OPEL FRONTERA 1998 Workshop Manual

7A–50 AUTOMATIC TRANSMISSION (AW30-40LE)
DTC P1121 (FLASHING CODE 23) ANALOG THROTTLE SIGNAL FAILURE (VREF, VGND)
D07RY00023Circuit description:
When the signal of the engine throttle position sensor
located on the accelerator pedal is supplied to the
transmission TCM, the TCM judges the opening
condition of the throttle.
The shift point of the transmission is determined by this
opening condition of the throttle.
Fail-safe control:
The TCM controls fail-safe by detecting analog throttle
signal (VREF, VGND) failure.
Failure detection:
• When the Vref input voltage is detected more than
5.55V or less than 4.45V.
• When the Vgnd input voltage is detected more than
0.40V or less than -0.40V.
• When the failure criteria is continuously for 1.0 sec.
Contents of control:
At failure detection
• Judges throttle opening of linear sensor (Vth) as
Vref:5V, Vgnd:0V
• Throttle learning control inhibit
• Up hill and down hill control inhibit
At failure decision
Executes following items in addition to above control
items at failure detection.
• Stores the failure information in failure-memory
Conditions of turning “CHECK TRANS” lamp off:
None
Reversion conditions from fail-safe:
At failure detection
When the Vref input voltage is detected less than 5.55 V
and more than 4.45 V.
When the Vgnd input voltage is detected less than 0.40 V
and more than -0.40 V.
At failure decision
• Recovers when judged 0km/h by output revolutionsensor after the Vref input voltage is detected less
than 5.55V and more than 4.45V.
(however, uses 0 km/h judgment by back-up vehicle
speed at output revolution failure)
• Recovers when judged 0km/h by output revolution
sensor after the Vgnd input voltage is detected less
than 0.40V and more than -0.40V.
(however, uses 0 km/h judgment by back-up vehicle
speed at output revolution failure)
Test description:
The following numbers correspond to circled numbers on
the diagnostic char t.
(1) Check the power supply voltage (4.75-5.25V) of
throttle position sensor.
Diagnostic aids:
An intermittent may be caused by a poor connection,
rubbed through wire insulation or a wire broken inside
the insulation. Inspect related harness connector for
backed out terminals, improper mating, broken locks,
improperly formed or damaged terminals, poor terminal
to wire connection and damaged harness.

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–51
DTC P1121 (FLASHING CODE 23) ANALOG THROTTLE SIGNAL FAILURE (VREF, VGND)
DTCP1121

7A–52 AUTOMATIC TRANSMISSION (AW30-40LE)
WIRING DIAGRAM
D07RY00048

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–53
WIRING DIAGRAM
D07RY00050

7A–54 AUTOMATIC TRANSMISSION (AW30-40LE)
CONNECTOR LIST
No. Connector face No. Connector face
B-14 E-30
B-17 E-31
B-30 E-32
B-35 E-49
C-63 H-4
(BLACK)
C-78 H-5
(GREEN)
C-79H-7
(RHD)
E-1H-7
(LHD)
E-2H-8
(RHD)
E-29H-8
(LHD)

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–55
CONNECTOR LIST
No. Connector face No. Connector face
H-42H-9
(RHD)
I-9H-9
(LHD)
I-10H-12
(RHD)
H-24
(RHD)
H-24
(LHD)
H-25
(LHD)
H-26
(RHD)
H-30
(NATURAL)
H-32

7A–56 AUTOMATIC TRANSMISSION (AW30-40LE)
TROUBLESHOOTING CHART
Number are arranged in order of probability.
Parform inspections starting with number one and working up.

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–57

7A–58 AUTOMATIC TRANSMISSION (AW30-40LE)

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–59