NISSAN TEANA 2008 Service Manual

EXL-222
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
DIAGNOSIS SYSTEM (IPDM E/R)
ACTIVE TEST
Te s t i t e m
IGN RLY
[Off/On]×Displays the status of the ignition relay judged by IPDM E/R.
PUSH SW
[Off/On]Displays the status of the push-button ignition switch judged by IPDM E/R.
INTER/NP SW
[Off/On]Displays the status of the shift position judged by IPDM E/R.
ST RLY CONT
[Off/On]Displays the status of the starter relay status signal received from BCM via CAN
communication.
IHBT RLY -REQ
[Off/On]Displays the status of the starter control relay signal received from BCM via CAN
communication.
ST/INHI RLY
[Off/ ST /INHI/UNKWN]Displays the status of the starter relay and starter control relay judged by IPDM
E/R.
DETENT SW
[Off/On]Displays the status of the control device (detention switch) judged by IPDM E/R.
S/L RLY -REQ
[Off/On]Displays the status of the steering lock relay signal received from BCM via CAN
communication.
S/L STATE
[LOCK/UNLOCK/UNKWN]Displays the status of the steering lock judged by IPDM E/R.
DTRL REQ
[Off]NOTE:
The item is indicated, but not monitored.
OIL P SW
[Open/Close]Displays the status of the oil pressure switch judged by IPDM E/R.
HOOD SW
[Off/On]Displays the status of the hood switch judged by IPDM E/R.
HL WASHER REQ
[Off]Display the status of the headlamp washer request signal received from BCM via
CAN communication.
THFT HRN REQ
[Off/On]Displays the status of the theft warning horn request signal received from BCM
via CAN communication.
HORN CHIRP
[Off/On]Displays the status of the horn reminder signal received from BCM via CAN com-
munication.
CRNRNG LMP REQ
[Off]NOTE:
The item is indicated, but not monitored. Monitor Item
[Unit]MAIN SIG-
NALSDescription
Test item Operation Description
CORNERING LAMPOff
NOTE:
The item is indicated, but cannot be tested. LH
RH
HORN On Operates horn relay for 20 ms.
FRONT WIPEROff OFF
Lo Operates the front wiper relay.
Hi Operates the front wiper relay and front wiper high relay.
MOTOR FAN1OFF
2 Operates the cooling fan relay-1.
3 Operates the cooling fan relay-2.
4 Operates the cooling fan relay-2 and cooling fan relay-3.
HEAD LAMP WASHER On Operates the headlamp washer relay for 1 s.

DIAGNOSIS SYSTEM (IPDM E/R)
EXL-223
< FUNCTION DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
EXTERNAL LAMPSOff OFF
TAIL Operates the tail lamp relay.
Lo Operates the headlamp low relay.
HiOperates the headlamp low relay and ON/OFF the headlamp high relay at 1 sec-
ond intervals.
Fog Operates the front fog lamp relay. Test item Operation Description

EXL-224
< COMPONENT DIAGNOSIS >[HALOGEN TYPE]
POWER SUPPLY AND GROUND CIRCUIT
COMPONENT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE) : Diagnosis ProcedureINFOID:0000000003894317
1.CHECK FUSE AND FUSIBLE LINK
Check that the following fuse and fusible link are not blown.
Is the fuse fusing?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown.
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connectors.
3. Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector.
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) : Di-
agnosis Procedure
INFOID:0000000003894318
1.CHECK FUSES AND FUSIBLE LINK
Check that the following IPDM E/R fuses or fusible links are not blown.
Signal name Fuse and fusible link No.
Battery power supplyI
10
Te r m i n a l s
Voltag e
(Approx.) (+) (−)
BCM
Ground Connector Terminal
M118 1
Battery voltage
M119 11
BCM
GroundContinuity
Connector Terminal
M119 13 Existed

POWER SUPPLY AND GROUND CIRCUIT
EXL-225
< COMPONENT DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Is the fuse fusing?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown.
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check voltage between IPDM E/R harness connector and ground.
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between IPDM E/R harness connectors and ground.
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector.
Signal name Fuses and fusible link No.
Battery power supplyE
50
51
Te r m i n a l s
Voltag e
(Approx.) (+)
(−)
IPDM E/R
Connector Terminal
Ground
E9 1 Battery voltage
IPDM E/R
GroundContinuity
Connector Terminal
E10 12
Existed
E11 41

