NISSAN TEANA 2008 Service Manual

AV
PRESET SWITCH
AV-177
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
PRESET SWITCH
Exploded ViewINFOID:0000000003940168
REMOVAL
Refer to IP-11, "Exploded View".
DISASSEMBLY
Removal and InstallationINFOID:0000000003940169
REMOVAL
1. Remove cluster lid C. Refer to IP-12, "Removal and Installation".
2. Remove preset switch mounting screws.
3. Remove preset switch.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
When installing preset switch, do not allow the print wire that connects preset switch and multifunction switch
to get caught in between AV control unit and preset switch.
1. Preset switch 2. Cluster lid C
JPNIA1044ZZ
1. Preset switch
A. Screw
B. Screw
JPNIA1045ZZ

AV-178
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
REAR CONTROL SWITCH
REAR CONTROL SWITCH
Exploded ViewINFOID:0000000003940170
REMOVAL
Refer to SE-98, "Exploded View".
DISASSEMBLY
Removal and InstallationINFOID:0000000003940171
REMOVAL
1. Remove rear control switch, stretching pawls of armrest assembly.
2. Disconnect rear control switch connector.
3. Remove rear control switch.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1046ZZ
1. Rear control switch
A. Clip

AV
AUXILIARY INPUT JACKS
AV-179
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
AUXILIARY INPUT JACKS
Exploded ViewINFOID:0000000003940172
REMOVAL
Refer to IP-22, "Removal and Installation".
DISASSEMBLY
Removal and InstallationINFOID:0000000003940173
REMOVAL
1. Remove console finisher. Refer to IP-22, "Removal and Installation".
2. Remove auxiliary mounting screws.
3. Remove auxiliary input jacks.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1048ZZ
1. Auxiliary input jacks

AV-180
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
CAMERA CONTROL UNIT
CAMERA CONTROL UNIT
Exploded ViewINFOID:0000000003940174
Removal and InstallationINFOID:0000000003940175
REMOVAL
1. Remove rear wheelhouse finisher RH. Refer to INT-57, "Removal and Installation".
2. Remove camera control unit mounting screws, disconnect the camera control unit connector.
3. Remove camera control unit.
INSTALLATION
1. Installation is the reverse order of removal.
2. Perform predicted course line center position adjustment. Refer to AV-47, "
PREDICTED COURSE LINE
CENTER POSITION ADJUSTMENT : Special Repair Requirement".
JPNIA1049ZZ
1. Camera control unit

AV
REAR VIEW CAMERA
AV-181
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
REAR VIEW CAMERA
Exploded ViewINFOID:0000000003940176
DISASSEMBLY
Removal and InstallationINFOID:0000000003940177
REMOVAL
1. Remove trunk lid finisher inner. Refer to INT-59, "Removal and Installation".
2. Remove trunk lid finisher. Refer to EXT-38, "
Removal and Installation".
3. Remove rear view camera mounting clip, disconnect the rear view camera connector.
4. Remove rear view camera.
INSTALLATION
1. Installation is the reverse order of removal.
AdjustmentINFOID:0000000003970920
Adjust the guide line position if the guide line position is shifted after installing the rear view camera.
1. Draw lines on rearward area of the vehicle passing through the
following points: 200 mm (7.87 in) from both sides of the vehicle,
and 0.5 m (1.64 ft), 1.0 m (3.28 ft) from the rear end of the
bumper.
2. Set into “Adjust offset of rear view camera” mode of Confirma-
tion / Adjustment mode.
JPNIA1050ZZ
1. Rear view camera
2. Seal
Refer to GI-4, "
Components" for symbols in the figure.
SKIB3691E

AV-182
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
REAR VIEW CAMERA
3. Rotate the center dial, and then select the guiding line pattern so
that its angle is aligned with the correction line of the rear of the
vehicle.
4. Fine adjust the guiding line so that its position is aligned to the
correction line by pressing the up/down/left/right switches.
Pressing “ENTER” enable the camera control unit to memory
the adjusted guiding line position.
CAUTION:
Never operate other function such as pressing BACK while writing index data.
If Confirmation/Adjustment mode does not function in the above procedure, perform one of the
following service to adjust the index again.
 Remove battery for five min. Then reconnect battery.
 Remove camera control unit connector for five min. Then reconnect camera control unit connec-
tor.Selected pattern : 7
Up/Down adjustment range : −20 – 20
Left/Right adjustment range : −20 – 20
SKIB3689E

AV
STEERING ANGLE SENSOR
AV-183
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
STEERING ANGLE SENSOR
Exploded ViewINFOID:0000000003940179
REMOVAL
Refer to SR-9, "Exploded View".
DISASSEMBLY
Removal and InstallationINFOID:0000000003940180
REMOVAL
1. Remove spiral cable.
2. Remove steering angle sensor mounting screws.
3. Remove steering angle sensor.
INSTALLATION
Installation is the reverse order of removal.
JSNIA0135ZZ
1. Spiral cable
2. Steering angle sensor

AV-184
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
ANTENNA FEEDER (RADIO)
ANTENNA FEEDER (RADIO)
Harness LayoutINFOID:0000000003882826
JPNIA1033GB

AV
DIAGNOSIS AND REPAIR WORKFLOW
AV-185
< BASIC INSPECTION >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work FlowINFOID:0000000003765632
OVERALL SEQUENCE
 Reference 1··· Refer to AV- 2 11 , "CONSULT-III Function (MULTI AV)".
 Reference 2··· Refer to AV-284, "
DTC Index".
 Reference 3··· Refer to AV-372, "
Symptom Table".
DETAILED FLOW
1.INTERVIEW AND SYMPTOM CONFIRMATION
Check the malfunction symptoms by performing the following items.
 Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred).
 Check the symptom.
Is the occurred symptom malfunction?
YES >> GO TO 2.
NO >> INSPECTION END
2.DIAGNOSIS WITH CONSULT-III
JSNIA0732GB

AV-186
< BASIC INSPECTION >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS AND REPAIR WORKFLOW
1. Connect CONSULT-III and perform a self-diagnosis for “MULTI AV”. Refer to AV- 2 11 , "CONSULT-III Func-
tion (MULTI AV)".
NOTE:
Skip to step 4 of the diagnosis procedure if “MULTI AV” is not displayed.
2. Check if any DTC is displayed in the self-diagnosis results.
Is DTC displayed?
YES >> GO TO 3.
NO >> GO TO 4.
3.TROUBLE DIAGNOSIS FOR DTC
1. Check the DTC indicated in the self-diagnosis results.
2. Perform the relevant diagnosis referring to the DTC Index. Refer to AV-284, "
DTC Index".
>> GO TO 5.
4.TROUBLE DIAGNOSIS FOR SYMPTOMS
Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to AV-372, "
Symptom
Table".
>> GO TO 5.
5.ERROR PART REPAIR
1. Repair or replace the identified malfunctioning parts.
2. Perform a self-diagnosis for “MULTI AV” with CONSULT-III.
NOTE:
Erase the stored self-diagnosis results after repairing or replacing the relevant components if any DTC
has been indicated in the self-diagnosis results.
3. Check that the symptom does not occur.
Does the symptom occur?
YES >> GO TO 1.
NO >> INSPECTION END