Peugeot Partner Tepee 2015 Owner's Manual

169
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
3. Direction indicators
T

ype B, PY21W - 21W (amber)
-

Remove the cover by pullin
g the
flexible rubber tab.
-
t
urn the bulb holder a quarter
turn anticlockwise.
-


Remove the bulb by pressing
it lightly while turning it
anticlockwise.
-


Change the bulb.
-


Ensure that the cover is refitted
correctly all round to assure
correct sealing.
2.

Sidelamps

T

ype A, W5W - 5W
-

Remove the cover by pullin

g the
flexible rubber tab.
-

Remove the bulb holder fitted by
pressure by pullin

g the connector.
-

Change the bulb.
-


Ensure that the cover is refitted
correctly all round to assure
correct sealing.
FRONT LAMPS
1. Dipped / Main beam headlamps
T

ype C, H4 - 55W
-

Remove the centre cover by
pullin

g the flexible rubber tab.
-

Disconnect the electrical
connector

.
-

Release the retaining tab.
-


Change the bulb taking care
to align the metal part with the
grooves on the lamp.
-


Reposition the retaining tab.
-


Ensure that the cover is refitted
correctly all round to assure
correct sealing.
Changing a bulb
QuICK HeLP
8

170
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
4. Foglamps
T

ype C, H1 - 55W
-

Remove the three clips and the screw
securing the wheelarch liner, located
below the bumper.
- Move the wheelarch liner upwards.- Remove the foglamp by removing the
screw, which can be accessed via the
hole provided for this purpose in the
bumper, using a
torx© 30 screwdriver.- unclip the foglamp by squeezing the
clip to release it.
- Remove the foglamp from the outside.- turn the yellow cover a 1/4 turn to open.- Separate the clips which secure the
base of bulb on each side to release
the bulb.
- Remove the bulb by pulling, keeping it
straight.
- Insert the new bulb, reposition the clips
around the base of the bulb and carry
out the operations in reverse order to
put the lamp unit and the bumper back
in position.
SIDE REPEATER
Type A, WY5W - 5W (amber)
-

Push the repeater towards the rear
and disengage it by pullin

g the
front.
-

Contact a P
euge O t
dealer to
obtain a new repeater which is a
sealed component.
-


T
o refit, engage the repeater
towards the rear and bring it
towards the front.
COURTESY LAMPS
Type A, 12V5W - 5W
-
u nclip the lens by sliding a
screwdriver in the slots on each
side of the courtesy lamp.
-

Pull the bulb out and change it.
-


Clip the lens in its housing and
ensure that it is secured correctly

.
Front / Rear
Changing a bulb

171
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
REAR LAMPS
this procedure requires the use of
the spanner supplied with the tools for
changing a wheel.
When refitting, take care to
reposition the tabs and the supply
wire correctly to avoid trapping the
wire.
After changing the rear direction
indicator bulb, the reinitialisation time is
above 2 minutes. - Move aside the 4 tabs then extract
the bulb holder
.
-

Remove the faulty bulb by
pressing it lightly while turning it
anticlockwise.
-


Change the bulb.
When removing the lamp unit:
-


with tailgate, pull the lamp unit
towards the centre of the vehicle,
-


with hinged doors, pull the lamp
unit towards you.
For more information concerning the
bulbs, refer to the "

types of bulb".
1.

Brake lamps / sidelamps




T

ype B, P21/5W - 21/5W
2.

Direction indicators




T

ype B, PY21W - 21W (amber)
3.

Reversing lamps




T

ype B, P21W - 21W
4.

Foglamps




T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the other lamps
and their edges to avoid damaging
their coating and seals. Chapter 9, "Changing a wheel"
section.
-

Identify the faulty bulb, then open
the rear doors to 180°. Chapter 3, "Access" section.
-


Remove the two fixing bolts using
the spanner provided.
-


Pull the lamp unit from the outside.
-


Holding the lamp, disconnect the
electrical connector

.
Changing a bulb
QuICK HeLP
8

172
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
NUMBER PLATE LAMPS
- unscrew the two nuts.
-
Push the pins.
-


If necessary
, disconnect the
connector to remove the lamp.
-

Change the bulb.
W

ith tailgate
-

Disengage the plastic lens using a
screwdriver

.
-

Change the bulb.
-


Replace the plastic lens and press
on it.
THIRD BRAKE LAMP
Type A, W16W - 16W
With hinged doors
-
u
nclip the interior trim.
-

