NISSAN NOTE 2016 Service Repair Manual

DOOR MIRROR GLASSMIR-17
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
K
M A
B
MIR
N
O P
DOOR MIRROR GLASS
Removal and InstallationINFOID:0000000012432094
REMOVAL
1. Place a piece of protective tape on the mirror housing.
2. Tilt the door mirror glass upward (1).
3. Remove the door mirror glass lower side, using a suitable tool (A) in the recess between door mirror glass (1) and actuator (2)
and push up on pawls and rotate (twist).
4. Disconnect harness connector from door mirror glass (if equipped with heated mirrors).
5. Remove the glass using a suitable tool in the (LH/RH) recesses between door mirror glass and actuator and push up on pawls
and rotate (twist).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
After installation, visually check that pawls are securely engaged.
ALLIA1036ZZ
ALLIA1037ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

MIR-18
< REMOVAL AND INSTALLATION >
DOOR MIRROR REAR FINISHER
DOOR MIRROR REAR FINISHER
Removal and InstallationINFOID:0000000012432095
REMOVAL
1. Remove door mirror glass. Refer to MIR-17, "Removal and Installation".
2. Release pawls using a suitable tool and remove door mirror rear finisher from the door mirror.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Visually check door mirror rear finisher pawls fo r deformation and damage during installation.
Revision: August 2015 2016 Versa Note

cardiagn.com

DOOR MIRROR REMOTE CONTROL SWITCHMIR-19
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
K
M A
B
MIR
N
O P
DOOR MIRROR REMOTE CONTROL SWITCH
Removal and InstallationINFOID:0000000012432096
REMOVAL
1. Remove the instrument lower panel LH. Refer to IP-15, "Removal and Installation".
2. Remove door mirror remote control switch (1) from the instru- ment lower panel LH using a suitable tool.
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
AWLIA2157ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

PB-1
BRAKES
C
DE
G H
I
J
K L
M
SECTION PB
A
B
PB
N
O P
CONTENTS
PARKING BRAKE SYSTEM
PRECAUTION ....... ........................................2
PRECAUTIONS .............................................. .....2
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
2
PREPARATION ............................................3
PREPARATION .............................................. .....3
Commercial Service Tool .................................... ......3
PERIODIC MAINTENANCE ..........................4
PARKING BRAKE SYSTEM .......................... .....4
Inspection and Adjustment .................................. ......4
REMOVAL AND INSTALLATION ................6
PARKING BRAKE CONTROL ...........................6
Exploded View ..................................................... .....6
Removal and Installation ..........................................6
PARKING BRAKE CABLE ................................7
Removal and Installation ..........................................7
PARKING BRAKE REAR CABLE .....................8
Removal and Installation ..........................................8
PARKING BRAKE SWITCH ..............................9
Removal and Installation ..........................................9
SERVICE DATA AND SPECIFICATIONS
(SDS) ............... .......................................... ...
10
SERVICE DATA AND SPECIFICATIONS
(SDS) .................................................................
10
Parking Brake Control ......................................... ....10
Revision: August 2015 2016 Versa Note

cardiagn.com

PB-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012430686
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Revision: August 2015 2016 Versa Note

cardiagn.com

PREPARATIONPB-3
< PREPARATION >
C
DE
G H
I
J
K L
M A
B
PB
N
O P
PREPARATION
PREPARATION
Commercial Service ToolINFOID:0000000012430687
Tool name Description
Power tool Loosening nuts, screws and bolts
PIIB1407E
Revision: August 2015 2016 Versa Note

