TOYOTA LAND CRUISER 1998 Factory Repair Manual

Add mode: Response of whether or not being moved to each mode is given with
the number of times of door lock working (lock/unlock).
Within 3 sec.
Within 40 sec.
Within 3 sec.
Rewrite mode:

Confirmation mode:

Prohibition mode:once*1
twice*1
The number of times equivalent to the number
of currently registered codes*2
5 times*1
HINT: The confirmation mode and the prohibition mode are finished
after the responses.
Transmitter SW Operation:
Press both lock and unlock SW. (Between 1 and 1.5 sec.)
Press any one of SW. (For more than 1 sec.)
Response of whether or not the registration is completed is given in the
form of the number of times of door lock operations (lock/unlock opera-
tion).
Register other transmitters?
or
Finish the registration?
Finish the registration.
Within 3 sec.Confirmation mode
Prohibition mode
END Add mode,
Rewrite mode
When registration is completed:
When registration is not completed:once*1
twice*1

Insert the key into the IG key cylinder. Perform one of the following operations to finish the Add mode and the
Rewrite mode.

Open any one of the doors.

Wait for 40 sec. after the code registration.
HINT: In case of registering 4 codes at a time, the mode will be finished
when the 4
th code is registered. Continue
the registration.
Within 40 sec. BE-96
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2469 Author
: Date
:
2004 LAND CRUISER (RM1071U)

Door Lock MotorLOCK
UNLOCK *1:
Door Lock MotorLOCK
UNLOCK *2:1 Sec.
1 Sec.
2 Sec.2 Sec.
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE-97
2470 Author
: Date
:
2004 LAND CRUISER (RM1071U)
HINT:
Operation cycle of the door lock (lock/unlock operation)

I26371
BE23K-02
I04155
O-Ring
I04156
Terminal
BE-104
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2477 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REPLACEMENT
REPLACE TRANSMITTER (LITHIUM) BATTERY
NOTICE:
Special caution should be taken for handling each compo-
nent as they are precision electronic components.
(a) Using a screwdriver, remove the screw and cover.
NOTICE:
Do not pry out the cover forcibly.
HINT:
Push the cover with a finger as shown in the illustration, so that
there becomes clearance, then pry out the cover from that
clearance.
(b) Remove the transmitter.
(c) Using a screwdriver, remove the 2 screws and cover.
(d) Remove the battery (lithium battery).
NOTICE:

Do not push the terminals with a finger.

If prying up the battery (lithium battery) forcibly to re-
move, the terminals are deformed.
(e) Install a battery (lithium battery) as shown in the illustra-
tion.
NOTICE:
Face the battery upward. Take care not to deform the termi-
nals.
(f) Check that O-ring is not distorted or slipped off, and
install the cover.
(g) Using a screwdriver, tighten the 2 screws.
NOTICE:
When the shrews are tightened loosely, it might cause
faulty contact of battery (lithium battery) and terminals.
(h) Assemble the transmitter to the key plate and the cover.
(i) Using a screwdriver, tighten the screw.

BO1KA-02
H06468
Back Door Glass

Spacer
Back Window Outside Moulding
Center Back Door Garnish
Back Door Garnish
Assist Grip
Assist Grip Plug
Inside Handle Bezel
Rear Wiper Arm
Clip

Spacer
Clip
5.4 (55, 48 in.´lbf): Specified torqueN´m (kgf´cm, ft´lbf)

Non-reusable part
- BODYBACK DOOR GLASS
BO-65
2639 Author
: Date
:
2004 LAND CRUISER (RM1071U)
BACK DOOR GLASS
COMPONENTS

BO21C-02
BO4420
Adhesive
BO5231
H04494
a
b
A
B
C
DE
F
GH
a
b BO-68
- BODYBACK DOOR GLASS
2642 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSTALLATION
1. CLEAN AND SHAPE CONTACT SURFACE OF DOOR
PANEL
(a) Using a knife, cut away any rough areas on the door pan-
el.
HINT:
Leave as much of the adhesive on the door panel as possible.
(b) Clean the cutting surface of the adhesive with a piece of
shop rag saturated in cleaner.
HINT:
Even if all the adhesive has been removed, clean the door pan-
el.
2. CLEAN REMOVED GLASS
(a) Remove the damaged clips and spacers.
(b) Using a scraper, remove the adhesive sticking to the
glass.
(c) Clean the glass with cleaner.
NOTICE:
Do not touch the glass after cleaning it.
3. INSTALL NEW CLIPS AND SPACERS
Install new clips and spacers onto the glass as shown in the il-
lustration.
A: 24.3 mm (0.957 in.)
B: 18.6 mm (0.732 in.)
C: 33.1 mm (1.303 in.)
D: 52.8 mm (2.079 in.)
E: 14.4 mm (0.567 in.)
F: 18.0 mm (0.709 in.)
G: 156.6 mm (6.165 in.)
H: 176.8 mm (6.961 in.)