Disconnect the connector by
moving aside its tab.
-

t
urn the bulb holder a quarter turn
anticlockwise.
-


Change the bulb.
-


Put the bulb holder back in place
and reconnect the connector

.
-

Put the trim back in place.
T

ype A, W5W - 5W
Changing a bulb

173
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
CHANGING A FUSE
the fuseboxes are located:
-
in the lower dashboard on the left-
hand side (behind the cover),
-


under the bonnet (near the battery).
t

he information given concerns only
those fuses which can be changed by
the user using the tweezer, located
behind the dashboard storage
compartment on the right-hand side.
For any other work, visit a P
euge O t

dealer or a qualified workshop.
Removing and fitting a fuse
Always replace a failed fuse with a
fuse of the same rating.
Motor trade technicians: for
complete information on the fuses
and relays, refer to the "Repair
Manual" diagrams via the dealer
network.
P
euge
O
t will not accept
responsibility for the cost incurred in
repairing your vehicle or for rectifying
the malfunctions resulting from
the installation of accessories not
supplied and not recommended by the
P
euge
O
t
network and not installed
in accordance with its instructions,
in particular when the combined
consumption of all of the additional
equipment connected exceeds


10 milliamperes. Before replacing a fuse, the cause of
the incident must be identified and
rectified.
●

Use the tweezer

.
Changing a fuse
QuICK HeLP
8

174
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
DASHBOARD FUSES
tilt the cover to gain access to the
fuses. Fuses
FAmperes
A Allocation
1 15 Rear wiper
2 - Spare
3 5 Airbag
4 10 Air conditioning, diagnostic socket, mirror control,
headlamp beam
5 30
e

lectric windows
6 30 Locks
7 5Rear courtesy lamp, front map reading lamp, roof
console
8 20 Audio equipment, screen, tyre under-inflation
detection, alarm and siren
9 30 Front and rear 12V socket
10 15 Central column 11 15 Low current ignition switch
12 15 Rain and sunshine sensor, airbag
13 5 Instrument panel
14 15 Parking sensors, digital air conditioning controls,
hands-free phone kit
15 30 Locks
16 - Spare
17 40 Rear screen/mirrors demist/defrost
Changing a fuse

175
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
PASSENGER COMPARTMENT FUSES
Fuses F Amperes
A Allocation
1 - Spare
2 20 Heated seats
3 - Spare
4 15 Folding mirrors relay
5 15 Refrigeration equipment socket relay
Changing a fuse
QuICK HeLP
8

176
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
FUSES UNDER THE BONNET
After opening the bonnet, unclip and tilt
the corresponding box to gain access
to the fuses.Fuses
F Amperes
A Allocation
1 20
e
ngine management
2 15 Horn
3 10 Front and rear wash-wipe pump
4 20 Headlamp wash pump
5 15
e

ngine components
6 10 Steering wheel angle sensor, DSC
7 10 Brake switch, clutch switch
8 25 Starter
9 10 Headlamp beam motor, parc management
unit
10 30
e

ngine components
11 40 Spare
12 30 Wipers
13 40 Built-in systems interface
14 30 Pump
15 10 Right-hand main beam headlamp
16 10 Left-hand main beam headlamp
17 15 Right-hand dipped beam headlamp
18 15 Left-hand dipped beam headlamp
Changing a fuse

177
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
Placing the windscreen wiper
blades in the special position
- Less than a minute after switching
off the ignition, press the wiper stalk
downwards to position the wiper
blades along the windscreen pillars
(special position). Changing a front wiper blade
-

Lift the wiper arm.
-
u nclip the blade and remove it.
- Fit the new blade.
-

Push back the wiper arm.
to return the windscreen wipers to
their normal position, switch on the
ignition and operate the wiper stalk. Changing the rear wiper blade
-


Lift the wiper arm, then unclip the
blade and remove it.
-
Fit the new blade and push back
the wiper arm.
CHANGING A WIPER BLADE
Changing a wiper blade
QuICK HeLP
8

178
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
Without lifting (4 wheels on
the road)
You should always use a towing bar.
BEING TOWED
ths procedure involves the use of the
towing eye supplied with the tools for
changing a wheel.
From the front
- unclip the cover by pressing the
bottom part.
-

Fully screw in the removable towing
eye.
From the rear
- unclip the cover using a coin or the
flat part of the towing eye,
-

Fully screw in the removable towing
eye. When towing with the engine
switched of

f, there is no braking or
steering assistance.
Lifting (only 2 wheels on
the road)
It is preferable to raise the vehicle
using professional lifting equipment.
Vehicles fitted with a manual
gearbox (Diesel version)
In the case of vehicles fitted with
a manual gearbox, the gear lever
must be in neutral, failure to observe
this special condition may result in
damage to transmission and braking
components and the absence of
braking assistance when the engine is
started again.
Chapter 9, "Changing a wheel"
section.
Having your vehicle towed