JAGUAR XFR 2010 1.G Workshop Manual

Published: 11-May-2011
Rear Drive Axle/Differential - Differential Case TDV6 3.0L Diesel /V8 5.0L
Petrol/V8 S/C 5.0L Petrol
Removal and Installation


Removal

All vehicles

1. WARNING: Do not work on or under a vehicle supported only by a
jack. Always support the vehicle on safety stands.

Raise and support the vehicle.

2. Refer to: Rear Halfshaft - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-05 Rear Drive Halfshafts, Removal and Installation).
3. Refer to: Exhaust System (309-00C Exhaust System - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and Installation).

4. CAUTIONS:


Do not use the 5mm hole on the differential case
flange for the alignment mark.


Make sure that the driveshaft is supported with
suitable retaining straps.


NOTE: Using the 3mm hole on the differential case
flange, paint an alignment mark (as indicated) to aid
correct installation of the driveshaft to the differential case. 205-932
Remover, Driveshaft Special Tool(s)

5. NOTES:


On vehicles with diesel engine, note the illustrated
orientation of the special tool.


Make sure that the special tool is correctly installed to
the recess on the driveshaft.
Special Tool(s): 205-932

























6. CAUTION: Care must be taken not to damage the
surrounding components when using the special tool.


NOTE: Using a suitable hammer and drift, make sure
that you only hit the corner edges of the special tool to
remove the driveshaft.
Special Tool(s): 205-932 www.JagDocs.com

M12 90 Nm

Vehicles with supercharger

2.
All vehicles


3. NOTE: Make sure that the alignment mark on the driveshaft
is correctly aligned to the alignment mark on the
differential case.
Torque: 75 Nm



















4. NOTES:


This step only applies if a new driveshaft is being
installed.


Using the 3mm hole on the differential case flange
and paint alignment mark on the driveshaft (as indicated).
Make sure that the alignment marks are correctly aligned.
Torque: 75 Nm

S/C 5.0L Petrol, Removal and Installation).

6. Refer to: Rear Halfshaft - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-05 Rear Drive Halfshafts, Removal and Installation).
7. Check and top-up the differential case.

Torque: 30 Nm

Published: 11-May-2011
Rear Drive Axle/Differential - Differential Front Bushing TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol
Removal and Installation

Special Tool(s)


204-274
Bush install and removal tool

204-275
Bush install and removal tool

204-335
Bush install and removal tool

204-601
Bush install tool

303-1121
Installer, Crankshaft Seal Removal


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

2. Refer to: Differential Case - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-02 Rear Drive Axle/Differential, Removal and Installation).

Installation
3. Special Tool(s): 204-335

1. NOTE: Make sure the new bushes are installed in the correct
orientation.
.

Special Tool(s): 204-275, 204-601, 303-1121, 204-274



2. Refer to: Differential Case - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-02 Rear Drive Axle/Differential, Removal and Installation). www.JagDocs.com

204-265
Remover/Installer, Drive Pinion Seal

204-266
Adapter for 204-265

204-267
Adapter for 204-265

204-269
Flange remover forcing screw

205-053
Retainer, Drive Flange

Removal


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

2. Refer to: Driveshaft - TD4 2.2L Diesel (205-01, Removal and
Installation).
Refer to: Driveshaft - V6 3.0L Petrol (205-01 Driveshaft, Removal and Installation).
Refer to: Driveshaft - V8 5.0L Petrol/V8 S/C 5.0L Petrol (205-01 Driveshaft, Removal and Installation).
Refer to: Driveshaft - TDV6 3.0L Diesel (205-01 Driveshaft, Removal and Installation).


3. NOTE: Measure for installation.
Measure the depth of the pinion nut on the pinion shaft. 205-053-03
Adapter, Drive Pinion Flange