MITSUBISHI MONTERO 2000 Service Repair Manual

GDI -Troubleshooting <A/T>13A-197
Inspection procedure 36
Purge control solenoid valve system
Probable cause
The engine-A/T-ECU controls the purge control solenoid valve in order to control
the purge air coming from the canister.DMalfunction of the purge control solenoid valve
DOpen circuit or short-circuited harness wire in the
purge control solenoid valve circuit
DMalfunction of the engine-A/T-ECU
OK
Check the trouble symptoms.NGCheck the harness wire between the
engine-A/T-ECU and the purge control
solenoid valve, and repair if necessary.
OK
Check the trouble symptoms.NGReplace the engine-A/T-ECU.
OK
Check the following connector:
D-120NG
Repair
OK
Measure at the engine-A/T-ECU con-
nector D-120.
DDisconnect the connector, and
measure at the harness side.
DVoltage between 5 and earth
(Ignition switch: ON)
OK:
System voltageNGCheck the following connector:
B-106NG
Repair
OK
Measure at the purge control solenoid
valve connector B-106.
DDisconnect the connector, and
measure at the harness side.
DVoltage between 2 and earth
(Ignition switch: ON)
OK:
System voltageNGCheck the harness wire between the
engine controlrelay and the purge
control solenoid valve, and repair if
necessary.
Check the purge control solenoid valve.
(Refer to GROUP 17 - On-vehicle Ser-
vice.)NG
Replace


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-198
DATA LIST REFERENCE TABLE
Caution
When shifting the select lever to D range, the brakes should be applied so that the vehicle does
not move forward.
NOTE
*1: Injector running time indicates the time where the power voltage is 11 V and the cranking speed
is 250 r/min or less. As the engine speed increases and the time passes by, the injector running
time decreases.
*2: There may be occasions of taking the injector running time approximately 10% longer than usual
when a vehicle has not been driven for a long time (mileage is no more than 500 km.)
*3: It is normal that the idle switch turns from ON to OFF when accelerator pedal position sensor (1st
channel) voltage increases by 200 - 600 mV from the idling position. Moreover, adjust the idle switch
and accelerator pedal position sesor if the idle switch keeps turning after the accelerator pedal is
depressed.
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
11Oxygen
sensorEngine: After having
warmed up
(Air/fuel mixture is
made leaner whenWhen at 4,000 r/min,
engine is deceler-
ated200 mV or lessCode No.
1113A-131
made leaner when
decelerating, and is
made richer when
racing.)
Race the engine sud-
denly.600 - 1,000 mV
Engine: After having
warmed up
(The oxygen sensor
signal is used to
check the air/fuelIdling
(after six minutes)400 mV or less
600 - 1,000 mV
(changes)
check the air/fuel
mixture ratio, and
control condition by
the engine-
A/T-ECU.)
2,500 r/min
12Air flow sen-DEngine coolantIdling22 - 48 HzCode No.13A-133
sortemperature: 80 -
95
_C
Lamps and all
2,500 r/min60 - 100 Hz
12
DLamps and all
accessories: OFF
DTransmission: P
range
RacingFrequency in-
creases in re-
sponse to racing
13Intake air
temperatureIgnition switch: ON or
with engine runningWhen intake air tem-
perature is - 20_
C-20_
CCode No.
1313A-135
sensor
When intake air tem-
perature is 0_
C0_
C
When intake air is
20_
C20_
C
When intake air is
40_
C40_
C


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-199
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
14Throttle
positionDEngine: After hav-
ing warmed upRelease the acceler-
ator pedal.4,000 mV or moreCode No.
1413A-137
sensor (2nd
channel)DIgnition switch: ON
(Engine: Stopped)
Depress the acceler-
ator pedal gradually.Voltage
decreases in
response to the
pedal depression.
Depress the acceler-
ator pedal fully.400 - 600 mV
16System
voltageIgnition switch: ONSystem voltageProcedure
No. 2513A-190
18Cranking
signal (igni-Ignition switch: ONEngine: StoppedOFFProcedure
No.2713A-191
signal (igni-
tion switch:
ST)
Engine: CrankingON
No.27
21Engine cool-
ant temper-
ature sensorIgnition switch: ON or
with engine runningWhen engine coolant
temperature is
-20_
C-20_
CCode No.
2113A-138
When engine coolant
temperature is 0_
C0_
C
When engine coolant
temperature is 20_
C20_
C
When engine coolant
temperature is 40_
C40_
C
22Crank angle
sensorDEngine: Cranking
DTachometer: Con-
nectedCompare the
tachometer with the
MUT-IIreading.IdenticalCode No.
2213A-140
DEngine: Idling
DIdle position
switch: ON
DWithin six minutesWhen engine coolant
temperature is
-20_
C1,250 - 1,450
r/min
DWithin six minutes
after engine
starting (Onlywhen
engine coolant
When engine coolant
temperature is 0_
C1,100 - 1,300
r/min
engine coolant
temperature is
80
_C)
When engine coolant
temperature is 20_
C1,000 - 1,200
r/min
When engine coolant
temperature is 40_
C900 - 1,100 r/min
When engine coolant
temperature is 80_
C550 - 650 r/min


