NISSAN NOTE 2016 Service Repair Manual

MWI
SYSTEMMWI-63
< SYSTEM DESCRIPTION > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
SPEEDOMETER
SPEEDOMETER : System DescriptionINFOID:0000000012432603
SYSTEM DIAGRAM
DESCRIPTION
The ABS actuator and electric unit (control unit) receives each wheel speed sensor signal and provides a vehi-
cle speed signal to the combination meter via CAN communication.
TACHOMETER
Information display Trip com-
puterCurrent fuel consump-
tion
• When reception time of an abnormal signal is 2 seconds or
less, the last received datum is used for calculation to indi-
cate the result.
• When reception time of an abnormal signal is more than two seconds, the last result calculated during normal condition is
indicated.
Average fuel consump-
tion
Distance to empty
Odo/trip meter An indicated value is maintained at communications blackout.
Buzzer The buzzer turns OFF by suspending communication.
Warning lamp/indicator lamp ABS warning lamp
The lamp turns ON by suspending communication.
Slip indicator lamp
Malfunction indicator lamp (MIL)
VDC OFF indicator lamp
EPS warning lamp
Brake warning lamp
High beam indicator lamp
The lamp turns OFF by suspending communication.
Turn signal indicator lamp
Door warning lamp
Light indicator lamp
Engine oil pressure warning lamp
High water temperature warning
lamp
Key warning lamp
O/D OFF indicator lamp
Shift P warning lamp
Engine start operation indicator lamp
Function
Specifications
AWNIA2379GB
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI-64
< SYSTEM DESCRIPTION >[TYPE B]
SYSTEM
TACHOMETER : System Description
INFOID:0000000012432604
SYSTEM DIAGRAM
DESCRIPTION
The crank position sensor sends a crankshaft positi on signal to the ECM. The ECM provides an engine speed
signal to the combination meter via CAN communication lines. The tachometer indicates engine speed in rev-
olutions per minute (rpm).
SHIFT POSITION INDICATOR
SHIFT POSITION INDICATO R : System DescriptionINFOID:0000000012432605
SYSTEM DIAGRAM
DESCRIPTION
The combination meter receives the shift position signal from TCM via CAN communication, and displays the
position of the shift indicator.
HIGH WATER TEMPERATURE WARNING LAMP
HIGH WATER TEMPERATURE WARNING LAMP : System DescriptionINFOID:0000000012432606
SYSTEM DIAGRAM
DESCRIPTION
The ECM monitors the engine coolant temperature fr om the engine coolant temperature sensor. When the
coolant temperature is above the s pecified value, the ECM sends a CAN communication signal to the combi-
nation meter turning on the high temperature warning lamp.
JSNIA2462GB
AWNIA3497GB
JSNIA4067GB
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI
SYSTEMMWI-65
< SYSTEM DESCRIPTION > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
Timing Chart
OIL PRESSURE WARNING LAMP
OIL PRESSURE WARNING LAMP
: System DescriptionINFOID:0000000012432607
SYSTEM DIAGRAM
DESCRIPTION
The combination meter turns the engine oil pressure warning lamp ON when receiving a signal from the ECM
via CAN communication.
METER ILLUMINATION CONTROL
JSNIA3281GB
AWNIA2885GB
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI-66
< SYSTEM DESCRIPTION >[TYPE B]
SYSTEM
METER ILLUMINATION CONTRO L : System Description
INFOID:0000000012432608
SYSTEM DIAGRAM
DESCRIPTION
• Combination meter controls meter illumination, based on the following signal.
- Position light request signal
• The combination meter turns ON meter illumination when the following conditions are satisfied.
• The combination meter turns OFF meter illumination when the following conditions are satisfied.
INFORMATION DISPLAY
INFORMATION DISPLAY : System DescriptionINFOID:0000000012432609
SYSTEM DIAGRAM
DESRIPTION
• The combination meter receives signals from swit ches, sensors and modules for operating the following
functions on the information display.
- Odo/trip meter
- Fuel gauge
- Trip computer
- Interrupt indication
- Meter illumination level
- Low fuel warning
- Outside air temperature
JSNIA2919GB
Condition
Combination switch (Lighting switch) 1st or 2nd position
Condition
Combination switch (Lighting switch) OFF
AWNIA3658GB
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI
SYSTEMMWI-67
< SYSTEM DESCRIPTION > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
- Loose fuel cap warning
ODO/TRIP METER
The combination meter calculates mileage using the vehicle speed signal from the ABS actuator and electric
unit (control unit) and displays the mileage on the information display.
FUEL GAUGE
Control Outline
The fuel level sensor unit sends a variable resistor si gnal to the combination meter. The fuel gauge indicates
the approximate fuel level in the fuel tank.
Refuel Control
The unit detects the driver is refueling the vehicle and accelerates the fuel gauge segment movement if the
fuel level changes by 9 (2-3/8 US, 2 lmp gal) or more.
