LEXUS LS600H 2017 Owners Manual

5817-2. Steps to take in an emergency
7
When trouble arises
LS600h/LS600hL_EE(OM50G20E)
*: Use of the jack (P. 571)
Location of the emergency tire puncture repair kit, jack and tools
Wheel nut wrench
Jack handle
Parking brake release tool
Towing eyelet
Jack*
Screwdriver
Tools
Emergency tire puncture repair
kit
1
2
3
4
5
6
7
8

5827-2. Steps to take in an emergency
LS600h/LS600hL_EE(OM50G20E)
■Bottle
■Compressor
Emergency tire puncture repair kit components
Hose
Air release cap
Stickers
1
2
3
Compressor switch
Air pressure gauge
Power plug
1
2
3

5837-2. Steps to take in an emergency
7
When trouble arises
LS600h/LS600hL_EE(OM50G20E)
Lift up the handle and fold the trunk floor back. (P. 443)
Remove the tool tray cover.
Take out the emergency tire
puncture repair kit.
Taking out the emergency tire puncture repair kit
1
2
3

5847-2. Steps to take in an emergency
LS600h/LS600hL_EE(OM50G20E)
Lift up the handle and fold the trunk floor back. (P. 443)
Remove the tool tray cover.
Remove the jack after removing
the hook.
Taking out the jack
1
2
3

5857-2. Steps to take in an emergency
7
When trouble arises
LS600h/LS600hL_EE(OM50G20E)
Remove the valve cap from the
valve of the punctured tire.
Extend the hose. Remove the air
release cap from the hose.
You will use the air release cap again.
Therefore keep it in a safe place.
Connect the hose to the valve.
Screw the end of the hose clockwise
as far as possible.
Make sure that the compressor
switch is off.
Emergency repair method
1
2
3
4

5867-2. Steps to take in an emergency
LS600h/LS600hL_EE(OM50G20E)
Lift the rubber stopper on the
compressor.
Remove the power plug from the
compressor.
Connect the power plug to the power outlet socket. ( P. 451)
Connect the bottle to the com-
pressor.
Make sure that the bottle is securely
connected.
5
6
7
8

5877-2. Steps to take in an emergency
7
When trouble arises
LS600h/LS600hL_EE(OM50G20E)
Attach the 2 stickers as shown.
Remove any dirt and moisture from
the wheel before attaching the label. If
it is impossible to attach the label,
make sure to tell any authorized Lexus
dealer or repairer, or another duly
qualified and equipped professional
when you have them repair and
replace the tire that sealant is injected.
Check the specified tire inflation
pressure.
Tire inflation pressure is specified on
the label as shown. ( P. 630)
Start the hybrid system. (P. 247)
To inject the sealant and inflate
the tire, turn the compressor
switch on.
9
10
11
12

5887-2. Steps to take in an emergency
LS600h/LS600hL_EE(OM50G20E)
Inflate the tire until the recom-
mended pressure is reached.
The sealant will be injected and
the pressure will spike to 300
kPa (3.0 kgf/cm2 or bar, 44
psi) or 400 kPa (4.0 kgf/cm2
or bar, 58 psi), then gradually
decrease.
The air pressure gauge will dis-
play the actual tire inflation
pressure about 1 minute (15
minutes at low temperature)
after the switch is turned on.
• Turn the compressor switch off
and then check the tire inflation
pressure. Being careful not to
over inflate, check and repeat
the inflation procedure until the
recommended tire inflation
pressure is reached.
• If the tire inflation pressure is still
lower than the recommended
level after inflation for 10 min-
utes (35 minutes at low tem-
perature) with the switch on, the
tire is too damaged to be
repaired. Turn the compressor
switch off and contact any
authorized Lexus dealer or
repairer, or anot her duly quali-
fied and equipped professional.
• If the tire inflation pressure
exceeds the recommended
level, let out some air to adjust
the tire inflation pressure.
( P. 592, 630)
13
1
2

5897-2. Steps to take in an emergency
7
When trouble arises
LS600h/LS600hL_EE(OM50G20E)
With the compressor switch off, disconnect the hose from the valve on
the tire and then pull out the power plug from the power outlet socket.
Some sealant may leak when the hose is removed.
Install the valve cap onto the valve of the emergency repaired tire.
Attach the air release cap to the
end of the hose.
If the air release cap is not attached,
the sealant may leak and the vehicle
may get dirty.
Temporarily store the bottle in the trunk while it is connected to the
compressor.
To spread the liquid sealant evenly within the tire, immediately drive
safely for about 5 km (3 miles) below 80 km/h (50 mph).
After driving, stop your vehicle in
a safe place on a hard, flat surface
and reconnect the compressor.
14
15
16
17
18
19

5907-2. Steps to take in an emergency
LS600h/LS600hL_EE(OM50G20E)
Turn the compressor switch on
and wait for several seconds, then
turn it off. Check the tire inflation
pressure.
If the tire inflation pressure is
below 130 kPa (1.3 kgf/cm
2 or
bar, 19 psi): The puncture can-
not be repaired. Contact any
authorized Lexus dealer or
repairer, or another duly quali-
fied and equipped profes-
sional.
If the tire inflation pressure is
between 130 kPa (1.3 kgf/cm
2
or bar, 19 psi) and a point
below the recommended level:
The tire can be repaired. Pro-
ceed to step .
If the tire inflation pressure is at
the recommended level: Pro-
ceed to step .
Turn the compressor switch on to inflate the tire until the recommended
tire inflation pressure is reached. Drive for about 5 km (3 miles) and
then perform step .
Attach the air release cap to the
end of the hose.
If the air release cap is not attached,
the sealant may leak and the vehicle
may get dirty.
20
1
2
21
3
22
21
19
22