NISSAN TIIDA 2007 Service Repair Manual

REAR WIPER MOTOR CIRCUIT
WW-29
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
1. Turn the ignition switch OFF.
2. Disconnect BCM.
3. Check continuity between rear wiper motor harness connector
(A) and BCM harness connector (B).
Does continuity exist?
YES >> GO TO 4
NO >> Repair or replace harness.
4. CHECK REAR WIPER MOTOR SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES >> Repair or replace harness.
NO >> Replace BCM. Refer to BCS-57, "
Removal and Installa-
tion of BCM".
Rear wiper motor BCM
Continuity
Connector Terminal Connector Terminal
D404 (A) 1 M20 (B) 71 Yes
ALLIA0354ZZ
BCM
GroundContinuity
Connector Terminal
M20 71 No
ALLIA0355ZZ

WW-30
< COMPONENT DIAGNOSIS >
REAR WIPER AUTO STOP SIGNAL CIRCUIT
REAR WIPER AUTO STOP SIGNAL CIRCUIT
Component Function CheckINFOID:0000000001366623
1.CHECK REAR WIPER (AUTO STOP) OPERATION
CONSULT-III DATA MONITOR
1. Select "WIPER" of BCM data monitor item.
2. Operate the rear wiper.
3. Check that "RR WIPER STOP" changes to "ON" and "OFF" linked with the wiper operation.
Is the status of item normal?
YES >> Rear wiper auto stop signal circuit is normal.
NO >> Refer to WW-30, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001366624
1. CHECK REAR WIPER MOTOR (AUTO STOP) OUTPUT VOLTAGE
1. Turn the ignition switch OFF.
2. Disconnect rear wiper motor.
3. Turn the ignition switch ON.
4. Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES >> GO TO 3
NO >> GO TO 2
2. CHECK REAR WIPER MOTOR (AUTO STOP) SHORT CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect BCM.
3. Check continuity between BCM harness connector and ground.
Does continuity exist?
YES >> Repair or replace harness.
NO >> Replace BCM. Refer to BCS-57, "
Removal and Installa-
tion of BCM".
3. CHECK REAR WIPER MOTOR (AUTO STOP) CIRCUIT CONTINUITY
Monitor item Condition Monitor status
RR WIPER STOP Rear wiper motorStop position ON
Except stop position OFF
Te r m i n a l s
Voltage
(Approx.) (+) (−)
BCM
Ground Connector Terminal
M18 23 Battery voltage
ALLIA0356ZZ
BCM
GroundContinuity
Connector Terminal
M18 23 No
ALLIA0357ZZ

REAR WIPER AUTO STOP SIGNAL CIRCUIT
WW-31
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
1. Turn the ignition switch OFF.
2. Disconnect BCM.
3. Check continuity between BCM harness connector and rear
wiper motor harness connector.
Does continuity exist?
YES >> Replace rear wiper motor. Refer to WW-77, "Removal
and Installation".
NO >> Repair or replace harness.
Rear wiper motor BCM
Continuity
Connector Terminal Connector Terminal
D404 (A) 2 M18 (B) 23 Yes
ALLIA0358ZZ

WW-32
< COMPONENT DIAGNOSIS >
HEADLAMP WASHER RELAY
HEADLAMP WASHER RELAY
Component InspectionINFOID:0000000001366625
1. CHECK HEADLAMP WASHER RELAY
1. Turn the ignition switch OFF.
2. Disconnect headlamp washer relay.
3. Apply battery voltage to headlamp washer relay between termi-
nals 1 and 2.
4. Check continuity of headlamp washer relay.
Does continuity exist?
YES >> Headlamp washer relay is normal.
NO >> Replace headlamp washer relay.
Headlamp washer relay Condition
Continuity
Terminal Voltage
35Apply Yes
Not Apply No
SEF145X