Lighting segment-resistance relationship
INTERRUPT INDICATION
Low Fuel Warning
The low fuel warning turns ON when the fuel level in t he fuel tank reaches approximately 7.3 (1-7/8 US gal,
1-5/8 Imp gal).
OUTSIDE AIR TEMPERATURE INDICATION
Displays the outside temperature based on the signal received from the ambient sensor.
LOOSE FUEL CAP WARNING
The LOOSE FUEL CAP message will display in the informat ion display when the fuel-filler cap is not tightened
correctly. The message will turn off as soon as the ECM detects the fuel-filler cap is properly tightened. The
ECM provides a loose fuel cap signal to the combination meter via CAN communication lines.
AWNIA3088GB
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI-68
< SYSTEM DESCRIPTION >[TYPE B]
OPERATION
OPERATION
Switch Name and FunctionINFOID:0000000012432610
ILLUMINATION CONTROL SWITCH/
TRIP ODOMETER RESET SWITCH
STEERING WHEEL AUDIO CONTROL SWITCH (METER CONTROL SWITCH)
AWNIA3606ZZ
Switch name Operation Description
Illumination control switch (1) Turn An illuminance level of the back light of the combination meter can be adjusted.
Trip odometer reset switch (1) Press • The information display screen can be switched.
• The trip meter can be switched between A and B.
• Trip meter A/B can be reset by pressing and holding the trip reset switch.
• Time can be adjusted.
AWNIA3620GB
Switch name
Operation Description
Steering wheel audio control switch
(meter control switch) (2) Press• Trip computer modes can be selected.
• Trip computer value displayed can be reset by pressing and holding the meter
control switch for 1 second or more.
• All trip computer values displayed can be reset by pressing and holding the
meter control switch for 3 seconds or more.
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI
DIAGNOSIS SYSTEM (COMBINATION METER)MWI-69
< SYSTEM DESCRIPTION > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
DIAGNOSIS SYSTEM (C OMBINATION METER)
On Board Diagnosis FunctionINFOID:0000000012432611
ON BOARD DIAGNOSIS
The following meter functions can be checked during Combination Meter Self-Diagnosis Mode:
• Pointer sweep of speedometer, tachometer and gauges.
• Illumination of all lamps/LEDs that are controlled by the combination meter (regardless of switch status).
• Error code
STARTING COMBINATION ME TER SELF-DIAGNOSIS MODE
NOTE:
• Check combination meter power supply and ground circuits if self-diagnosis mode does not start. Refer to
MWI-98, "
COMBINATION METER : Diagnosis Procedure". Replace combination meter if power supply and
ground circuits are found to be normal and self-diagnosis mode does not start. Refer to MWI-115, "
Removal
and Installation".
• Combination meter self-diagnosis mode will function with the ignition switch in ON. Combination meter self-
diagnosis mode will exit upon turning the ignition switch to OFF.
METHOD OF STARTING
1. Turn ignition switch to OFF.
2. While pressing the trip reset switch (1), turn the ignition switch ON.
3. Press the trip reset switch at least 3 times. (Within 7 seconds
after the ignition switch is turned ON.)
4. All LCD segments turn ON. NOTE:
If any of the segments are not activa ted, replace the combination meter.
5. The mode switches in the order shown below each time the trip reset switch is pressed. NOTE:
• If the trip reset switch is not operated for 20 sec onds or more, the self-diagnosis mode is automatically
cancelled.
• When the trip reset switch is pressed during the indica tion of Test order “10,” test item returns to Test
order “2.”
AWNIA3606ZZ
AWNIA3625ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI-70
< SYSTEM DESCRIPTION >[TYPE B]
DIAGNOSIS SYSTEM (COMBINATION METER)
*1: Error code A-D
*2: Error code E-H
Test order
Test item Description
1 Work instruction code
This item is displayed, but not used.
2 Part number
3 Software code
4 EEPROM code
5 Hardware code
6 P.C.B code
7 Circuit check
The pointer of the following items moves from 0 to MAX twice.
• Speedometer
• Tachometer
NOTE:
If any one of the pointers does not sweep, replace combination meter.
8 Error code A-D
*1
Displays the error code of the following items:
• High water temperature indicator
• Fuel gauge
• Tachometer
• Speedometer
9 Error code E-H
*2Displays the error code of the following item:
• Meter control switch
10 All warning/indicator lamp illuminate.
NOTE:
• When either one of them does not turn ON, replace combination meter.
AWNIA3626ZZ
AWNIA3627ZZ
Item
Code Description Action to take/Reference
High water tempera-
ture indicator signal 0Normal
—
1 An engine coolant temperature signal cannot be
received from ECM. Perform “Self Diagnostic Result” of “ECM.”
Refer to
EC-87, "
DTCIndex".
Fuel gauge 0Normal
—
1 Fuel gauge circuit is shorted. Refer to MWI-101, "
DiagnosisProcedure".
