RENAULT KANGOO 1997 KC / 1.G Engine And Peripherals Manual PDF

FUEL MIXTURE
Specifications
12
DESCRIPTIONMAKE/TYPESPECIAL NOTES
Throttle bodyPIERBURG
714 227diameter 41 mm
Idle speed regulation stepping
motor- Voltage: 12 V (at high frequency)
Resistance : tracks A-D52 ± 5 Ω
tracks B-C52 ± 5 Ω
Throttle position
potentiometer
-Voltage: 5 V
Resistance :
Fuel vapour rebreathing
canister
Solenoid valve
DELCO REMYVoltage:12 Volts
Resistance :35 ± 5 Ω
Heated oxygen sensor NGK Voltage at 850 °C
Rich mixture > 625 mvolts
Lean mixture : 0 to 80 mvolts
Heating resistance, tracks A-B : 3 to 15 Ω
Tightening torque : 4.5 daN.m
Diagnostic function
FICHE n° 27
CODE D13
SELECTOR S8
Throttle potentiometer:
Regulated idle speed :16 ≤ # 17 ≤50
Full load :185 ≤ # 17 ≤243
Idle speed R.C.O. :2 % ≤ # 12 ≤15 %
Adaptive idle speed R.C.O. :- 2.4% ≤ # 21 ≤+6.2 %
Adaptive richness operation
:64 ≤ # 30 ≤192
Adaptive idle speed richness :64 ≤ # 31 ≤192
Track no load full load
1-2
1-3
2-35440 Ω
4500 Ω
2160 Ω2200 Ω
4460 Ω
5340 Ω
E7J engine
12-6

FUEL MIXTURE
Throttle body
12D7F engine
Throttle body mounting bolt on
inlet manifold 1
Throttle body stiffening bracket
mounting bolt on cylinder head 1
TIGHTENING TORQUES (in daN.m)
There are no special notes for removal - refitting.
12-7

FUEL MIXTURE
Throttle body
12
Throttle body mounting bolt 1
TIGHTENING TORQUES (in daN.m)
REMOVAL
Disconnect the battery.
Remove the air filter.
Remove the air intake pipe (1).
Disconnect:
- the accelerator cable,
- the connectors :
• of the stepping motor (2),
• of the throttle potentiometer (3).
E7J engine
Remove the four throttle body mounting bolts (5)
and remove the throttle body.
REFITTING
Replace the throttle body seal.
Refitting is then the reverse of removal.
13339R113338R
12-8

FUEL MIXTURE
Inlet manifold
12D7F engine
TIGHTENING TORQUES (in daN.m)
There are no special notes for removal - refitting
TIGHTENING TORQUES (in daN.m)
Injector gallery mounting bolt on manifold 1
Manifold mounting nut on cylinder head 1.7
Manifold mounting stud on cylinder head 1
12-9

FUEL MIXTURE
Inlet manifold
12
Inlet manifold bolt and nut 2
TIGHTENING TORQUES (in daN.m)
REMOVAL
Remove:
- the air filter,
- the injector gallery (see section 13).
Lift the vehicle.
Remove the strut (1) (to gain access to the bolt
fixing the strut on the right-hand side of the vehi-
cle, remove the mudguard and the right-hand
wheel).
E7J engine
13339R2
Disconnect the accelerator cable and the electrical
connectors (2) connected to the throttle body.
Remove the bolts and nuts (3) securing the mani-
fold. Lower the vehicle.
Remove the air intake pipe (A) connecting the
throttle body to the air filter.
13335-1R
13130R
12-10

FUEL MIXTURE
Inlet manifold
12
Remove the two bolts (4) mounting the retaining
bracket on the cylinder block. E7J engine
13338R1
Extract the manifold.
REFITTING
Replace the inlet manifold gaskets.
Refitting is then the reverse of removal.
12-11

FUEL MIXTURE
Exhaust manifold
12D7F engine
Manifold mounting nut 2.5
Manifold mounting stud 1
Exhaust downpipe mounting bolt 2.2
TIGHTENING TORQUES (in daN.m)
There are no special notes for the removal - refitting.
12-12

FUEL MIXTURE
Exhaust manifold
12
Manifold mounting bolt 2
TIGHTENING TORQUES (in daN.m)
REMOVAL
Remove the multifunction support (1) (see section
10).
Disconnect the exhaust manifold / exhaust link
(2).
Remove the heat shield (3).
Remove the exhaust manifold. E7J engine
13239R2
REFITTING
Replace the manifold gasket.
Refitting is then the reverse of removal.
12-13

FUEL MIXTURE
Inlet/Exhaust manifolds
12F8Q engine
Manifold mounting studs on cylinder head 1
Manifold mounting nuts on cylinder head 2.7
Inlet manifold strut mounting bolt 2.5
Cylinder block strut mounting bolt 2.5
TIGHTENING TORQUES (in daN.m)
REMOVAL
Remove the air filter (two mounting bolts at the
top, two mounting nuts at the bottom (1)).
Remove, from above, the two nuts fixing the ex-
haust downpipe to the manifold.
Slacken, without removing it, the nut on the
clamp connecting the downpipe to the exhaust
pipe.
Tilt the exhaust downpipe towards the gearbox.
Remove the nuts securing the manifolds:
- nuts (A) from above,
- nuts (B) from below.
PRO12.1
Special note
To remove nut (C) located above the starter mo-
tor, use a small ratchet (6.35 mm square) and a
universal joint.
13047-1R1
13047R
12-14

FUEL MIXTURE
Inlet/exhaust manifolds
12F8Q engine
REFITTING
Replace the manifold gaskets (metal part of the
gasket on the manifold side).
Replace the gaskets between the inlet manifold
and the air filter.
Replace the steel gasket between the exhaust ma-
nifold and the exhaust downpipe.
For the other operations, refitting is the reverse of
removal.
12-15