cardiagn.com

PB-4
< PERIODIC MAINTENANCE >
PARKING BRAKE SYSTEM
PERIODIC MAINTENANCE
PARKING BRAKE SYSTEM
Inspection and AdjustmentINFOID:0000000012430688
INSPECTION
Parking Brake Control Stroke
1. When parking brake control is operated with a force of 196 N(20.0 kg-f, 44.1 lb-f), make sure parking brake control stroke is
within the specified number of notches. (Check by listening and
counting the number of ratchet clicks.)
2. Check that the parking brake lamp illuminates, after parking brake has been operated to the specified number of notches.
Inspect Components
• Check the parking brake components for bends, wear and or damage. Replace if any damage is noted.
• Check that the parking brake operates properly ; be sure that it is not bound up or sticking.
• Check that the brake warning light illuminates afte r parking brake has been operated to the specified number
of notches. Refer to PB-10, "
Parking Brake Control".
• Inspect and adjust the rear brakes if necessary. Refer to BR-43, "
Inspection and Adjustment".
ADJUSTMENT
1. Pull parking brake control (1) until the access hole (2) is visible.
Use suitable tool to adjust nut (A).
2. Turn adjusting nut (A) using suitable tool to loosen the front cable.
3. Depress the brake pedal with a force of 196 N (20. 0 kg-f, 44.1 lb-f) about 10 times and adjust the brake
shoe clearance.
4. Adjust the cable with the following procedure. CAUTION:Number of
notches
: Refer to PB-10, "
Parking Brake
Control".
Number of
notches : Refer to PB-10, "
Parking Brake
Control".
WFIA0508E
AWFIA1013ZZ
Revision: August 2015
2016 Versa Note

cardiagn.com

PARKING BRAKE SYSTEMPB-5
< PERIODIC MAINTENANCE >
C
DE
G H
I
J
K L
M A
B
PB
N
O P
To prevent damage to parts, do not bend the parking brake cables.
a. Adjust the parking brake lever stroke by turning the adjusting nut using suitable tool.
CAUTION:
Do not reuse the adjusting nut if the nut is removed.
b. Operate the parking brake lever with a force of 196 N (20.0 kg-f, 44.1lb-f). Check that the lever stroke is
within the specified number of notches. (Check by li stening and counting the number of the ratchet clicks.)
Number of notches : Refer to PB-10, "
Parking Brake Control".
Revision: August 2015 2016 Versa Note

cardiagn.com

PB-6
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
REMOVAL AND INSTALLATION
PARKING BRAKE CONTROL
Exploded ViewINFOID:0000000012430689
Removal and InstallationINFOID:0000000012430690
REMOVAL
1. Remove the center console assembly. Refer to IP-18, "Removal and Installation".
2. Remove the adjusting nut. CAUTION:
Do not reuse the adjusting nut.
3. Separate the parking brake front cable fr om the parking brake rear cables (RH/LH).
4. Disconnect the harness connector fr om the parking brake switch.
5. Remove the screw and remove the parking brake switch.
6. Remove the nuts and remove the parking brake control.
INSTALLATION
Installation is in the reverse order of the removal.
CAUTION:
• Replace the parking brake control if it h as been dropped or sustained an impact.
• Replace the parking brake switch if it h as been dropped or sustained an impact.
• Do not reuse the adjusting nut.
Inspect and adjust the parking brake. Refer to PB-4, "
Inspection and Adjustment".
1. Parking brake control2. Adjusting nut3. Parking brake switch
4. Parking brake front cable 5. Parking brake rear cable (LH) 6. Parking brake rear cable (RH)
JPFIB0133GB
Revision: August 2015 2016 Versa Note

cardiagn.com

PARKING BRAKE CABLEPB-7
< REMOVAL AND INSTALLATION >
C
DE
G H
I
J
K L
M A
B
PB
N
O P
PARKING BRAKE CABLE
Removal and InstallationINFOID:0000000012430691
REMOVAL
1. Remove the center console assembly. Refer to IP-18, "Removal and Installation".
2. Remove the adjusting nut. Refer to PB-6, "
Exploded View".
3. Separate the parking brake front cable from parking brake rear cables (RH/LH). Refer to PB-6, "
Exploded
View".
CAUTION:
To prevent damage to the parts, do not bend the parking brake cables.
4. Remove the parking brake front cable.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the adjusting nut.
• Inspect and adjust the parking brake. Refer to PB-4, "
Inspection and Adjustment".
Revision: August 2015 2016 Versa Note

cardiagn.com