2 Fuel gauge circuit is open.
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI
DIAGNOSIS SYSTEM (COMBINATION METER)MWI-71
< SYSTEM DESCRIPTION > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
CONSULT Function (METER/M&A)INFOID:0000000012432612
APPLICATION ITEMS
CONSULT can display each diagnostic item using the diagnostic test modes shown.
SELF DIAG RESULT
Refer to MWI-77, "DTC Index".
DATA MONITOR
Display Item List
X: Applicable
Tachometer 0Normal
—
1 An engine speed signal cannot be received from
ECM. Perform “Self Diagnostic Result” of “ECM.”
Refer to EC-87, "
DTCIndex".
Speedometer 0Normal
—
1 A vehicle speed signal cannot be received from
ABS actuator and electric
unit (control unit).
Perform “Self Diagnostic Result” of “ABS.”
Refer to BRC-43, "
DTC Index".
2 A vehicle speed si
gnal received from the ABS ac-
tuator and electric unit (control unit) is abnormal.
— 0 Displays “0” constantly. —
— 0 Displays “0” constantly. —
— 0 Displays “0” constantly. —
Trip odometer reset
switch 0Normal
—
2 When judging that the trip odometer reset switch
signal circuit is short-circuited for 5 minutes or
more. Replace combination meter.
Refer to MWI-115, "
Removal and Installa-
tion".
Item Code Description Action to take/Reference
METER/M&A Diagnosis mode
Description
Self Diagnostic Result The combination meter self-diagnosis results.
Data Monitor Displays combination meter input/output data in real time.
Work support Supports combination meter diagnosis.
ECU Identification The combination meter part number is displayed.
Warning History Lighting history of the warning lamp and indicator lamp can be checked.
Display item [Unit]MAIN
SIGNALS Description
SPEED METER
[mph] or [km/h] X Displays the value of vehicle speed signal.
SPEED OUTPUT
[mph] or [km/h] XDisplays the value of vehicle speed signal, which is transmitted to each unit with
CAN communication.
ODO OUTPUT
[mph] or [km/h] Displays odometer signal value transmitted to other units via CAN communica-
tion.
TACHO METER
[rpm] X Displays the value of engine speed signal, which is input from ECM.
FUEL METER
[L] X Displays the fuel level.
W TEMP METER
[ ° C] or [ °F] X Displays the value of engine coolant temperature signal, which is input from ECM.
ABS W/L
[On/Off] Displays [ON/OFF] condition of ABS warning indicator
Revision: August 2015
2016 Versa Note

cardiagn.com

MWI-72
< SYSTEM DESCRIPTION >[TYPE B]
DIAGNOSIS SYSTEM (COMBINATION METER)
VDC/TCS IND
[ON/OFF]Displays [ON/OFF] condition of VDC OFF indicator lamp.
SLIP IND
[ON/OFF] Displays [ON/OFF] condition of SLIP indicator lamp.
BRAKE W/L
[On/Off] Displays [ON/OFF] condition of brake warning indicator.
DOOR W/L
[On/Off] Displays [ON/OFF] condition of door warning indicator.
HI-BEAM IND
[On/Off] Displays [ON/OFF] condition of high beam indicator.
TURN IND
[On/Off] Displays [ON/OFF] condition of turn indicator.
LIGHT IND
[On/Off] Displays [ON/OFF] condition of light indicator.
OIL W/L
[On/Off] Displays [ON/OFF] condition of engine oil pressure warning indicator.
MIL
[On/Off] Displays [ON/OFF] condition of malfunction indicator.
CRUISE IND
[Off] Displays [ON/OFF]
condition of CRUISE indicator.
O/D OFF IND
[On/Off] Displays [ON/OFF] condition of O/D OFF indicator.
FUEL W/L
[On/Off] Displays [ON/OFF] condition of
low-fuel warning indicator.
PASS BUCKLE SW
[On/Off] Status of seat belt buckle switch RH.
AIR PRES W/L
[ON/OFF] Displays [ON/OFF] condition of tire pressure warning lamp.
KEY G/Y W/L
[ON/OFF] Displays [ON/OFF] condition of key warning lamp.
EPS W/L
[On/Off] Displays [ON/OFF] condition of EPS indicator.
FUEL CAP W/L
[Off] Displays [ON/OFF] condition of loose fuel cap warning message.
PKB SW
[On/Off] Status of parking brake switch.
BUCKLE SW
[On/Off] Status of seat belt buckle switch (LH).
BRAKE OIL SW
[On/Off] Status of brake fluid level switch.
CHG SIG
[On/Off] Displays [ON/OFF] condition of charge warning indicator.
DISTANCE
[km] or [Mi] Displays distance to empty.
OUTSIDE TEMP
[ ° F] or [ °C] Displays the ambient temperature, which is input from ambient sensor.
FUEL LOW SIG
[ON/OFF] Displays [ON/OFF] condition
of low-fuel warning signal.
BUZZER
[On/Off] X Displays [ON/OFF] condition of buzzer.
Display item [Unit]
MAIN
SIGNALS Description
Revision: August 2015
2016 Versa Note

cardiagn.com