TOYOTA LAND CRUISER 1998 Factory Repair Manual

BO1KX-02
- BODYFRONT SEAT
BO-1 17
2691 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSTALLATION
Installation is in the reverse order of removal (See page BO-105).

BO4J3-01
H18929
H04785
H04468
H21292
BO-1 14
- BODYFRONT SEAT
2688 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REASSEMBLY
1. Driver 's Side:
INSTALL SEAT POSITION SENSOR
Install the seat position sensor with a new bolt, then connect the
connector.
Part No.:
Bolt: 90119-06871
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
2. INSTALL SEAT POSITION CONTROL RELAY
Install the seat position control relay with the 2 bolts, then con-
nect the connectors.
Torque: 5.5 N´m (56 kgf´cm, 49 in.´lbf)
3. INSTALL SEATBACK COVER
Install the seatback cover to the seatback pad with new hog
rings.
4. INSTALL LUMBER SUPPORT
Install the lumber support and the spacer with the 2 bolts.
5. w/o Side Airbag:
INSTALL SEATBACK FRAME
(a) Install the seatback cover to the seatback frame.
(b) Install new hog rings.
(c) Install the 2 headrest supports.

H20961
H21294
H19941
H21291
H20959
- BODYFRONT SEAT
BO-1 15
2689 Author
: Date
:
2004 LAND CRUISER (RM1071U)
6. w/ Side Airbag:
INSTALL SEATBACK FRAME
(a) Install the seatback cover to the seatback frame.
(b) Install new hog rings, the clamps and the 2 bolts.
Torque: 4.7 N´m (48 kgf´cm, 42 in.´lbf)
(c) Install the 2 headrest supports.
7. INSTALL SEATBACK ASSEMBLY
(a) w/o Side Airbag:
Install the RH reclining adjuster inside shield with a screw.
(b) w/ Side Airbag:
Place the airbag connector along the inner seat adjuster,
and then install the RH reclining adjuster inside shield
with a screw so that the connector is placed in between.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(c) Install the LH reclining adjuster inside shield with a screw.
(d) Install the seatback assembly with the 4 bolts.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(e) Install new hog rings.
(f) Hang the hook.
(g) Connect the connectors.
8. INSTALL ARMREST
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
9. INSTALL HEADREST
10. INSTALL SEAT CUSHION COVER (See page BO-1 10)
11. INSTALL SEAT CUSHION FRAME
(a) Install the seat cushion frame with new hog rings to the
seat cushion cover with pad.
(b) Hang the hook.
12. INSTALL SEAT CUSHION ASSEMBLY
(a) Install the seat cushion assembly with the 4 bolts to the
seat adjuster.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(b) Engage the wire harness clamp.

H04738
H04737
H03736
H03735
H03733
BO-1 16
- BODYFRONT SEAT
2690 Author
: Date
:
2004 LAND CRUISER (RM1071U)
13. INSTALL FRONT SEAT CUSHION SHIELD
Install the seat cushion shield with the screw.
14. INSTALL LOWER SEAT CUSHION SHIELD
Install the seat cushion shield with the screw.
15. INSTALL SEAT CUSHION INNER SHIELD
Install the seat cushion inner shield with the 3 screws.
16. INSTALL FRONT SEAT INNER BELT
(a) Engage the clamp, then connect the connector.
(b) Install the inner belt with the bolt.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
17. INSTALL SEAT CUSHION OUTER SHIELD
(a) Install the power seat switch with the 3 screws.
(b) Install the lumber support switch with the 2 screws.
(c) Connect the connectors as shown in the illustration.
(d) Install the seat cushion outer shield with the 4 screws.
(e) Install the power seat switch knobs.
18. INSTALL SEATBACK BOARD

BO1KU-04
- BODYFRONT SEAT
BO-105
2679 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE SEAT TRACK OUTER COVERS
Using a screwdriver, remove the 4 seat track outer covers.
HINT:
Tape up the screwdriver tip before use.
2. REMOVE FRONT SEAT
(a) Remove the 4 bolts.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
(b) Disconnect the connectors, then remove the front seat.
NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.

Be careful not to damage the body.

BO4J2-01
H13373
H13388
H13374
H13381
BO-1 10
- BODYFRONT SEAT
2684 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REPLACEMENT
HINT:

Following is the seat heater replacement procedure.

Care should be taken during operation to protect the seat
cover from scratches, dirt or accidental cut of thread.
1. Seat cushion cover:
REMOVE SEAT HEATER
(a) Remove the hog rings.
(b) Remove the seat cushion cover from the pad.
(c) Turn the seat cushion cover inside out.
(d) Disconnect the seat wires.
(e) Remove the tack pins which are fastened to the heater.
(f) Remove the seat heater from the seat cushion cover.
2. Seatback cover:
REMOVE SEAT HEATER
(a) Remove the hog rings and the wires.
(b) Remove the seatback cover from the pad.
(c) Turn the seatback cover inside out.

H13389
H13374
- BODYFRONT SEAT
BO-1 11
2685 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(d) Disconnect the seat wires.
(e) Remove the tack pins which are fastened to the seat heat-
er.
(f) Remove the seat heater from the seatback cover.
3. INSTALL SEAT HEATER TO SEAT COVER
Using a tacker, install a new seat heater to the seat cushion cov-
er with tack pins.
Tacker: BANZAI 303XT or equivalent
NOTICE:
Do not substitute other metal parts for the of tack pins. In-
sufficient distance between the heater and the cover may
result in damage to the heater.

Seat Heater
H20974
Seatback Cover:
Seat Cushion Cover:Tack Pin
Seat HeaterV SlitSeam
A :
B :
Seat Heater
Tack Pin
Tack Pin Seam
V Slit
V Slit
AB
CAA AB
B
AA B
B
B
B
B
B
C
C
C
C
CCC C C C C
B
B
B
B
BBB
BB
BB
B
B
B
B
C :
BO-1 12
- BODYFRONT SEAT
2686 Author
: Date
:
2004 LAND CRUISER (RM1071U)
HINT:

Illustration ºAº and ºBº:
Fasten the cover and the heater with the tack pins match-
ing the seam with the V slit of the heater.

Illustration ºCº:
Fasten the out-stretch cloth pad and the heater with the
tack pins matching the edge of the cloth pad with the V slit
of the heater.

Sewing thread can be substituted for the tack pins. How-
ever, allow a distance of 6 - 7 mm (0.24 - 0.28 in.) be-
tween both sewed parts of the heater and the cover.

H13373
H13381
- BODYFRONT SEAT
BO-1 13
2687 Author
: Date
:
2004 LAND CRUISER (RM1071U)
4. INSTALL SEAT CUSHION COVER TO SEAT CUSHION
PA D
(a) Thread the wires through the listing pocket.
(b) Install the seat cushion cover with new hog rings.
(c) Turn the seat cushion cover inside out to put it back to its
original position.
5. INSTALL SEATBACK COVER TO PAD
(a) Thread the wires though the listing pocket.
(b) Turn the seatback cover inside out to put it back to its origi-
nal position.
(c) Install the seatback cover to pad with new hog rings.

BO1JU-03
BE3367
2 - 2.5 mm
(0.024 - 0.026 in.)0.6 - 0.65 mm(0.079 - 0.098 in.)
- BODYFRONT WIPER AND WASHER
BO-35
2609 Author
: Date
:
2004 LAND CRUISER (RM1071U)
ADJUSTMENT
ADJUST WASHER NOZZLE
Using a tool like the one shown in the illustration, change the
direction of the nozzle hole to adjust the point where washer
fluid hits the windshield.