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-200
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
25BarometricIgnition switch: ONAt altitude of 0 m101 kPaCode No.13A-145
pressure
sensor
At altitude of 600 m95 kPa
25
At altitude of 1,200 m88 kPa
At altitude of 1,800 m81 kPa
26Accelerator
pedal posi-Ignition switch: ON
(Depress and re-Release the acceler-
ator pedal.ONProcedure
No.2813A-192
tion switchlease the accelerator
pedal several times)
Depress the acceler-
ator pedal slightly.OFF
27Power
steering
fluid pres-
sure switchEngine: IdlingWhen steering wheel
is turnedONProcedure
No.3013A-194
28A/C switchEngine: Idling
(The A/C compres-A/C switch: OFFOFFProcedure
No.3113A-194
(The A/C compres-
sor is running when
the A/C switch is on.)
A/C switch: ONON
No.31
31Small lampEngine: IdlingLighting switch: OFFOFFProcedure13A-195
switch
Lighting switch: ONON
No.33
34Air flow sen-Engine: After havingIdlingONCode No.13A-133
sor reset
signalwarmed up
3,000 r/minOFF
12
37VolumetricDEngine coolantIdling20 - 40%--
efficiencytemperature: 85 -
95
_C
Lamps and all
2,500 r/min10 - 30%DLamps and all
accessories: OFF
DTransmission: P
range
Engine is suddenly
racedVolumetric effi-
ciency increases
in response to
racing
38Crank angle
sensorDEngine: Cranking (reading is possible at 2,000
r/min or less)
DTachometer: ConnectedEngine speeds
displayed on the
MUT-IIand
tachometer are
identical.--


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-201
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
41Injector
drive time*1D
Engine: CrankingWhen engine coolant
temperature is 0_
C120 - 160 msCode No.
4113A-147
When engine coolant
temperature is 20_
C70 - 90 ms
When engine coolant
temperature is 80_
C20 - 35 ms
Injector
drive time*2D
Engine coolant
temperature: 85 -
95_
CIdling0.3 - 0.8 ms
95_
C
D
Lamps and all
accessories: OFF
D
Transmission:
2,500 r/min0.4 - 1.0 ms
D
Transmission:
P range
D
Within six minutes
after engine start-
ing
When engine is sud-
denly racedIncreases
44Ignition ad-
vance valueD
Engine: After hav-
ing warmed up
D
Timing lamp is set.
(The timing lamp is
set in order toIdling12 - 28_
BTDCCode No.
4413A-148
set in order to
check actual igni-
tion timing.)
D
Within six minutes
after engine start-
ing
2,500 r/min15 - 35_
BTDC
49A/C relayEngine: After having
warmed up, idlingA/C switch: OFFOFF (compressor
clutch is not oper-
ating)Procedure
No.3113A-194
A/C switch: ONON (compressor
clutch is operat-
ing)
67Stop lamp
switchIgnition switch: ONBrake pedal: De-
pressedOFFProcedure
No.3213A-195
Brake pedal: Re-
leasedON
68EGR valveD
Engine coolant
temperature: 85 -
95_
CIdling2 - 20 STEPProcedure
No.3513A-196
D
Lamps and all
accessories: OFF
D
Transmission: P
range
2,500 r/min0 - 10 STEP
74Fuel pres-
sure sensorD
Engine coolant
temperature: 85 -
95_
CEngine: Cranking2 MPa or moreCode No.
5613A-151
D
Lamps and all
accessories: OFF
D
Transmission: P
range
Engine: Idling4.0 - 6.9 MPa


