ECU LAND ROVER DISCOVERY 1995 Workshop Manual

44AUTOMATIC GEARBOX
12
REPAIR Oil seal replacement
14.Remove circlips and springs from control unit.
Note locations of long and short springs.
15.Using seal replacer/remover LST113 remove
and discard seals.
16.Clean control unit, springs and circlips and check
that they are satisfactory for further use.
17.Fit new seals to control unit using LST113,
ensure seals are fully seated.
18.Fit springs to locations noted during removal and
secure with circlips.
Refit
19.Fit control unit to gearbox, locating throttle valve
behind cam and engaging selector quadrant with
manual valve.
20.Loosely fit securing screws.21.Manually open throttle linkage to full throttle
position.
22.Engage special tool LST 109 between control
unit and throttle valve pin.
23.Set correct distance between control unit and
cam.
24.Remove special tool and close throttle.
25.Fit new 'O' ring seals to oil screen using light
grease to aid assembly.
26.Fit oil screen and suction pipe with spacer and
secure with three bolts.
27.Refit oil pan using a new gasket.
28.Connect dipstick tube to oil sump and tighten
bolt at bell housing.
29.Refit chassis cross member.
30.Refit catalytic converter assembly
31.Connect electrics to Lambda sensors.
32.Connect heat shield front pipe to manifold.
33.Connect battery.
34.Refill gearbox oil system using correct grade of
oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids

ZF
13
REPAIR KICKDOWN CABLE
Service repair no - 44.15.01
Remove
1.Site vehicle on a four post ramp [hoist].
2.Select neutral 'N' gear lever.
3.Disconnect battery negative lead.
4.Disconnect kickdown cable at throttle linkage.
5.Release outer cable locknut.
6.Disconnect cable from mounting bracket.
7.Release cable from bracket attached to cylinder
head.
8.Feed cable through to underside of vehicle.
9.Raise vehicle on ramp [hoist].
10.Drain oil and refit plug with new seal.
11.Detach heat shield at front exhaust pipe to
manifold.
12.Disconnect electrics from Lambda sensors.
13.Remove catalytic converter assembly.
14.Remove chassis cross-member from under
gearbox.
15.Disconnect dipstick tube at oil sump. Loosen
securing bolt at bell housing and move dipstick
aside.
16.Remove clamps securing oil sump. Note their
locations for refit, and withdraw sump.
17.Pull kickdown inner cable to fully open valve
cam. Wedge cam in this position.
18.Release cable from cam by pushing inner cable
into outer casing and detaching cable nipple
from cam.
19.Using special tool LST112 compress cable tangs
and remove cable from gearbox.
20.If cable is to be refitted remove 'O' ring seal and
clean cable assembly.
Refit
21.Fit new 'O' ring seal to cable and lubricate seal.
22.Fit cable to gearbox casing ensuring it is
correctly seated.
23.Fit inner cable nipple to its location on cam.
NOTE: When a new cable is fitted, to help
locate nipple to cam, introduce a curve
into the cable. Do not bend or kink cable.24.Remove wedge from cam and ensure nipple
remains engaged.
25.Feed free end of cable assembly into engine
compartment.
26.Refit oil pan using a new gasket.
27.Connect dipstick tube to oil sump and tighten
bolt at bell housing.
28.Refit chassis cross-member
29.Refit catalytic converter assembly
30.Connect electrics to Lambda sensors.
31.Connect heat shield front pipe to manifold.
32.Lower vehicle on ramp [hoist].
33.Fit cable to bracket at cylinder head.
34.Locate cable in mounting bracket, do not tighten
locknut.
35.Fit cable to throttle linkage.
36.Ensure throttle linkage is fully closed.
37.Adjust outer cable to achieve a gap of 0,25 to
1,25mm (dimension 'A') between end of outer
cable and crimped collar on inner cable.
38.Tighten locknuts and recheck gap.
NOTE: If fitting a new cable, and collar on
inner cable is loose, measure distance 'B'
on old cable. Crimp collar on new cable to
this dimension.
39.Reconnect battery negative lead.
40.Refill gearbox oil using correct grade of oil.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids

44AUTOMATIC GEARBOX
14
REPAIR EXTENSION HOUSING
Service repair no - 44.20.18
Remove
1.Remove transfer gearbox.
See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
2.Drain oil from automatic gearbox.
3.Remove bolts securing left hand mounting
bracket to extension housing and withdraw
bracket.
4.Remove transfer gear lever housing securing
bolts and move housing aside.
5.Remove securing bolts and withdraw extension
housing from over coupling shaft. Remove and
discard gasket.
6.Place extension housing on bench and remove
oil seal.
7.Ensure that all surfaces are clean and housing is
free from damage. If damage is found and
housing has to be renewed remove dowels from
face of existing housing and fit to new housing.
8.Using special tool LST108 fit new oil seal to
housing.Refit
9.Fit extension housing to gearbox, with a new
gasket, ensuring oil seal is not damaged by
extension shaft.
10.Secure housing with nine bolts. Tighten to
23
Nm.
11.Refit transfer gear lever housing to top of
extension housing. Tighten to
25 Nm.
12.Refit mounting bracket to extension housing.
Tighten to
52 Nm.
13.Refit transfer gear box.See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
14.Refill automatic gearbox lubrication system with
correct grade of oil.
See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended Lubricants and Fluids

