MAZDA MODEL 626 2002 Owners Manual

8-15
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
5. Fill the radiator (to the top of the filler neck) and then the coolant reservoir (to
F) with as much ethylene-glycol-based
coolant and water as necessary to
provide protection from freezing and
corrosion.
In extremely cold climates, add the
amount recommended by the coolant
manufacturer.
6. Reinstall the cooling system cap.
7. Run the engine at idle for about 10 minutes.
8. Then do this: •Run the engine at 2,500 rpm for
about 5 minutes.
• Increase the engine speed to 3,000
rpm for about 5 seconds and then
release the accelerator.
• Do this 4 or 5 times.
• Make sure the engine temperature
gauge does not reach the HOT zone.
After turning off the engine, inspect the
drain plug and the water hoses for leaks.
9. After the engine has cooled, remove the cooling system cap and inspect the
coolant level. If it ’s low, repeat steps 5
to 8.
Because this procedure requires technical
expertise, we recommend that it be done
by an Authorized Mazda Dealer.





Inspecting Brake/Clutch Fluid
Level
The brakes and clutch draw fluid from the
same reservoir.
Inspect the fluid level in the reservoir
regularly. It should be kept at MAX.
The level normally drops with
accumulated distance, a condition
associated with wear of brake and clutch
linings. If it is excessively low, have the
brake/clutch system inspected by an
Authorized Mazda Dealer.
NOTE
Mixing green coolant with orange
coolant could decrease the service life
expectancy of the coolant. Use only
genuine Mazda orange colored or
equivalent coolant.
Brake/Clutch Fluid
J94S.book Page 15 Saturday, June 23, 2001 1:04 PM

8-16
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Adding Brake/Clutch Fluid
If the fluid level is low, add fluid until it
reaches MAX.
Before adding fluid, thoroughly clean the
area around the cap.
Spilled Brake Fluid:Spilled brake fluid is dangerous. If it
gets in your eyes, they could be
seriously injured. If this happens,
immediately flush your eyes with
water and get medical attention.
Brake fluid spilled on a hot engine
could cause a fire. Be careful not to
spill brake fluid on yourself or on the
engine.
Low Brake/Clutch Fluid Levels:
Low brake/clutch fluid levels are
dangerous. Low levels could signal
brake lining wear or a brake system
leak. Your brakes could fail and cause
an accident. If you find a low fluid
level, have the brakes and clutch
inspected.
WARNING• Brake and clutch fluid will damage
painted surfaces. If brake or clutch
fluid does get on a painted surface,
wipe it off immediately.
• Using nonspecified brake and clutch
fluids (page 10-4) will damage the
systems. Mixing different fluids
will also damage them.
If the brake/clutch system
frequently requires new fluid,
consult an Authorized Mazda
Dealer.
CAUTION
J94S.book Page 16 Saturday, June 23, 2001 1:04 PM

8-17
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Inspecting Power Steering Fluid
Level
Inspect the fluid level at each engine oil
change. Add fluid if necessary; it does not
require periodic changing.
The level must be kept between the HIGH
and LOW marks.
Visually examine the lines and hoses for
leaks and damage.
1. Park on a level surface, well off the
right-of-way, and set the parking brake
firmly.
2. Turn off the engine and allow it to cool. 3. Remove the filler cap and attached
dipstick.
4. Wipe them clean and put them back.
5. Remove again and inspect the level.
6. It must be between HIGH and LOW. Add fluid if necessary.
Don ’t overfill.
If new fluid is required frequently, consult
an Authorized Mazda Dealer.
Power Steering Fluid
To avoid damage to the power steering
pump, don’ t operate the vehicle for
long periods when the power steering
fluid level is low.
NOTE
Use specified power steering fluid
(page 10-4).
CAUTION
High
Low OK
J94S.book Page 17 Saturday, June 23, 2001 1:04 PM

8-18
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Inspecting Automatic transaxle
Fluid Level
The automatic transaxle fluid level should
be inspected regularly. Measure it as
described below.
The volume of fluid changes with the
temperature. Fluid must be checked at idle
without driving at normal operating
temperature.
1. Park on a level surface and set the
parking brake firmly.
2. Idle the engine about two minutes. Push down on the brake pedal.
3. Move the shift lever through all ranges and set it at P. 4. With the engine still idling, pull out the
dipstick, wipe it clean, and put it back.
5. Pull it out again. The proper fluid level is marked on the
dipstick as follows.
2.0-liter engine
Scale A
When the engine has been running and the
fluid is at normal operating temperature,
about 65 °C (150 °F) to 77 °C (170 °F), the
level must be within the crosshatched area
on the dipstick.
Automatic Transaxle Fluid
(ATF)
• Low fluid level causes transaxle
slippage. Overfilling can cause
foaming, loss of fluid, and transaxle
malfunction.
• Use specified fluid (page 10-4). A
nonspecified fluid could result in
transaxle malfunction and failure.
CAUTION
Sudden Vehicle Movement:Shifting the shift lever without first
depressing the brake pedal is
dangerous. The vehicle could move
suddenly and cause an accident.
Make sure the brake pedal is applied
before shifting the shift lever.
WARNING
A
B
J94S.book Page 18 Saturday, June 23, 2001 1:04 PM

