NISSAN TEANA 2008 Service Manual

VTL-20
< ON-VEHICLE MAINTENANCE >[WITHOUT 7 INCH DISPLAY]
AIR CONDITIONER FILTER
ON-VEHICLE MAINTENANCE
AIR CONDITIONER FILTER
Exploded ViewINFOID:0000000003774654
Removal and InstallationINFOID:0000000003774655
REMOVAL
1. Remove filter cover (1), and then remove air conditioner filter
(2).
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
 If the filter is deformed/damaged when removing, replace it with a new one. Deformed/damaged filter
may deteriorate the duct collecting performance.
 When installing, handle the filter with extreme care to avoid deforming/damaging.
ReplacementINFOID:0000000003774656
Replace air conditioner filter.
Refer to MA-6, "
Periodic Maintenance".
Affix a caution label inside the glove box when replacing filter.
1. Heater & cooling unit assembly 2. Air conditioner filter 3. Filter cover
JPIIA0895ZZ
JPIIA0896ZZ

A/C CONTROL
VTL-21
< ON-VEHICLE REPAIR >[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
ON-VEHICLE REPAIR
A/C CONTROL
Exploded ViewINFOID:0000000003774657
Removal and InstallationINFOID:0000000003774658
REMOVAL
1. Remove cluster lid D. Refer to IP-11, "Exploded View".
2. Remove mounting screws (A), and then remove A/C control (1).
INSTALLATION
Installation is basically the reverse order of removal.
1. Cluster lid D 2. A/C control
JPIIA0948ZZ
JPIIA0949ZZ

VTL-22
< ON-VEHICLE REPAIR >[WITHOUT 7 INCH DISPLAY]
A/C DISPLAY
A/C DISPLAY
Exploded ViewINFOID:0000000003774659
DISASSEMBLY
Removal and InstallationINFOID:0000000003774660
REMOVAL
1. Remove cluster lid D. Refer to IP-11, "Exploded View".
2. Remove mounting screws (A), and then remove audio display
with bracket as a single unit (1).
3. Remove mounting screws (A), and then remove A/C display (1).
INSTALLATION
Installation is basically the reverse order of removal.
1. AV display 2. CRT filter 3. A/C display
4. Bracket
JPNIA1028ZZ
JPIIA0950ZZ
JPIIA0951ZZ

A/C AUTO AMP.
VTL-23
< ON-VEHICLE REPAIR >[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
A/C AUTO AMP.
Exploded ViewINFOID:0000000003845419
DISASSEMBLY
Removal and InstallationINFOID:0000000003774662
REMOVAL
1. Remove audio unit. Refer to AV-37, "Removal and Installation".
2. Remove mounting screws (A), and then remove A/C auto amp.
(1).
INSTALLATION
Installation is basically the reverse order of removal.
1. Audio unit 2. Bracket LH 3. A/C auto amp.
4. Bracket RH
JPNIA1027ZZ
JPIIA0897ZZ

VTL-24
< ON-VEHICLE REPAIR >[WITHOUT 7 INCH DISPLAY]
AMBIENT SENSOR
AMBIENT SENSOR
Exploded ViewINFOID:0000000003774663
Removal and InstallationINFOID:0000000003774664
REMOVAL
1. Remove engine under cover. Refer to EXT-28, "Exploded View".
2. Disconnect ambient sensor connector (A), and then remove
ambient sensor (1).
INSTALLATION
Installation is basically the reverse order of removal.
1. Ambient sensor
JPIIA0898ZZ
JPIIA0899ZZ

IN-VEHICLE SENSOR
VTL-25
< ON-VEHICLE REPAIR >[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
IN-VEHICLE SENSOR
Exploded ViewINFOID:0000000003774665
Removal and InstallationINFOID:0000000003774666
REMOVAL
1. Remove instrument lower panel LH. Refer to IP-11, "Exploded View".
2. Remove mounting screw (A), and then remove in-vehicle sensor
(1).
INSTALLATION
Installation is basically the reverse order of removal.
1. In-vehicle sensor 2. Instrument lower panel LH
JPIIA0902ZZ
JPIIA0903ZZ

VTL-26
< ON-VEHICLE REPAIR >[WITHOUT 7 INCH DISPLAY]
SUNLOAD SENSOR
SUNLOAD SENSOR
Exploded ViewINFOID:0000000003774667
Removal and InstallationINFOID:0000000003774668
REMOVAL
1. Disconnect sunload sensor connector, and then remove sunload
sensor (1).
INSTALLATION
Installation is basically the reverse order of removal.
1. Sunload sensor
JPIIA0904ZZ
JPIIA0905ZZ

INTAKE SENSOR
VTL-27
< ON-VEHICLE REPAIR >[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
INTAKE SENSOR
Exploded ViewINFOID:0000000003821339
1. Ventilator seal 2. Defroster seal 3. Distributor upper case
4. Center case 5. Heater & cooling unit case cover 6. Foot duct 1 (right)
7. Foot duct 2 (right) 8. Air mix door motor (passenger side) 9. Evaporator pipe assembly
10. Expansion valve 11. O-ring 12. Evaporator
13. Filter cover 14. Air conditioner filter 15. Case packing
16. Heater & cooling unit case (right) 17. Cooler pipe grommet 18. Grommet
19. Heater pipe grommet 20. Heater pipe support 21. Drain hose
22. Heater & cooling unit case (left) 23. Air mix door motor (driver side) 24. Heater core
25. Heater pipe cover 26. Foot duct 2 (left) 27. Foot duct 1 (left)
28. Aspirator hose 29. Aspirator 30. Mode door motor
31. Main link 32. Rod link 33. Ventilator door link
34. Mode door lever 35. Ventilator door lever 36. Max. cool door link
JPIIA0906GB

VTL-28
< ON-VEHICLE REPAIR >[WITHOUT 7 INCH DISPLAY]
INTAKE SENSOR
Removal and Installation
INFOID:0000000003774670
REMOVAL
1. Remove evaporator pipe assembly. Refer to HA-54, "Exploded View".
2. Disconnect intake sensor connector.
3. Slide evaporator (1) toward the right side of the vehicle (as
shown in the figure), and then remove intake sensor (2).
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
 Replace O-rings with new ones. Then apply compressor oil to them when installing.
 Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor
can be located in the same position.
 Do not rotate the bracket insertion part when removing and installing the intake sensor.
 Check for refrigerant leakage when charging refrigerant.
37. Defroster door link 38. Foot door link 39. Max. cool door lever
40. Foot door lever 41. Defroster door lever 42. Adapter case
43. Distributor lower case 44. Ventilator door 45. Intake sensor
46. Intake sensor bracket 47. Foot door 48. Max. cool door
49. Defroster door 50. Air mix door (Slide door)
Refer to GI-4, "
Components" for symbols in the figure.
JPIIA0907ZZ

BLOWER UNIT
VTL-29
< ON-VEHICLE REPAIR >[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
BLOWER UNIT
Exploded ViewINFOID:0000000003774671
DISASSEMBLY
1. Blower unit 2. Heater & cooling unit assembly 3. Steering member
4. Instrument stay 5. Instrument panel assembly
Refer to GI-4, "
Components" for symbols in the figure.
JPIIA0914GB