ZF
15
REPAIR GOVERNOR ASSEMBLY
Service repair no - 44.22.01
Remove
1.Remove transfer gearbox.
See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
2.Drain oil from automatic gearbox.
3.Remove bolts securing left hand mounting
bracket to extension housing and withdraw
bracket.
4.Remove transfer gear lever housing securing
bolts and move housing aside.
5.Remove extension housing ensuring seal is not
damaged, remove and discard gasket.
6.Remove extension shaft retaining bolt, withdraw
shaft and discard 'O' ring seal. If Tdi vehicle
remove spacer.
7.Remove governor assembly.
8.Remove park gear from governor assembly.
9.Detach governor housing.
10.Remove security clip and counter weight.
11.Remove and discard 'O' ring seal from output
shaft and three seal rings from 'F' clutch
housing.
12.Clean all components.
13.If necessary detach parking pawl by removing
guide plates and withdrawing mechanism.Refit
14.Refit parking pawl mechanism if removed.
15.Fit and lubricate new seal rings to 'F' clutch
housing shaft, ensure they are correctly seated.
16.Apply petroleum jelly to a new 'O' ring seal. Fit to
output shaft
17.Fit park gear to governor assembly tightening
screws to correct torque.
18.Fit governor assembly to output shaft.
19.Fit extension shaft with spacer if Tdi. Fit new 'O'
ring under bolt head.
20.Fit extension housing, avoid damaging seal.
Tighten to
23 Nm.
21.Refit transfer gear lever housing to extension
housing.
22.Refit mounting bracket to extension housing.
Tighten to
52 Nm.
23.Refit transfer gearbox.See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
24.Refill automatic gearbox with correct grade of oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids

44AUTOMATIC GEARBOX
16
REPAIR GOVERNOR HUB
Service repair no - 44.22.04
Remove
1.Remove transfer box.
See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
2.Remove transfer gear selector housing.
3.Loosen nine bolts holding extension housing.
4.Remove extension housing ensuring that seal is
not damaged, discard gasket.
5.Remove extension shaft and retaining bolt with
'O' ring. If Tdi vehicle remove spacer.
6.Remove governor assembly with parking wheel.
7.Remove two screws holding governor housing.
8.Remove two bolts, remove parking wheel.
Discard governor hub.
9.Remove security clip and counter-weight.
10.Remove 'O' ring from output shaft and discard.
11.Remove three seal rings from 'F' clutch housing
shaft.
12.Inspect all parts for damage or wear, replace if
necessary.
Refit
13.Fit counterweight and security clip into new
governor hub.14.Secure governor housing to governor hub.
Tighten to
10Nm.
15.Fit parking wheel to governor hub. Tighten to10
Nm.
16.Fit three new seal rings onto F clutch housing
shaft, fit 'O' ring onto output shaft.
NOTE: To aid fitting of 'O' ring apply
petroleum jelly.
17.Push governor assembly and parking wheel onto
output shaft until seated.
NOTE: Apply petroleum jelly to 'O' ring.
Ensure seal rings are snapped together
and seated.
18.Fit new gasket to rear of gearbox. Fit extension
housing, avoid damaging seal.
19.Fit extension shaft,and spacer if Tdi, apply
Loctite 270 to retaining bolt. Using a new 'O'
ring, tighten bolt to
42 Nm.
20.Tighten nine extension housing nine bolts to23
Nm.
21.Fit transfer gear selector housing, tighten three
bolts to
25 Nm.
22.Refit transfer box.

ZF
21
REPAIR REPLACING PUMP
Service repair no - 44.32.01
1.Remove gearbox and transfer box assembly.
See LT230T Transfer Gearbox
2.Place gearbox on bench. Remove torque
converter using torque converter handles
18G1501, taking care not to damage torque
converter/oil pump housing oil seal.
3.Remove twelve bolts (inner ring pattern).
4.Remove bell housing and pump assembly from
gearbox case, discard gasket.
5.Remove eight bolts on rear of pump.
6.Screw in two bolts,diagonally opposite each
other, tap lightly using a soft headed mallet to
free pump assembly from intermediate plate.
7.Fit new pump assembly, aligning dowel with hole
in intermediate plate, press pump housing home.
8.Secure pump housing to intermediate plate
using eight hexagonal bolts. Tighten to
10 Nm.
9.Place bell housing and intermediate plate
assembly on bench, front face up. Using oil
pump rotation sleeve LST111, check that pump
gears rotate freely.
10.Before replacing intermediate plate/bell housing
assembly check that thrust washer and axial
cage are seated on A clutch housing.
11.Place new gasket and disc washer onto bell
housing and intermediate plate assembly using
a Petroleum Jelly.
12.Fit bell housing and intermediate plate assembly,
tighten twelve bolts to
46 Nm.