8-19
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Scale B
When the engine has not been running,
and the outside temperature is above 10°C
(50 °F), the level should be between the
bottom hole on the dipstick and the
bottom of the crosshatched area on the
dipstick.
Fully insert the dipstick. When adding
fluid, make sure the fluid level doesn ’t
pass the crosshatched area on the dipstick. 2.5-liter engine
Fluid hot scale A
When the vehicle has been driven and the
fluid is at normal operating temperature,
about 65
°C (150 °F), the level must be
between Full and Low.
Fluid cold scale B
When the engine has not been running
and the outside temperature is about 20 °C
(70 °F), the level must be between Full and
Low.
•
Use scale B only as a reference.
• If outside temperature is lower than
about 10 °C (50 °F), start the engine
and inspect the fluid level after the
engine reaches operating
temperature.
• If the vehicle has been driven for an
extended period at high speeds or in
city traffic in hot weather, inspect
the level only after stopping the
engine and allowing the fluid to
cool for 30 minutes.
NOTE
Inspect both sides of the dipstick for
accurate reading.
CAUTION
•Use the cold scale only as a
reference.
• If outside temperature is lower than
about 20 °C (70 °F), start the engine
and inspect the fluid level after the
engine reaches operating
temperature.
• If the vehicle has been driven for an
extended period at high speeds or in
city traffic in hot weather, inspect
the level only after stopping the
engine and allowing the fluid to
cool for 30 minutes.
A
B
CAUTION
J94S.book Page 19 Saturday, June 23, 2001 1:04 PM

8-20
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Fully insert the dipstick. When adding
fluid, inspect with the dipstick to make
sure it doesn’t pass full.





Inspecting Washer Fluid Level
Inspect fluid level in the washer fluid
reservoir; add fluid if necessary.
Use plain water if washer fluid is
unavailable.
But use only washer fluid in cold weather
to prevent it from freezing.
NOTE
Inspect both sides of the dipstick for
accurate reading.
Wa s h e r F l u i d
Substitute Washer Fluid:Using radiator antifreeze as washer
fluid is dangerous. If sprayed on the
windshield, it will dirty the
windshield, affect your visibility, and
could result in an accident. Use only
windshield washer fluid or plain
water in the reservoir.
WARNING
J94S.book Page 20 Saturday, June 23, 2001 1:04 PM

8-21
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the engine hood’s secondary
latch keeps the hood from opening when
the primary latch is released. A viscous paper air filter fits inside the air
cleaner housing, as shown. It
’s been
specially treated and should not be
cleaned and reused. Replace it when
necessary.





Replacing the Air Filter
1. Unfasten the clamps.
Body LubricationAir Filter
Don ’t drive without an air filter. This
could result in excessive engine wear.
NOTE
If the vehicle is operated in very dusty
or sandy areas, replace the filter more
often than recommended intervals.
CAUTION
Clamp
J94S.book Page 21 Saturday, June 23, 2001 1:04 PM

8-22
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
2. Lift off the air filter cover and remove the filter.
3. Wipe inside the air cleaner housing with a damp cloth.
4. Replace the filter.
5. Install in the reverse order of removal.
Replace the filter according to Scheduled
Maintenance (page 8-3). Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.





Replacing Windshield Wiper
Blades
When the wipers no longer clean well, the
blades are probably worn or cracked.
Replace them.
Air filter cover
Air filter
Wiper Blades
Hot waxes applied by automatic car
washes have been known to affect the
cleanability of windows.
To prevent damage to the wiper blades,
don’t use gasoline, kerosene, paint
thinner, or other solvents on or near
them.
To prevent damage to the wiper arms
and other components, don ’t move the
wipers by hand.
CAUTION
CAUTION
CAUTION
J94S.book Page 22 Saturday, June 23, 2001 1:04 PM

8-23
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
1. Raise the wiper arm and turn the blade assembly to expose the plastic locking
clip.
Compress the clip and slide the
assembly downward; then lift it off the
arm.
2. Hold the end of the rubber and pull until the tabs are free of the metal
support. 3. Remove the metal stiffeners from the
blade rubber and install them in new
blades.
To prevent damage to the windshield,
don’ t let the wiper arm fall on it.
Push
Plastic locking clip
CAUTION
Tabs pull out
Metal support
•
Don ’t bend the stiffeners. You need
to use them again.
• If the metal stiffeners are switched,
the blade’ s wiping efficiency could
be reduced.
So don’ t use the driver ’s side metal
stiffeners on the passenger ’s side, or
vice versa.
• Be sure to reinstall the metal
stiffeners in the new blade rubber so
that the curve is the same as it was
in the old blade rubber.
Stiffeners
CAUTION
J94S.book Page 23 Saturday, June 23, 2001 1:04 PM

8-24
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
4. Carefully insert the new blade rubber.Then install the blade assembly in the
reverse older of removal.
NOTE
Install the blade so that the tabs are
toward the bottom of the wiper arm.
Tabs
Battery
Battery-Related Lead Materials:Battery posts, terminals and related
accessories contain lead and lead
compounds, chemicals known to the
State of California to cause cancer
and reproductive harm.
Wash hands after handling.
Spilled Battery Fluid:
Spilled battery fluid is dangerous.
Battery fluid contains SULFURIC
ACID which could cause serious
injuries, if it gets in your eyes or on
your skin. If this happens,
immediately flush your eyes with
water for 15 minutes or wash your
skin thoroughly and get medical
attention. Be careful not to get battery
fluid on yourself.
Battery-Related Explosion:
Flames and sparks near open battery
cells are dangerous. Hydrogen gas,
produced during normal battery
operation, could ignite and cause the
battery to explode. An exploding
battery can cause serious burns and
injuries. Keep all flames, including
cigarettes, and sparks away from
open battery cells.
Children and Batteries:
Allowing children to play near
batteries is dangerous. Battery fluid
could cause serious injuries if it gets
in the eyes or on the skin. Always
keep batteries out of the reach of
children.
WARNING
J94S.book Page 24 Saturday, June 23, 2001 1:04 PM