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-202
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
77Accelerator
pedal posi-Ignition switch: ONRelease the acceler-
ator pedal.985 - 1,085 mVCode No.
7713A-154
tion sensor
(2nd chan-
nel)
Depress the acceler-
ator pedal gradually.Increases in re-
sponse to the
pedal depression
stroke.
Depress the acceler-
ator pedal fully.4,000 mV or more
78Accelerator
pedal posi-Ignition switch: ONRelease the acceler-
ator pedal.985 - 1085 mVCode No.
7813A-156
tion sensor
(1st chan-
nel)
Depress the acceler-
ator pedal gradually.Increases in re-
sponse to the
pedal depression
stroke.
Depress the acceler-
ator pedal fully.4,000 mV or more
79Throttle
positionDEngine: After hav-
ing warmed upRelease the acceler-
ator pedal.400 - 800 mVCode No.
7913A-158
sensor (1st
channel)DIgnition switch: ON
(Engine stopped)
Depress the acceler-
ator pedal gradually.Increases in re-
sponse to the
pedal depression
stroke.
Depress the acceler-
ator pedal fully.4,200 - 4,800 mV
Engine: Idling afterNo load450 - 1,000 mV
warming-up
A/C switch: OFF to
ONIncreases by 100
- 600 mV
Transmission: P to D
rangeIncreases by 0 -
200 mV.
99Combustion
modeEngine: After having
warmed upIdling
(several minutes af-
ter starting)Compression
lean--
2,500 r/minStoichiometric
feedback
Race the engine sud-
denly while the en-
gine is idling.Open loop


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-203
ACTUATOR TEST REFERENCE TABLE
Item
No.Inspection
itemDrive ContentsInspection contentsNormal condi-
tionInspec-
tion pro-
cedure
No.Reference
page
01InjectorCut fuel to the
No.1 injector.Engine:
Idling after warming-upIdling condition
becomes differ-Code
No. 4113A-147
02Cut fuel to the
No.2 injector.
(Cut the fuel supply to each
injector in turn and check
cylinders which does notent (becomes
unstable, or the
engine stalls).
03Cut fuel to the
No.3 injector.affect idling.)
04Cut fuel to the
No.4 injector.
05Cut fuel to the
No.5 injector.
06Cut fuel to the
No.6 injector.
07Fuel pump
(low-pres-
sure)Operates the
fuel pump (low-
pressure) to cir-
culate fuel.Ignition
switch:
ONPinch the return
hose with fin-
gers to feel the
pulse of the fuel
being circulated.Pulse is felt.Proce-
dure
No.2913A-193
Operating
sound can be
heard around
the fuel tank.Sound of opera-
tion can be
heard
08Purge con-
trol solenoid
valveSolenoid valve
turns from OFF
to ON.Ignition switch: ONSound of opera-
tion can be
heard when so-
lenoid valve is
driven.Proce-
dure
No.3613A-197
17Basic ignition
timingSolenoid valve
turns from OFF
to ON.DEngine: Idling
DSet a timing light.
5_BTDC--
21Condenser
fanDrive the fan
motorDIgnition switch: ON
DA/C switch: ON
Fan motor runsProce-
dure
No.2113A-187
34Electronic-
controlled
throttle valve
systemStop the throttle
control servoIgnition switch: ONThe throttle
valve opens
slightlyCode
No. 9113A-161


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

C
heck it e m C
heck co ndit io n (E ngin e co ndit io n) N
orm alco ndit io n 1 N
o.1 in je cto r W
hile engin e is id lin g afte r havin g warm ed up, F
ro m 9-13 V, m om en- 9 N
o.2 in je cto r s
u ddenly depre ss th e acce le ra to r pedal. t
a rily dro ps slig htly 2
4 N
o.3 in je cto r 2 N
o.4 in je cto r 1
0 N
o.5 in je cto r 2
5 N
o.6 in je cto r 3 O
xyg en se nso r heate r E
ngin e: Id lin g 0
-3 V E
ngin e: 5,0 00 r/m in S
yste m vo lt a ge 6 I
n je cto r driv e r re la y I
g nit io n sw it c h : O FF 0
-0.1 V I
g nit io n sw it c h : O N 0
.5 -1.0 V 8 A
lt e rn ato r G te rm in al T
he vo lt a ge in cre ase s
b y 0.2 -3.5 V 5
4 A
lt e rn ato r FR te rm in al T
he vo lt a ge dro ps 1
1 N
o.1 ig nit io n co il E
ngin e sp eed: 3,0 00 r/m in 0
.3 -3.0 V 3
1 N
o.2 ig nit io n co il 1
3 N
o.3 ig nit io n co il 3
0 N
o.4 ig nit io n co il 1
2 N
o.5 ig nit io n co il 3
2 N
o.6 ig nit io n co il 1
4 T
hro ttle co ntr o l se rv o I
g nit io n sw it c h : O FF 0
-0.1 V r
e la y I
g nit io n sw it c h : O N 0
.5 -1.0 V

