NISSAN ALMERA TINO 2001 Service Repair Manual

MODELS WITH FUSE AND FUSIBLE LINK BOX E90NLEL0457S02
YEL427C
FRONT WIPER AND WASHER
Wiring Diagram Ð WIPER Ð (Cont'd)
EL-180

YEL428C
FRONT WIPER AND WASHER
Wiring Diagram Ð WIPER Ð (Cont'd)
EL-181

SEL543TA
Removal and InstallationNLEL0060WIPER ARMSNLEL0060S011. Prior to wiper arm installation, turn on wiper switch to operate
wiper motor and then turn it ªOFFº (Auto Stop).
2. Lift the blade up and then set it down onto glass surface to set
the blade center to clearance ªL
1º&ªL2º immediately before
tightening nut.
3. Eject washer fluid. Turn on wiper switch to operate wiper motor
and then turn it ªOFFº.
4. Ensure that wiper blades stop within clearance ªL
1º&ªL2º.
Clearance ªL
1º: 20.4 - 34.4 mm (0.803 - 1.354 in)
Clearance ªL
2º: 61.8 - 75.8 mm (2.433 - 2.984 in)
+Tighten wiper arm nuts to specified torque.
Front wiper: 21 - 26 N´m (2.1 - 2.7 kg-m, 16 - 19 ft-lb)
SEL024J
+Before reinstalling wiper arm, clean up the pivot area as
illustrated. This will reduce possibility of wiper arm loose-
ness.
WIPER LINKAGENLEL0060S02
NEL719
FRONT WIPER AND WASHER
Removal and Installation
EL-182

RemovalNLEL0060S02011. Remove wiper arms and cowl top cover.
2. Remove wiper motor connector.
3. Remove 5 screws and 3 nuts.
4. Remove wiper linkage.
Be careful not to break ball joint rubber boot.
InstallationNLEL0060S0202+Grease ball joint portion before installation.
1. Installation is the reverse order of removal.
GEL013-A
Washer Nozzle AdjustmentNLEL0061+Adjust washer nozzle with suitable tool as shown in the figure
at left.
Adjustable range:±10É (In any direction)
NEL720
Unit: mm (in)
*1 646.9 (25.47) *5 230.1 (9.06)
*2 470.2 (18.51) *6 16.8 (0.66)
*3 332.9 (13.11) *7 356.5 (14.04)
*4 550.9 (21.69) *8 394.8 (15.54)
*: The diameters of these circles are less than 80 mm (3.15 in).
Washer Tube LayoutNLEL0062
NEL725
FRONT WIPER AND WASHER
Removal and Installation (Cont'd)
EL-183

Wiring Diagram Ð WIP/R ÐNLEL0458MODELS WITH INTERMITTENT REAR WIPERNLEL0458S01
YEL905B
REAR WIPER AND WASHER
Wiring Diagram Ð WIP/R Ð
EL-184

YEL906B
REAR WIPER AND WASHER
Wiring Diagram Ð WIP/R Ð (Cont'd)
EL-185

MODELS WITHOUT INTERMITTENT REAR WIPERNLEL0458S02
YEL429C
REAR WIPER AND WASHER
Wiring Diagram Ð WIP/R Ð (Cont'd)
EL-186

YEL906B
REAR WIPER AND WASHER
Wiring Diagram Ð WIP/R Ð (Cont'd)
EL-187

NEL722
Removal and InstallationNLEL0301WIPER ARMSNLEL0301S011. Prior to wiper arm installation, turn on wiper switch to operate
wiper motor and then turn it ªOFFº (Auto Stop).
2. Lift the blade up and then set it down onto glass surface. Set
the black center to clearance ªEº immediately before tighten-
ing the nut.
3. Eject washer fluid. Turn on wiper switch to operate wiper motor
and then turn it ªOFFº.
4. Ensure that wiper blades stop on the lowest heat wire.
+Tighten windshield wiper arm nuts to specified torque.
: 12.7 - 17.6 N´m (1.3 - 1.8 kg-m, 10 - 13 ft-lb)
SEL024J
+Before reinstalling wiper arm, clean up the pivot area as
illustrated. This will reduce possibility of wiper arm loose-
ness.
NEL721
Washer Nozzle AdjustmentNLEL0302The diameter of the washer spit circle is less than 30 mm (1.18 in).
REAR WIPER AND WASHER
Removal and Installation
EL-188

Washer Tube LayoutNLEL0303
NEL723
REAR WIPER AND WASHER
Washer Tube Layout
EL-189