ECU JAGUAR X308 1998 2.G Workshop Manual

Interior Trim and Ornamentation - Parcel Shelf
Removal and Installation
Removal
Installation

1.
Open both rear doors.
2. Remove rear seat cushion. Refer to 76.70.37.
3. Remove rear seat squa b. Refer to 76.70.38.

4. Remove and discard the two fir tr ee fasteners securing front of
tray to parcel shelf.
5. Remove parcel tray.
Slightly raise front of shelf trim and lift rear fold clear of
body flange.
Exercising care to avoid dama ging sun blind (if fitted) and
rear quarter trims, or dislodging high level stop lamp, slide trim from shelf, twist slightly and remove from vehicle via
rear doors.
1. Exercising care to avoid damaging sun blind (if fitted) and rear
quarter trims, or dislodging hi gh level stop lamp, slide trim
onto shelf, engaging rear fold on body flange.
2. Secure front of trim to shelf using two new fir tr ee fasteners.
3. Fit rear seat squab. Refer to 76.70.38.
4. Fit rear seat cushion. Refer to 76.70.37.

Interior Trim and Ornamentation - Parcel Shelf Support
Removal and Installation
Removal
Installation

1.
Remove rear parcel tray. Refer to 76.67.06.90
2. Place parcel tray face down on clean bench.

3. Where sun blinds are fitted:
1. Slacken and remove nuts securing sun blind to parcel tray.
2. Remove washers.
3. Remove sun blind from parcel tray.

4. Remove eight clips securing parc el tray outer panel to inner
panel and separate panels.
1. Align outer panel to inner panel
2. Secure panels together with eight clips.
3. Where sun blinds are to be fitted, position rollers on underside
of parcel tray, fit washers and fit and tighten nuts to 5-7Nm.
4. Fit parcel tray. Refer to 76.67.06.90.

Interior Trim and Ornamentation - Passenger Assist Handle
Removal and Installation
Removal
Installation



1. Using a piece of wood or simila rly soft material, press inner
end of each screw cover to release outer clip.
2. Remove screw covers , slacken and remove securing screws
and remove grab handle from cantrail.
1. Position grab handle and coat hanger hook at cantrail
2. Ensuring that cantrail trim pads are correctly aligned, fit and
tighten the grab handle securing screws.
3. Slide each screw cover inner end foremost, onto end of grab
handle and press outer end to engage clip.

Interior Trim and Ornamentation - Rear Door Armrest Removal and Installation
Removal
Installation

1.
Remove battery cover and disconnect ground cable from battery
terminal. Refer to 86.15.19.
2. Remove door casing. Refer to 76.34.01.

3. Slacken and remove four screws se curing armrest to door casing
and remove armrest from casing.

4. Remove switchpack/ashtray from armrest.
1. Slacken and remove two screws securing switchpack/ashtray and finisher to armrest.
2. Remove switchpack/ashtray and finisher from armrest.

5. Slacken and remove two screws secu ring armrest retaining clip and
remove clip from armrest.
1. Position retaining clip on armrest and fit and tighten securing
screws.
2. Position switchpack/ashtray and finisher on armrest and fit and
tighten securing screws
3. Position armrest on casing and fit and tighten four securing screws.
4. Fit casing to door. Refer to 76.34.04.
5. Connect ground cable to battery and fit battery cover. Refer to
86.15.15.

Interior Trim and Ornamentation - Rear Door Trim Panel Finish Panel
Removal and Installation
Removal
Installation



1. Remove interior door handle escutcheon.
Remove cover from door ha ndle escutcheon securing
screw and slacken and remove screw.
Pull door handle inwards and exercising care to avoid
damaging tweeter, remove escutcheon from casing.