HEADLAMP WASHER CIRCUIT
WW-33
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
HEADLAMP WASHER CIRCUIT
Component Function CheckINFOID:0000000001366626
1. CHECK HEADLAMP WASHER OPERATION
CONSULT-III ACTIVE TEST
1. Select "HEAD LAMP WASHER" of IPDM E/R active test item.
2. While operating the test item, check headlamp washer operation.
Is the headlamp washer operation normally?
YES >> Headlamp washer circuit is normal.
NO >> Refer to WW-33, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001366627
1. CHECK HEADLAMP WASHER FUSIBLE LINK
1. Turn the ignition switch OFF.
2. Check that the following fusible link is not blown.
Is the fusible link blown?
YES >> Replace the fusible link after repairing the applicable circuit.
NO >> GO TO 2
2. CHECK HEADLAMP WASHER RELAY POWER SUPPLY
1. Remove headlamp washer relay.
2. Turn the ignition switch ON.
3. Check voltage between headlamp washer relay harness con-
nector and ground.
Is the measurement value normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK HEADLAMP WASHER RELAY
1. Check headlamp washer relay. Refer to WW-32, "
Component Inspection".
Is the headlamp washer relay normal?
YES >> GO TO 4
NO >> Replace the headlamp washer relay.
4. CHECK HEADLAMP WASHER RELAY SIGNAL OUTPUT
CONSULT-III ACTIVE TESTON : Headlamp washer ON operation
OFF : Stop the headlamp washer.
Unit Location Fusible Link No. Capacity
Headlamp washer motor Fuse and fusible link box L 30 A
Te r m i n a l s
Vo l ta g e
(Approx.) (+) (−)
Headlamp washer relay
Ground Connector Terminal
E341
Battery voltage
5
ALLIA0359ZZ

WW-34
< COMPONENT DIAGNOSIS >
HEADLAMP WASHER CIRCUIT
1. Turn the ignition switch OFF.
2. Install headlamp washer relay.
3. Turn the ignition switch ON.
4. Select "HEADLAMP WASHER" of IPDM E/R active test item.
5. While operating the test item, check voltage between IPDM E/R
harness connector and ground.
Is the measurement value normal?
YES >> GO TO 7
Fixed at 0V >> GO TO 5
Fixed at battery voltage >> Replace IPDM E/R. Refer to xxx.
5. CHECK HEADLAMP WASHER RELAY CONTROL SIGNAL OPEN CIRCUIT
1. Remove headlamp washer relay.
2. Disconnect IPDM E/R.
3. Check continuity between headlamp washer relay harness con-
nector (A) and IPDM E/R harness connector (B).
Does continuity exist?
YES >> GO TO 6
NO >> Repair or replace harness.
6. CHECK HEADLAMP WASHER RELAY CONTROL SIGNAL SHORT CIRCUIT
Check continuity between IPDM E/R harness connector and ground.
Does continuity exist?
YES >> Repair or replace harness.
NO >> Replace IPDM E/R. Refer to xxx.
7. CHECK HEADLAMP WASHER PUMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect headlamp washer pump.
3. Remove headlamp washer relay.
4. Check continuity between headlamp washer relay harness con-
nector and headlamp washer pump harness connector.
Te r m i n a l s
Te s t i t e m
Vo l ta g e
(Approx.) (+) (−)
IPDM E/R
GroundHEADLAMP
WASHER
Connector Terminal
E45 25ON 0V
OFF Battery voltage
ALLIA0360ZZ
Headlamp washer relay IPDM E/R
Continuity
Connector Terminal Connector Terminal
E34 (A) 2 E45 (B) 25 Yes
ALLIA0361ZZ
IPDM E/R
GroundContinuity
Connector Terminal
E45 25 No
ALLIA0362ZZ
Headlamp washer relay Headlamp washer pump
Continuity
Connector Terminal Connector Terminal
E34 (A) 3 E35 (B) 1 Yes
ALLIA0363ZZ

HEADLAMP WASHER CIRCUIT
WW-35
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
Does continuity exist?
YES >> GO TO 8
NO >> Repair or replace harness.
8. CHECK HEADLAMP WASHER PUMP SHORT CIRCUIT
Check continuity between headlamp washer pump harness connec-
tor and ground.
Does continuity exist?
YES >> Repair or replace harness.
NO >> GO TO 9
9. CHECK HEADLAMP WASHER PUMP (GROUND) OPEN CIRCUIT
Check continuity between headlamp washer pump harness connec-
tor and ground.
Does continuity exist?
YES >> Replace the headlamp washer pump. Refer to WW-66,
"Removal and Installation".
NO >> Repair or replace harness.
Headlamp washer pump
GroundContinuity
Connector Terminal
E35 1 No
ALLIA0364ZZ
Headlamp washer pump
GroundContinuity
Connector Terminal
E35 2 Yes
ALLIA0365ZZ

WW-36
< COMPONENT DIAGNOSIS >
FRONT WIPER AND WASHER SYSTEM
FRONT WIPER AND WASHER SYSTEM
Wiring DiagramINFOID:0000000001366628
ALLWA0062GB

FRONT WIPER AND WASHER SYSTEM
WW-37
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
ALLIA0607GB

WW-38
< COMPONENT DIAGNOSIS >
FRONT WIPER AND WASHER SYSTEM
ALLIA0608GB