ZF
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Coupling shaft to mainshaft 42*......................................................................
Filler tube to sump 68.....................................................................................
Gear change lever to gearbox 25...................................................................
Cooler pipe adaptor to gearbox 42.................................................................
Securing screws - clutch F 10.........................................................................
Securing screw - parking pawl 10...................................................................
Securing screws - pump 10............................................................................
Intermediate plate plugs (M20) 50..................................................................
Intermediate plate plugs (M14) 40..................................................................
Bell housing mounting bolts 46.......................................................................
Governor mounting screws 10........................................................................
Extension housing bolts 23.............................................................................
Control unit mounting bolts 8.........................................................................
Sump plug 10..................................................................................................
Mounting screws for sump 8..........................................................................
Drive plate to converter 39*.............................................................................
Gearbox to engine 42.....................................................................................
Strut (threaded end) 42...................................................................................
Bottom cover to converter housing 9.............................................................
Cover - converter housing 9...........................................................................
Drive plates to crankshaft adaptor 40*............................................................
Adaptor to crankshaft 84.................................................................................
NOTE: * These bolts must have threads coated with Loctite 270 prior to assembly.
Torque values below are for all screws and bolts used except for those that are specified otherwise.
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................

ZF
1
SERVICE TOOLS AUTOMATIC GEARBOX HOLDING FIXTURE
NOTE: This fixture enables ZF gearbox to be held securely during bench sited repairs. It can be
manufactured to details given, or purchased under service tool number LST 118.

47PROPELLER SHAFTS
4
REPAIR REAR PROPELLER SHAFT
Service repair no - 47.15.03
NOTE: SGF rubber coupling should be left
attached to propeller shaft. Only remove
coupling from propeller shaft if
replacement is required.
Remove
1.Scribe alignment marks on flanges at both ends
of propeller shaft to ensure correct refitting.
2.Remove three nuts and bolts securing flexible
coupling to axle flange.
3.Remove nuts securing propeller shaft flange to
transfer gearbox.
4.Raise propeller shaft at gearbox end detach
coupling from spigot at differential and withdraw
shaft.
NOTE: For replacement of spigot (pinion
flange centralising peg).
See REAR AXLE
AND FINAL DRIVE, Overhaul, Axle
Differential Assembly
Overhaul
Service repair no - 47.15.12
NOTE: Refer to front propeller shaft
overhaul procedure for gearbox end of
shaft. The SGF rubber coupling is a
non-serviceable item.
Refit
5.Locate flexible coupling over spigot, align
scribed marks and secure at transfer gearbox.
Tighten to
47 Nm.
6.Secure flexible coupling to axle flange with three
nuts and bolts and Tighten to
78 Nm.
FLEXIBLE COUPLING
NOTE: Flexible coupling should only be
removed if a new coupling is to be fitted.
Remove
1.Remove rear propeller shaft.
See Rear
Propeller Shaft.
2.Remove nuts and bolts securing flexible
coupling to propeller shaft.
Refit
3.Reverse removal procedure. Fit nuts and bolts.
Tighten to
78 Nm.

REAR AXLE AND FINAL DRIVE
3
REPAIR REAR HUB ASSEMBLY
Service repair no - 64.15.01
Remove
1.Place rear axle onto axle stands and remove
road wheel.
2.Release brake hose clips and remove brake
caliper bolts. Secure to one side.
WARNING: Take care not to kink brake
hose.
3.Remove five bolts and withdraw axle shaft.
4.Remove joint washer.
5.Bend back lock washer tabs.
6.Remove locknut and lock washer.
7.Remove hub adjusting nut.
8.Remove spacing washer.
9.Remove hub and brake disc assembly complete
with bearings.REAR HUB COMPONENTS
1. Sensor ring retaining nut ABS.
2. Axle shaft.
3. Axle shaft joint washer.
4. Axle shaft retaining bolt (five off).
5. Lock nut.
6. Lock washer.
7. Hub adjusting nut.
8. Spacing washer.
9. Outer bearing.
10. Hub.
11. Inner bearing.
12. Grease seal.
13. Brake disc.
14. Disc retaining bolt (five off).
15. Sensor ring ABS.