EXL-226
< COMPONENT DIAGNOSIS >[HALOGEN TYPE]
EXTERIOR LAMP FUSE
EXTERIOR LAMP FUSE
DescriptionINFOID:0000000003773678
Fuse list
Diagnosis ProcedureINFOID:0000000003773679
1.CHECK FUSE
Check that the following fuses are not fusing.
Is the fuse fusing?
YES >> Repair the applicable circuit. And then replace the fuse.
NO >> The fuse is normal.
Unit Location Fuse No. Capacity
Headlamp HI (LH) IPDM E/R #54 10 A
Headlamp HI (RH) IPDM E/R #55 10 A
Headlamp LO (LH) IPDM E/R #56 15 A
Headlamp LO (RH) IPDM E/R #57 15 A
Front fog lamp IPDM E/R #58 15 A
Parking lamp IPDM E/R #52 10 A
Tail lamp
 License plate lamp
 Each illuminationIPDM E/R #53 10 A
Stop lamp FUSE BLOCK (J/B) #7 10 A
Back-up lamp FUSE BLOCK (J/B) #4 10 A
Unit Location Fuse No. Capacity
Headlamp HI (LH) IPDM E/R #54 10 A
Headlamp HI (RH) IPDM E/R #55 10 A
Headlamp LO (LH) IPDM E/R #56 15 A
Headlamp LO (RH) IPDM E/R #57 15 A
Front fog lamp IPDM E/R #58 15 A
Parking lamp IPDM E/R #52 10 A
Tail lamp
 License plate lamp
 Each illuminationIPDM E/R #53 10 A
Sto p l am pFUSE
BLOCK (J/B)#7 10 A
Back-up lampFUSE
BLOCK (J/B)#4 10 A

HEADLAMP (HI) CIRCUIT
EXL-227
< COMPONENT DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
HEADLAMP (HI) CIRCUIT
Component Function CheckINFOID:0000000003773680
1.CHECK HEADLAMP (HI) OPERATION
IPDM E/R AUTO ACTIVE TEST
1. Activate IPDM E/R auto active test. Refer to PCS-11, "
Diagnosis Description".
2. Check that the headlamp switches to the high beam.
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the headlamp (HI) is turned ON.
NOTE:
ON/OFF is repeated 1 second each.
Is the headlamp (HI) turned ON?
YES >> Headlamp (HI) circuit is normal.
NO >> Refer to EXL-227, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003773681
1.CHECK HEADLAMP (HI) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Turn the ignition switch OFF.
2. Disconnect the headlamp high connector.
3. Turn the ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5. With operating the test items, check the voltage between the IPDM E/R harness connector and the
ground.
Is the measurement value normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (HI) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the headlamp high harness connector. Hi : Headlamp (HI) ON
Off : Headlamp (HI) OFF
Te r m i n a l s
Te s t i t e m
Vo l ta g e
(Approx.) (+) (−)
IPDM E/R
GroundEXTERNAL
LAMPS
Connector Terminal
RH
E34589HiBattery
voltage
Off 0 V
LH 90HiBattery
voltage
Off 0 V

EXL-228
< COMPONENT DIAGNOSIS >[HALOGEN TYPE]
HEADLAMP (HI) CIRCUIT
Does continuity exist?
YES >> GO TO 5.
NO >> Repair the harnesses or connectors.
3.CHECK HEADLAMP (HI) FUSE
1. Turn the ignition switch OFF.
2. Check that the following fuses are not fusing.
Is the fuse fusing?
YES >> GO TO 4.
NO >> Replace IPDM E/R.
4.CHECK HEADLAMP HIGH (HI) SHORT CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between the IPDM E/R harness connector terminal and the ground.
Does continuity exist?
YES >> Repair the harnesses or connectors. And then replace the fuse.
NO >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
5.CHECK HEADLAMP (HI) GROUND OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect the headlamp high connector.
3. Check continuity between the headlamp high harness connector and ground.
Does continuity exist?
YES >> Replace the headlamp (HI) bulb. (Bulb socket is abnormally.)
NO >> Repair the harnesses or connectors.
IPDM E/R Headlamp high
Continuity
Connector Terminal Connector Terminal
RH
E34589 E317 1
Existed
LH 90 E316 1
Unit Location Fuse No. Capacity
Headlamp HI (RH) IPDM E/R #55 10 A
Headlamp HI (LH) IPDM E/R #54 10 A
IPDM E/R
GroundContinuity
Connector Terminal
RH
E34589
Not existed
LH 90
Headlamp high
GroundContinuity
Connector Terminal
RH E317 2
Existed
LH E316 2

