. WARNING: BEFORE ANY AIRBAG/SRS SERVICE IS
PERFORMED, AT LEAST ONE MINUTE MUST ELAPSE AFTER
DISCONNECTION OF THE BATTERY CABLE, TO ALLOW
DISSIPATION OF BACK-UP POWER SUPPLY ENERGY.
Remove driver airbag. Refer to 76.73.39.
14. Remove steering wheel. Refer to Section 211-04.
15. Remove steering column lo wer cowl. Refer to 76.46.03.
16. Remove steering column u pper cowl. Refer to 76.46.02.
17. Remove driver side unders cuttle. Refer to 76.46.11.
18. Remove combined windshield wiper/washer switch and
audible warning speaker assembly. Refer to 86.65.42.
19. Remove glovebox. Refer to 76.52.03.
20. Remove 'A' post lower trim pads. refer to 76.13.30.
21. Carefully withdraw driver stowage bin trim, remove bin
securing screw and remove bin from facia.

46. Connect passenger side facia harness to passenger
compartment harness multiplug and secure with retaining
lever.
47. Install trim pad on passenger side lower 'A' post. Refer to
76.13.30.

48. Connect passenger air bag link harness multiplug.
49. Install passenger glovebox assembly. Refer to 76.52.03.
50. Install 'J' gate assembly. Refer to 76.25.24 and 76.25.26.

51. Position centre console rear vent duct in air conditioning unit
and install rear securing screw.
52. Install centre console. Refer to 76.25.01.
53. Install centre console switch module. Refer to 76.13.30.

Instrument Panel and Console - Rear Cup Holder
Removal and Installation
Removal
Installation
1. Remove the console glove box lid. Refer to 76.25.18.

2. Slacken and remove the ten inner lid securing screws. and
remove the inner lid.

3. Slacken and remove cupholder latch securing screw and
remove latch assembly.

4. Open cupholder, depress tang each side of latch location and
withdraw cupholder assembly. from base.

5. Slacken and remove the cupholde r trim panel securing screws.