sensor JAGUAR XJ6 1994 2.G Manual PDF

Security System - RESTRICTED ISSUE 84
-
A5.9.8 Intrusion sensors
1. Check harness wiring continuity as shown below:
SLCM connector Sensor connector Function
Lsft-hand side sensor
pin 10 pin 2 ground
pin
11 pin 4 40kHz
pin 12 pin 5 I/P
pin 13 pin 3 +av
RightAand side sensor
pin 2 pin 2 ground
pin
3 pin 4 40kHz
pin 4 pin 1 I/P
pin 5 pin 3 +av
2. Lock and arm the vehicle while sat inside; wait 15 seconds, then attempt to cover either sensor rea
with the palm
of the hand. Check that sensor detects movement and activates alarm. Repeat test
for second sensor.
+8v P13B
40KHz P11 B
IPP128
rPloB
1
Fig. 1 Intrusion Sensor Circuit J86- 1013
Issue 1 August 1994 32 X300 VSM

Security System - RESTRICTED ISSUE 84
-
AS. 10 INCLINATION SENSOR - RENEW
SRO 86.52.21
. Remove the trunk floor carpet.
. Remove the trunk front liner.
. Remove the trunk seal retainer. See SRO 76.19.44, Section
. Remove the trunk side liner.
. Disconnect the inclination sensor multiplug. (1 Fig. 1).
. Undo and remove the sensor mounting bracket securing
nuts
(2 Fig. 1). Remove the sensor (3 Fig. 1) complete with
mounting bracket (4 Fig. 1).
. Displace the mounting bracket retaining tang and remove
the sensor.
. Fitting a new inclination sensor is the reverse of the re- moval procedure.
13.
AS. 11
SRO 86.52.01
. Open
the trunk and remove the battery cover.
. Disconnect the battery ground lead.
. Remove the trunk floor carpet.
9 Remove the trunk front liner.
Remove the trunk seal retainer. See SRO 76.19.44, Section
. Remove the trunk side liner.
. Undo and remove the inclination sensor securing nuts (2 Fig. 1) and displace the sensor (3 Fig. 1) to gain access to
the SLCM (1 Fig. 2).
SECURIN & L OCKlNG CONTROL MODULE
(SLCM)
- RENEW
13.
. Undo and remove the SLCM securing nuts (5 Fig. 1).
. Displace the SLCM. Identify the SLCM multi-plugs (2 Fig. 2) for subsequent reconnection. Disconnect the mult- plugs and remove the SLCM.
9 Fitting a new SLCM is the reverse of the removal pro- cedure. Makesure thatthe multi-plugs are reconnected as
removed from the old SLCM.
The
arrowson Fig. 2 showthe position ofthe mount- ing bolts and mounting holes. U:
3
I 1 J86 1882
Fig. 1
Fig.
2
Issue 1 August 1994 40 X300 VSM

Security System - RiESTRICTED ISSUE
AS. 12 INTRUSION SENSOR - RENEW
SRO
86.52.20
. Carefully displace the intrusion sensor from the headlin- ing.
W: View 1 (Fig. 1) shows a vehicle fitted with a sliding
roof. View 2 (Fig. 1) shows a vehicle without a sliding
roof.
. Disconnect the multi-plug and remove the intrusion sen-
Reconnect multi-plug to a new intrusion sensor.
. Locate the intrusion sensor securing studs and carefully
push into the headlining. Make sure the intrusion sensor
is fully seated.
sor.
A5.13
HAND
TRANSMITTER BATTERY - RENEW
SRO 86.52.28
Remove batteries (2 Fig. 2) and discard.
Fit two new batteries making sure the polarity is as shown
Fit and fully seat the transmitter rear cover.
rn Remove the hand transmitter rear cover (1 Fig. 2).
in Fig 2.
AS. 14
SRO 86.52.08
VAL El S WITCI - RENM
J86-I550
Fig. 1
I
I Fig. 2
Open the centre console compartment and carefully dis-
. Disconnect the harness connector and remove the valet
Fitting a new valet switch is the reverse of the removal pro-
place the valet switch.
switch.
cedure. Make sure the switch is fully seated.
Fig.
3
X300 VSM 41 Issue 1 August 1994