HEADLAMP (LO) CIRCUIT
EXL-229
< COMPONENT DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
HEADLAMP (LO) CIRCUIT
Component Function CheckINFOID:0000000003773682
1.CHECK HEADLAMP (LO) OPERATION
IPDM E/R AUTO ACTIVE TEST
1. Activate IPDM E/R auto active test. Refer to PCS-11, "
Diagnosis Description".
2. Check that the headlamp is turned ON.
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the headlamp (LO) is turned ON.
Is the headlamp (LO) turned ON?
YES >> Headlamp (LO) is normal.
NO >> Refer to EXL-229, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003773683
1.CHECK HEADLAMP (LO) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Turn the ignition switch OFF.
2. Disconnect the front combination lamp connector.
3. Turn the ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5. With operating the test items, check the voltage between the IPDM E/R harness connector and the
ground.
Is the measurement value normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (LO) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the front combination lamp harness con-
nector.Lo : Headlamp (LO) ON
Off : Headlamp (LO) OFF
Te r m i n a l s
Te s t i t e m
Vol tag e
(Approx.) (+) (−)
IPDM E/R
GroundEXTERNAL
LAMPS
Connector Terminal
RH
E34583LoBattery volt-
age
Off 0 V
LH 84LoBattery volt-
age
Off 0 V
IPDM E/R Front combination lamp
Continuity
Connector Terminal Connector Terminal
RH
E34583 E319 3
Existed
LH 84 E318 3

EXL-230
< COMPONENT DIAGNOSIS >[HALOGEN TYPE]
HEADLAMP (LO) CIRCUIT
Does continuity exist?
YES >> GO TO 5.
NO >> Repair the harnesses or connectors.
3.CHECK HEADLAMP (LO) FUSE
1. Turn the ignition switch OFF.
2. Check that the following fuses are not fusing.
Is the fuse fusing?
YES >> GO TO 4.
NO >> Replace IPDM E/R.
4.CHECK HEADLAMP (LO) SHORT CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between the IPDM E/R harness connector and the ground.
Does continuity exist?
YES >> Repair the harnesses or connectors. And then replace the fuse.
NO >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
5.CHECK HEADLAMP (LO) GROUND OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect the front combination lamp connector.
3. Check continuity between the front combination lamp harness connector and ground.
Does continuity exist?
YES >> Replace the headlamp (LO) bulb. (Bulb socket is abnormally.)
NO >> Repair the harnesses or connectors.
Unit Lotion Fuse No. Capacity
Headlamp LO (RH) IPDM E/R #57 15 A
Headlamp LO (LH) IPDM E/R #56 15 A
IPDM E/R
GroundContinuity
Connector Terminal
RH
E34583
Not existed
LH 84
Front combination lamp
GroundContinuity
Connector Terminal
RH E319 4
Existed
LH E318 4

FRONT FOG LAMP CIRCUIT
EXL-231
< COMPONENT DIAGNOSIS >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
FRONT FOG LAMP CIRCUIT
Component Function CheckINFOID:0000000003894319
1.CHECK FRONT FOG LAMP OPERATION
IPDM E/R AUTO ACTIVE TEST
1. Activate IPDM E/R auto active test. Refer to PCS-11, "
Diagnosis Description".
2. Check that the front fog lamp is turned ON.
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the front fog lamp is turned ON.
Is the front fog lamp turned ON?
YES >> Front fog lamp circuit is normal.
NO >> Refer to EXL-231, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003894320
1.CHECK FRONT FOG LAMP FUSE
1. Turn the ignition switch OFF.
2. Check that the following fuse is not fusing.
Is the fuse fusing?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK FRONT FOG LAMP SHORT CIRCUIT
1. Disconnect IPDM E/R connector and the front fog connector.
2. Check continuity between the IPDM E/R harness connector and the ground.
Does continuity exist?
YES >> Repair the harnesses or connectors. And then replace the fuse.
NO >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
3.CHECK FRONT FOG LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES >> GO TO 4.
NO >> Replace the bulb.
4.CHECK FRONT FOG LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect the front fog lamp connector.
2. Turn the ignition switch ON.
3. Select “EXTERNAL LAMPS” of IPDM E/R active test item. Fog : Front fog lamp ON
Off : Front fog lamp OFF
Unit Location Fuse No. Capacity
Front fog lamp IPDM E/R #58 15 A
IPDM E/R
GroundContinuity
Connector Terminal
RH
E34586
Not existed
LH 87