2. Remove veneer panel from casing.
1. Using a thin plastic leve r, carefully ease rear of
veneer panel inwards to release the two rear
securing tangs.
2. Slide veneer panel re arwards to release front
retainers.
1. Position veneer panel on casing and slide forward to engage
front retainers.
2. Using a soft pad or cloth, press re ar of panel firmly to seat the
securing tangs.
3. Position door handle escutche on on casing, fit and tighten
securing screw and fit cover over screw.

Interior Trim and Ornamentation - Rear Door Trim Panel
Removal and Installation
Removal

1. Remove interior door handle escutcheon.
1. Remove cover from door handle escutcheon securing screw and slac ken and remove screw.
2. Pull door handle inwards and exercising care to avoid damaging tweeter, remove escutcheon from
casing.
2. Remove door casing veneer panel. Refer to 76.47.12.

3. Slacken and remove the armres t centre securing screw.

4. Carefully release the six fastener s (seven on long wheelbase)
securing lower section of casing to door.
5. Lift rear edge of door casing to release retaining clip housing
from door panel.

6. Lift casing clear of door wais t flange and lock button and
withdraw for access.

7. Disconnect speaker, puddle lamp and switchpack harness
multiplugs.
8. Remove armrest lower securing clip housing from casing. and
refit to door.

9. Remove door inner waist seal from holder.
Slacken and remove screws securing waist seal holder
and remove seal holder.
10. Remove armrest from casing. Refer to 76.34.23.
11. Slacken and remove puddle la mp securing screws and
remove lamp assembly from casing.

Installation


12. Remove pocket from door casing.
1. Release puddle lamp harness from clips at base of door pocket.
2. Slacken and remove th e two screws securing
bottom of pocket to casing.
3. Remove two spring clips securing top of pocket to casing.
13. Lift pocket from casing

14. Slacken and remove door sp eaker securing screws and
remove speaker from casing.
15. Remove speakere grill from casing
16. Remove casing to to door securing clips.
1. Fit and fully seat casing securing clips.
2. Position speaker grill in casing align speaker and fit and tighten
securing screws.
3. Position pocket in casing and secure with screws and spring
clips.
4. Fit puddle lamp to casing, fit and tighten securing screws and
position harness in pocket clips.
5. Fit door armrest to casing. Refer to 76.34.23.
6. Fit inner waist seal holder to casing and fit and tighten the six
securing screws.
7. CAUTION: Before installing door casing, ensure that

primary water shedder is undamag
ed and correctly attached to
door inner panel.
Align and fit inner waist seal.
8. Check that armrest tang locater and screw insert are correctly
positioned in door panel.
9. Position casing for access and connect speaker, puddle lamp
and switchpack harnesses.
10. Finally position casing locating fold over waist flange and
firmly press armrest to locate retaining tang in door panel.
11. Commencing at front , press and firmly seat casing lower
fasteners in door inserts
12. Fit and tighten armrest centre se curing screw in door insert.
13. Fit door veneer panel. Refer to 76.47.12.
14. Position door handle escutche on on casing, fit and tighten
securing screw and fit cover over screw.

Interior Trim and Ornamentation - Rear Window Blind
Removal and Installation
Removal
Installation

1.
Remove rear seat cushion. Refer to 76.73.18.
2. Remove rear seat squa b. Refer to 76.70.38.
3. Remove rear parcel tray. Refer to 76.67.06.90
4. Place parcel tray face down on clean bench.

5. Remove sunblind assembly.
Slacken and remove nuts securing sunblind to parcel tray.
Remove washers.
Remove sunblind from parcel tray.
Repeat procedure to remove opposite side sunblind.
1. Position sunblind on parcel tray.
2. Install washers on sunblind studs.
3. Install nuts on sunblind stud s and tighten nuts to 5-7Nm.
4. Repeat above procedure to inst all opposite side sunblind.
5. Install parcel tray/sunblind as sembly. Refer to 76.67.06.90.
6. Install rear seat squa b. Refer to 76.70.38.
7. Install rear seat cushio n. Refer to 76.73.18.