H04079
H02865
Primer M
Primer M
Adhesive
H04080
a
a
a-a
Primer G
- BODYBACK DOOR GLASS
BO-69
2643 Author
: Date
:
2004 LAND CRUISER (RM1071U)
4. INSTALL BACK WINDOW MOULDING
Install a new back window moulding as shown in the illustration.
NOTICE:
Do not touch the glass face after cleaning it.
5. COAT CONTACT SURFACE OF DOOR PANEL WITH
PRIMER ºMº
Using a brush, coat Primer M to the exposed part of door panel
on the vehicle side.
NOTICE:

Let the primer coating dry for 3 minutes or more.

Do not coat Primer M to the adhesive.

Do not keep any of the opened Primer M for later use.
6. COAT CONTACT SURFACE OF GLASS WITH PRIMER
ºGº
(a) Using a brush or sponge, coat the edge of the glass and
contact surface with Primer G.
(b) When the primer coated wrongly to the area other than
the specified, wipe it off with a clean shop rag before the
primer dries.
NOTICE:

Let the primer coating dry for 3 minutes or more.

Do not keep any of the opened Primer G for later use.

H04081
a
A
B a
a-a
H04848
: 10 Clips BO-70
- BODYBACK DOOR GLASS
2644 Author
: Date
:
2004 LAND CRUISER (RM1071U)
7. APPLY ADHESIVE
(a) Cut off the tip of the cartridge nozzle.
HINT:
After cutting off the tip, use all adhesive within the time de-
scribed in the table below.
TemperatureTackfree time
35 °C (95 °F)15 minutes
20 °C (68 °F)100 minutes
5 °C (41 °F)8 hours
(b) Load the cartridge into the sealer gun.
(c) Coat the glass with adhesive, as shown in the illustration.
A: 8.0 mm (0.315 in.)
B: 12.0 mm (0.472 in.)
8. INSTALL BACK DOOR GLASS
(a) Install the glass to the body.
(b) Hold back window glass in place securely with protective
tape or equivalent until the adhesive hardens.
NOTICE:
Take care not to drive the vehicle during the time described
in the table below.
TemperatureMinimum time prior to moving a car
35 °C (95 °F)1.5 hours
20 °C (68 °F)5 hours
5 °C (41 °F)24 hours
9. INSPECT FOR LEAKS AND REPAIR
(a) Conduct a leak test after the hardening time has elapsed.
(b) Seal any leak with sealant.
Part No. 08833-00030 or equivalent.
10. INSTALL REAR WIPER ARM (See page BO-42)
11. INSTALL BACK DOOR GARNISH

H04847
ab
a - a
b - b
ab : 9 Clips
- BODYBACK DOOR GLASS
BO-71
2645 Author
: Date
:
2004 LAND CRUISER (RM1071U)
12. INSTALL CENTER BACK DOOR GARNISH
13. INSTALL INSIDE HANDLE BEZEL
14. INSTALL ASSIST GRIP
Install the assist grip with the 2 screws, then install 2 assist grip
plugs.

BO21B-01
H04847
: 9 Clips
ba
a - a
b - b
ab
H04848
: 10 Clips
H04076
BO-66
- BODYBACK DOOR GLASS
2640 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE ASSIST GRIP
(a) Using a screwdriver, remove the 2 assist grip plugs.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 2 screws and assist grip.
2. REMOVE INSIDE HANDLE BEZEL
3. REMOVE CENTER BACK DOOR GARNISH
Using a screwdriver, remove the center back door garnish.
HINT:
Tape the screwdriver tip before use.
4. REMOVE BACK DOOR GARNISH
Using a screwdriver, remove the back door garnish.
HINT:
Tape the screwdriver tip before use.
5. REMOVE REAR WIPER ARM (See page BO-38)
6. REMOVE OUTSIDE BACK WINDOW MOULDING
Using a knife, cut off the moulding as shown in the illustration.
NOTICE:
Do not damage the body with the knife.

BO5232
H04077
Protective Tape
- BODYBACK DOOR GLASS
BO-67
2641 Author
: Date
:
2004 LAND CRUISER (RM1071U)
7. REMOVE BACK DOOR GLASS
(a) Disconnect the connector.
(b) Push piano wire through between the body and glass
from the interior.
(c) Tie both wire ends to wooden blocks or similar objects.
HINT:
Apply protective tape to the outer surface to keep the surface
from being scratched.
NOTICE:
When separating the glass, take care not to damage the
paint and exterior ornaments.
(d) Cut the adhesive by pulling the piano wire around it.
(e) Remove the glass.
NOTICE:
Leave as much of the adhesive on the body as possible
when cutting off the glass.