GDI -Troubleshooting <A/T>13A-205
Terminal
No.Normal condition Check condition (Engine condition) Check item
18Condenser fan relayCondenser fan not operatingSystem voltage
Condenser fan operating0 - 3 V or more
19Air flow sensor resetEngine: Idling0-1V
signal
Engine speed: 3,000 r/min6-9V
20A/C relayDEngine: Idling
DA/C switch: OFF to ON (Compressor operating)System voltage or
changes momentarily 6
V or more to 0 - 3 V
21Fuel pump relayIgnition switch: ONSystem voltage
Engine: Idling0-3V
22Engine warning lampIgnition switch: OFF to ONSystem voltage
23GDI ECO indication
lampIgnition switch: OFF to ON0 - 3 V (system voltage
after five seconds)
Rev the engine suddenly.System voltage
34Purge control solenoidDEngine coolantEngine: stoppedSystem voltage
valvetemperature: 80 -
95_C
DIgnition switch:
ON
Engine: After starting, in-
crease the engine speed
up to 3,500 r/minThe voltage drops
41Power supplyIgnition switch: ONSystem voltage
47
43Engine ignition signalEngine speed: 3,000 r/min0.3 - 3.0 V
44Engine coolant tem-
perature sensorIgnition switch: ONWhen engine coolant tem-
perature is 0_C3.2 - 3.8 V
When engine coolant tem-
perature is 20_C2.3 - 2.9 V
When engine coolant tem-
perature is 40_C1.3 - 1.9 V
When engine coolant tem-
perature is 80_C0.3 - 0.9 V
45Crank angle sensorEngine: Cranking0.4 - 4.0 V
Engine: Idling1.5 - 2.5 V
46Power supply voltage
applied to accelerator
pedal position sensor
(1st channel)Ignition switch: ON4.5 - 5.5 V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-206
Terminal
No.Normal condition Check condition (Engine condition) Check item
49Engine control relayIgnition switch: OFF0-3V
Ignition switch: ONSystem voltage
51EGR valve (A)Ignition switch: OFF to ON5-8V
53EGR valve (C)
(Repeatedly changes
for approx. 3 seconds)
60EGR valve (B)
62EGR valve (C)
52Power steering fluid
pressure switchEngine: Idling after
warming-upWhen steering wheel is
stationarySystem voltage
When steering wheel is
turned0-3V
55Barometric pressureIgnition switch: ONAt an altitude of 0 m3.7 - 4.3 V
sensor
At an altitude of 1,200 m3.2 - 3.8 V
56Camshaft position sen-Engine: Cranking0.4 - 3.0 V
sor
Engine: Idling0.5 - 2.0 V
58Ignition switch-STEngine: Cranking8 V or more
61A/C switch 2Refer to GROUP 55 - Troubleshooting (Check at A/C-ECU or Engine-ECU
Terminal).
63Injector open circuit
check signalEngine: Increases from idling up to 4,000 r/minThe voltage decreases
slightly (approx. 0.7 V)
from 4.5 - 5.0 V.
64Intake air temperature
sensorIgnition switch: ONWhen intake air tempera-
ture is 0_C3.2 - 3.8 V
When intake air tempera-
ture is 20_C2.3 - 2.9 V
When intake air tempera-
ture is 40_C1.5 - 2.1 V
When intake air tempera-
ture is 80_C0.4 - 1.0 V
65Air flow sensorEngine: Idling2.2 - 3.2 V
Engine speed: 2,500 r/min
66Backup power supplyIgnition switch: OFFSystem voltage
71Oxygen sensorEngine: Running at 2,500 r/min after warming-up
(Check by using a digital voltmeter.)Voltages of 0 V and 0.8
V alternate


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk