engine AUDI A5 COUPE 2013 Workshop Manual

186 Intelligent technology
ESC includes and/or works together with the
anti-lock brake system (ABS), brake assist sys ­
tem, anti-slip regulation (ASR) , e lectronic dif­
ferential lock (EDL), dynamic steering" and
e lectronic interaxle differentia l lock* /selective
wheel torque control* . ESC is switched on all
the t ime. I n certa in s ituations whe n you need
l ess t raction, you can switch
off ASR by p ress­
i ng the bu tto n
[ru ¢ page 187, fig. 161 or
¢ page 187, fig. 162. Be sure to sw itch ASR
on aga in when yo u no longer need less t rac­
tion .
Anti -lock braking system (ABS)
ABS prevents the wheels from locking up
when braki ng. The veh icle can still be steered
even d uring h ard br aking. Apply ste ady p res ­
sure to the brake pedal. Do no t pump the ped­
a l. A pulsing in the brake peda l indicates t hat
the system is he lping yo u to b rake the vehicle .
Brake assist system
The brake assis t system can decrease b ra ki ng
d ista nce. It incre ases braking power w hen the
d river p resses the brake pedal q uic kl y in eme r­
gency situations . You must p ress and hold the
b rake peda l until the situation is over. In
vehicles w ith adapt ive cru ise contro l", the
brake assist system is more sensit ive if the
d ista nce detected to t he vehicle a head is too
small.
Anti-slip regulation (ASR)
ASR reduces engine power when the drive
wheels begin to spin and adapts the fo rce to
the road condit ions. This makes it eas ier to
start , accelerate and drive up hills.
Electronic differenti al lock (EDL )
The ED L brakes wheels that are spinn ing and
transfers the drive power to the other drive
wheel or whee ls if t he vehicle is equipped with
all-w heel drive*. This function is available up
to abo ut 60 mph (100 km/h).
In extreme cases, EDL automat ica lly switches
off to help keep the bra ke on the braked whee l
from overheating. EDL wi ll switch on again au-tomat
ica lly when conditions have ret urned to
no rma l.
Dynamic steering*
On vehicles wi th dynam ic steering*, ESC he lps
st abiliz e the steer ing in cr itical situ ations.
Electronic interaxle differential lock* /
selective wheel torque control*
T he elec troni c int eraxle differentia l lock (front
whee l dr ive) o r th e se lec tive whee l torque
control (all-whee l dr ive) oper ates when dr iv ­
ing t hro ugh curves. The front w heel on the in ­
side of the c urve or both whee ls on the inside
of the c urve are b raked se lectively as needed.
This m inimizes sliding in the front wheels and
allows for more precise driving through
curves . The applicable system may not acti­
vate when dr iving in wet o r snowy cond itions.
A WARNING
- ESC, ABS, ASR, EDL dynam ic steering*
an d the ele ct roni c interaxle differential
lo ck* /se lective whee l torque con trol *
fu nction canno t over come the laws of
p hys ics. Th is is especially important on
slippe ry or wet roads . If the systems be­
g in acting to stabilize yo ur vehicle, you
should immediately change yo ur speed
to match the road and traffic conditions. Do not let the increased safety provided
by these systems tem pt you to ta ke risks.
Doing so will increase the risk of a loss of
veh icle cont ro l, col lision and ser ious per­
sonal injur ies.
- Always ada pt your speed to road, traffi c
a nd wea ther condi tions. The risk of los-
ing con trol of the vehicle increases when
d riving too fast, es pec ia lly through
curves and o n slippe ry or wet roads, an d
when dr iv ing too close to vehicles up
ahead. ESC, ABS, the brake ass ist sys­
tem, ASR, EDL dynam ic steer ing* and the
e lectronic inte raxle differentia l lock*/se­
lec tive whee l to rque control* func tion
cannot prevent collisions.
-

-Always acce lerate with specia l care on
even, smooth surfaces s uch as those that
are wet or covered with ice and snow.
The drive wheels can spin even with
these assistance systems that cannot al­
ways help to reduce the risk of loss of ve­ hicle control.
(0 Tips
- ABS and ASR on ly work correctly when
all four wheels are equ ipped w ith ident i­
ca l tires. Different tire s izes can lead to a
reduct ion i n eng ine power.
- You may hear noises when the systems
described are wo rking .
- If the indicator light D] or m!S (USA
models) ;tiJ (Canada models) appears,
the re may be a malfunct ion
c::> page 19,
~ page 19.
Switching on/off
ESC turns on automatically when you start
the engine .
Fig . 161 Vers ion A: low er c en ter co nsol e, fj. OFF bu t­
to n
Fig. 162 Ve rsio n B: upper ce nte r console,~ OFF bu t­
to n
Intelligen t technolog y 187
Turning off ASR
In some sit uatio ns, it may be useful to switch
ASR
off to a llow the wheels to spin . For exam­
ple:
- Rocking the vehicle to free it when i t is st uck
- Dr iving in deep snow or on loose ground
- Dr iving with snow chains
Qu ick ly press the
I~ O FF I button c::> fig. 161
and c::> fig . 162. The Ii indicator light turns on
and the message
Trac tion control (A SR) : Off.
War ning! R estrict ed stability
appears in the
display .
It i s only possible to turn
off the ASR up to
30 mph (SO km/h) for vehicles wi th front
wheel drive . At about 45 mph (70 km/h) it au ­
tomat ically turns on again .
It is possible to
turn
off the ASR at any speed fo r vehicles with
all wheel drive .
Turning off ESC
Press and hold the I;; OFFI button for three
seconds . The
fl ESC indicator light turns on
and the message
Stabil ization cont rol (ESC ):
o ff . Warni ng ! Re str icted stab ilit y
appea rs in
the d isplay. ASR is also sw itched
off when ESC
i s sw itched off.
Switching on
Press the j ;; O FFI button again . The fi indica­
tor light t urns on and the message
St abi liz a­
t ion control (ESC ): On
appears in the disp lay.
_&. WARNING
- Drive whee ls can sp in and you can lose
contro l of the vehicle more eas ily when
ASR and ESC are switched off, especia lly
when the road is s lippery .
- Switch ASR/ESC
off only when yo ur driv ­
ing skills, traffic and weather conditions
permit.
@ Tips
You cannot sw itch ASR and ESC off when
adaptive cruise control* is working .
-

188 Intelligent technology
Braking
What affects braking efficiency?
New brake pads
During the first 250 miles (400 km), new
b rake pads do not possess their fu ll braking
effect , they have to be "broken in" first¢.&. .
You can compensate for this slightly reduced braking power by push ing harder on the brake
pedal. Avoid heavy braking loads during the
break-in per iod.
Operating condition s and d riv ing hab it s
The brakes on today's automob iles are st ill
subject to wea r, depending largely on operat­
ing conditions and driving habits¢.&. . On
vehicles that are e ither driven mostly in stop­
and-go city traffic or are driven hard, the b rake pads should be checked by your author­
ized Audi dealer more often than specified in
the
Warranty & Maint enan ce booklet . Failure
to have your b rake pads inspected can res ult
in red uced brake pe rformance.
On steep slopes, you shou ld use the brak ing
effect of the engine. This way, you p revent un­
necessa ry wear on the brake system. If yo u
must use yo ur brakes, do not hol d the brakes
down continuously. P ump the brakes at inter ­
va ls.
Operating noise
Noises may occur when braking depending on
the speed, brak ing fo rce and outside condi­
tions such as temperature and humidity.
Effect of water and road salt
In ce rtain situat ions, for example after driving
through water , in heavy ra in, after overn ight
conde nsation or afte r washing your car, the
b rak ing effect can be redu ced by mois ture or
ice on the brake rotors and brake pads . The
brakes must be dried first with a few careful
brake applications .
A t higher speeds and with the w indshield w ip­
ers turned on, the brake pads press against
the brake rotors for a short amount of time .
This occurs at regular intervals witho ut the driver noticing and p
rovides fo r bette r brake
response time under wet conditions .
T he effec tiveness of the brakes can be red uced
when the vehicle is d riven on a sa lt -covered
r oad and the brakes are not used . Likewise,
you clean off accumulated salt coating from brake d iscs and pads with a few cautio us ap­
plicat ions of the brake ¢ .&. .
Corro sio n
The re may be a tendency for di rt to b uild up
on the brake pads and corrosion to form on
the discs if the car is not driven regularly or only fo r short trips w ith litt le use of the
brakes.
If the brakes are not used frequently, o r if cor ­
rosion has formed on the discs, it is advisable
to clean off the pads and d iscs by braking
firmly a few times from a moderately high
speed ¢.&. .
Fault s in the brak e syst e m
If you s hou ld notice a sudden increase i n
brake pedal trave l, then one of the two brake
c ircuits may have failed ¢.&. .
Low brake fluid level
Malfunctions can occ ur in the b ra ke system if
the brake fluid level is too low. The brake fluid
l evel is monitored electronica lly.
Brake booster
T he bra ke booster inc reases the pressure that
you generate wi th the b rake peda l. It works
o n ly when the engine is runn ing .¢ .&.
Brake lining wear status
Brake lining wear may be checked by visual in­
spect ion of the condition of the brake pads
th rough the ope nings in the wheel. If neces­
sary, the wheel may be removed for t his in­
spect ion ¢
page 253, Changing a wheel.
_& WARNING ,____
-New b rake pads don't have the best stop­
p ing power and m ust be "broken-in" dur-
ing the initial 100 to 150 miles (150 to
11>-

200 kilometers) of normal city driving.
You can compensate for this by press ing
the brake pedal more firm ly. This also
applies later when new pads are instal­
led .
- You should perform brak ing maneuvers
for the purpose of clean ing the brake
system only if road cond it ions permit.
Other road users must not be put at r isk -
you may cause an acc ident!
- Before descending a steep grade, reduce
speed and shift transmiss ion into a lowe r
gear or lowe r driving range. Do not ride
the brakes or hold the pedal down too long or too often . This cou ld cause the
brakes to get hot and diminish braking
efficiency.
- Do not "ride the brakes" by resting your
foot on the pedal when yo u do not intend
to brake. Th is may cause the brakes to
overheat, premature wear and increased
stopp ing distance.
- Under certain climat ic and operating
condit ions such as passing through wa­
ter, driving in heavy rain or after wash ing
the vehicle, the effect iveness of the
brakes can be reduced. In winter, ice ca n
a ccumulate on the brake pads, linings,
dis cs and d rums. Carefully apply brakes
f or a test . Brakes will dry and ice coat­
ings will be cleaned off after a few ca re ­
ful brake applications.
- Driv ing fo r an ex tended period of time on
salt-covered roads without using your
brakes can also affect braking efficiency.
Clean off accumulated salt coating from
brake discs and pads w ith a few caref ul
brake applicat ions.
- If you damage the front spoiler, or if you install a different spoiler, be sure the air
flow to the front brakes is not obstruct­
ed . Otherwise the brake system co uld
overheat reducing the effectiveness of
t h e ent ire brake system.
- Failur e of one bra ke c ircuit will impair
t h e braking capability resulting in an in­
cr eased stop ping distan ce. Avoid driv ing
the vehicle and have it towed to t he near-
Int ellig ent technolog y 189
est a uthorized Audi dea ler or q ualified
workshop.
- Never let the ve hicle roll to a stop with
the engine shut off.
- If the brake booster is not working, for
examp le when towing you r vehicle, or
because the brake booster has somehow
been damaged, the bra ke pedal must be
pressed considerably harder to make up
for the lack of booster assistance .
Electro-mechanical
power assist, dynamic
steering
The electro-mechanical power assist helps
the driver when steering.
Power steer ing adapts electronically based on
the ve hicle speed .
Indicator lights and messages
• Steering d efective! Do not driv e vehi cle!
If this indicato r light tur ns on and stays on
and t his message appears, the power steer ing
may have failed .
Do
not continue dr iv ing . See your author ized
Audi dealer or other qualified repair facility
fo r ass istance.
':r,y Dy namic steer ing: System fault! You can
continue driving
If the indicator light turns on and the mes­
sage appears, the steering may be more diffi­
cu lt to move or more sensit ive tha n usual. The
steering wheel may a lso be at an ang le when
dr iv ing straight .
Drive slowly to your a uthorized Audi dea ler or
qualified workshop to have the ma lf u nction
corrected .
'Taj Dynamic steering: init ializing
If this drive r message appears and t he in dica ­
tor light is flashing on the instrumen t panel,
dynamic steering * is being rei nitialized. Once
you start the engine afte r this is finished, the .,..
•
•

190 Intelligent technology
steering wheel will be easy to move. Re­
initia lization might be necessary if the steer­
ing whee l was moved hard to the left and
right while the vehicle was not moving. The
d isplay goes out as soon as in itia lizat ion is
comp lete.
A WARNING
Have the dynamic steering* system ma l­
function repaired as soon as poss ible by an
authori zed A udi dealer or any qualified
workshop -risk of accident!
- If the . or
l:r-ij indicator light on ly stays
on for a short t ime, yo u may continue
drivi ng.
- The dynamic steering * stability systems
are not available in the event of a system
malfunction.
- Fo r additional informat ion on dynamic
stee ring*, refer to ¢
page 109.
Driving with your
quattro ®
Applies to vehicles: with all-wheel drive
With all-wheel drive, all four wheels are driv­
en.
General information
W ith all-whee l drive, power is distribute d to
a ll fo ur whee ls. This happens automat ica lly
d epending on your dr iving sty le and the road
conditions at the t ime. See also¢
page 185 .
A cen ter different ial d istr ib ut es the dr iv ing
power var iably to the front and rear axle. It
wo rks together with se lective whee l torque
control, which activates when driving throug h
curves ¢
page 186. With the sport differen ­
tial*, power distribution to the rear wheels is
variable and can be adjusted with Audi drive se lect ¢
page 109 .
The all-wheel drive concept is designed for
h igh engine power . Your vehicle is exception­
ally powerful and has exce llent dr iving charac ­
terist ics bot h under normal driving conditions and on snow and
ice . Always read and follow
safety precautio ns ¢ &. .
Winter tires
When driving in t he win ter, yo ur vehicle wi th
all-wheel d rive h as an adv antage, eve n w it h
r egular tires. In wi nte r road conditions it may
be advisable to mount winter tires (or all -sea ­
son tires) for improved driveability and brak­
i ng : these tires must be mounted on
all fou r
wheels . See also ¢ page 246, Winter tires.
Tire chains
Where tire chains are mandatory on certain
roads, this no rma lly also app lies to ve hicles
with all-wheel drive¢
page 247, Snow
chains .
Replacing wheels/tires
Vehicles wi th a ll-wheel drive m ust always
have ti res of t he same s ize. A lso avoi d tires
with differe nt t read depths . For detai ls see
page ¢
page 242, New tires and replacing
tires and wheels.
Off-Road dr iving?
You r A ud i does no t have e nough gro und clea r­
ance to be used as an off -road vehicle .
It is
t h e refore best to avoid roug h tracks and u n­
even te rrain as much as possib le . Also refer to
¢ page 193.
A WARNING
Always ad just your dr iv ing to road and traf­
f ic conditions. Do not let the extra safety
afforded by all-wheel drive tempt you into
taking ext ra risks .
-Al though the a ll-wheel drive is ve ry ef­
fective, always remember that braking capacity is lim ited by tire t raction. You
s hould t herefore no t drive at ex cessive
speeds on i cy or slippe ry road surfa ces.
- On wet road surfa ces, be careful not to
d rive too fast because the fr on t whee ls
could begin to slide on top of the water
(aquaplaning) . If thi s should occur, you

will have no warning from a sudden in­
crease in engine speed as with a front­
wheel drive vehicle. A lways drive at
speeds wh ich are suited to the road con­
ditions -risk of crash .
Energy management
Starting ability is optimized
Energy management controls the distribution
of electrical energy and thus optimizes the
availability of electrical energy for starting
the engine.
If a vehicle with a conventional energy system
i s not driven for a long period of time, the bat­
tery is discharged by idling current consumers
(e.g. immobilizer) . In certain circumstances it
can result in there being insufficient energy
avai lab le to start the engine.
I ntelligen t energy management in your vehi­
cle handles the distribution of electrical ener­
gy . Starting ability is marked ly improved and
the life of the battery is extended .
Basically, energy management consists o f
battery diagnosis, idling current manage­
ment
and dynamic energy management.
Battery diagnosis
Batt ery d iagnosis continuously dete rmines
the state of the battery. Sensors determine
battery voltage, battery current and battery
temperature. This determines the current
state of charge and the power of the battery.
Idling current management
I dling current management reduces energy
consumption while the vehicle is stand ing.
With the ignition switched off, it contro ls the
energy supply to the various electrica l compo­
nents . Data from battery diagnosis is consid­
ered.
Depending on the battery's state of charge,
individual consumers are gradually turned off
to prevent excessive discharge of the battery
and thus mainta in start ing capability.
Intelligent technology 191
Dynamic energy management
While the vehicle is being driven, dynamic en­
ergy management distrib utes the energy gen ­
erated according to the needs of the individ u­
al components. It regulates consumption, so
that more e lectrical energy is not being used
than is being generated and ensures an opti­
mal state of charge fo r the battery .
{!) Tips
- But even energy management cannot
negate the limits of physics. Consider
that the power and life of a battery are
limited .
- If start ing ability is threatened, the indi­
cator light(•] appears¢
page 17.
What you should know
The highest priority is given to maintaining
starting capability.
The battery is severe ly taxed in short-distance
driv ing, in city traff ic and during the cold time
of year. Abundant electrical energy is re­
quired, but on ly a little is generated . It is also
c rit ical if the engine is not running and electri­
ca l components are turned on. In this in­
stance ene rgy is be ing consumed but none is
being generated .
It is in precisely these situations that you will
notice energy management actively regulat­
in g the distribution of energy.
Vehicle stands for an extended period
If you do not drive your vehicle over a period
of several days or weeks, electr ical compo ­
nents are gradually cut back or switched off .
T h is reduces energy consumption and main­
tains starting capability over a longer period .
Some of the convenience functions may not
operate, such as the interior lights or the
power seat adjustment. The convenience
functions will be available again when you
switch on the ignition and start the engine.
•
•

192 Intelligent technology
With the engine turned off
If you listen to the radio, for example, with
the engine turned off or use othe r MMI func­
tions, the battery is being discharged .
If sta rting capability is jeopa rdized due to en­
e rgy consumpt ion, the fo llowing warning ap­
pears in the MMI display:
Please start the engine soon or the system
will be turned off.
The warning ind icates that the system will be
turned off automatically after 3 minutes.
If
you wish to continue using the functions, you
have to start the engine.
With the engine running
Although electrical energy is generated when
the vehicle is be ing driven, the battery can be­
come discharged . This happens most ly when
l ittle energy is be ing generated a nd a great
deal consumed and the battery's state of
cha rge is not optimal.
To br ing the energy balance back into equili­
b rium, consumers which require especially
la rge amounts of energy are tempo rarily cut
back or switched off. Heating sys tems in par­
ticular requi re a great dea l of energy . If you
notice, for example , that the heated seats* or
the heated rear window are not heating, they
have been temporar ily cut back or switched
off. These systems will be ava ilable again as
soon as the energy ba lance has been restored.
You will a lso notice that engine idle speed has
been increased slightly. This is norma l and not
a cause for concern . By increasing engine idle
speed the add itional energy required is gener­
ated and the batte ry is charged.

Driving and
environment
The first 1
1000
miles
(11500 km) and
afterwards
New engine
The engine needs to be run-in during the first
1,000 miles (1 ,500 km) .
For the first 600 mile s (1,000
kilometers ):
.,. Do not use full throttle.
.,. Do not d rive at engine speeds that are more
than 2/3 of the max imum permitted RPM .
From 600 to 1,000 miles (1 ,000 to
1,500 kilometers ):
.. Speeds ca n gradually be increased to the
maximum perm iss ible road or eng ine speed .
During and after break-in period
.. Do not rev the eng ine up to h igh speeds
when it is cold. Th is applies whether the
transmission is in N (Neutral) or in gear.
After the break- in peri od
.. Do not exceed maximum eng ine speed un­
der any circumstances .
.. Upshift into the next higher gear before
reaching the red area at the end of the tach­
ometer scale c.>page 10.
During the first few hours of driving, the en­
g ine's internal friction is higher than later
when all the moving parts have been broken
in . How well this break -in process is done de ­
pends to a considerable extent on the way the
vehicle is driven du ring the first 1,000 miles
(1,500 kilome ters).
(D Note
Extremely h igh engine speeds are auto­
mat ica lly reduc ed. However, t hese rpm
lim its are programmed for a n engine well
r u n- in, not a new engine.
Driving and environment 193
@) For the sake of the environment
Do not drive with unnecessarily high en­
g ine speeds -upshifting ear ly saves f uel,
reduces noise and protects the environ­
ment.
New tires
If your vehicle is running on new tires, drive
very carefully for the first 350 miles (500 ki lo­
meters) after fitting.
.&, WARNING
N ew tires tend to be sl ippery and mus t al­
so be "b roken -in" . Be sure to remember
this dur ing the f irst 350 m iles (500 kilo­
meters) . Brake gently . Avoid fo llowing
closely behind other vehicles or other sit­
uations that m ight require sudden, hard
b raking .
Avoid damaging the
vehicle
When you are d rivi ng on poo r roads, or over
cu rbs, steep ramps, etc., make certa in that
low- ly in g parts s uch as spo ile rs and ex ha ust
system parts do not bottom o ut and get dam ­
aged.
Th is is espec ially true for veh icles with low­
s lung chassis (spo rts chas sis)* and fully load ­
ed vehicles.
Driving through water
on roads
Note the following to avoid ve hicle damage
when driving through water, for e xamp le on
flooded roads:
- The wa ter must not be any higher than the
bottom of the vehicle body .
- Do not dr ive faster than walk ing speed .
•
•

194 Driving and en vironm ent
8_ WARNING
After driving through water, mud, slush,
etc ., the brakes may be slow to take effect
because of wet brake rotors and pads. Dry
the brakes first by braking carefully to re­
store the full braking effect.
CD Note
Vehicle components such as the engine,
transmiss ion, suspension or electrical sys­
tem can be severely damaged by driving
through wate r.
@ Tips
- Check the depth of the water before dr iv­
i ng through it.
- Do not stop the veh icle, dr ive in reverse
or switc h the engine off when driving
t hr ough water.
- Keep in mind that oncoming vehicles
may c reate waves that raise the water
l evel and make it too deep fo r you r vehi­
cle to dr ive through safely.
-
- Avoid dr iving thro ugh salt water because
i t can ca use corrosion.
Catalytic converter
It is very important that your emission con­
trol system (catalytic converter) is function ­
ing properly to ensure that your vehicle is run­
ning in on environmentally sound manner.
,,. Always use lead-free gasoli ne¢ page 211,
Fuel supply .
,,. Never run the tank down a ll the way to
empty.
,,. Never put too much motor oil in your en-
gine ¢
page 221, "t':::r. Adding engine oil.
,,. Never t ry to push- o r tow-start your veh icle.
The catalytic converter is an effic ient "clean­
up" device built into the exhaust system of
the vehicle. The catalytic converter burns
many of the polluta nts in the exhaust gas be­
fore they are released into the atmosphe re. The exclusive
use of unleaded f uel is critica lly
important for the life of the catalytic convert­
er and proper funct ion ing of the eng ine .
A WARNING
= -
-Do not park or operate the vehicle in
areas where the hot exhaust system may
come in co ntact with dry grass, brush,
fuel spill or other material wh ich can
cause a fire .
- Do not app ly additional undercoating or
r u stp roofing on or nea r the exhaust
manifold, exhaust pipes, cataly tic con­
ver ter or heat shields. Dur ing driv ing, the
substance used for under coa ting co uld
overhea t and cause a fire.
CD Note
- Be aware that just o ne tank filling with
leaded fu el w ill already ser io usly de ­
gr ad e the per form ance o f the catalytic
c onverte r.
- Do not ex ceed t he corre ct engine oil level
r:;!) page 2 21.
- Do not drive until the fuel tank be co m es
completely emp ty. The engine co uld mis­
fire . Unburned fuel could also get in to
the exhaust system and this co uld cause
the cata lytic converter to overheat .
- Do not turn off the igni tion whi le the ve ­
hicle is mov ing.
- Do not contin ue to ope rate your veh icle
unde r these conditions, as otherwise fuel
can reach the catalyt ic converte r. T his
co uld resu lt in overheating of the con­
verter, requir ing its replacement.
- To assure efficient operation of the Emis ­
sion Control System:
- H ave you r vehicle maintained p rope rly
and in accordance w ith the se rvi ce rec ­
ommen dat ions in yo ur Warranty &
M ain tenance boo klet.
- L ack of prope r maintenan ce as we ll as
i mprope r use of t he ve hicl e wi ll impair
the func tion of the em ission cont ro l
system and could lea d to damage .
Ill>

@ For the sake of the environment
Even when the Emission Control System is
operating properly, the exhaust gas can
have a sulfur-like exhaust gas smell under
some operating states. This depends on
the sulfur content of the fuel being used.
Using a different brand of fuel may help,
or filling the tank w ith lead-free super
grade gasoline.
Operate your vehicle
economically and minimize pollution
General
Your personal style of driving will determine
the economy of your vehicle, as well as ex­
haust and noise levels.
Fuel economy, environmental impact, and
wear on you r engine, bra kes and t ires largely
depend on th ree factors:
= your persona l dr iving style
- operating conditions
- technica l lim itations
I f you anticipate what yo u need to do next and
drive economically, you can easi ly cut your
fuel consumption by 10-15 percent. This sec­
tion will give you some t ips on how you can
he lp the environment and your pocketbook.
@ Tips
The consumpt ion estimates as published
by ENVIRONMENTAL PROTECTION AGENCY
(EPA) and Transport Canada may not corre­
spond to your actual consumption on the
road, wh ich will vary depending upon vehi­
cle load and speed, road and weather con­
ditions, tr ip length, etc.
Drive smoothly and keep a lookout
ahead
Vehicles use the most fuel when they are ac­
celerating.
" Avoid unnecessary accele rat ing and braking.
Dri vin g and en vironm ent 195
Vehicles use the most fue l when they a re ac ­
ce lerating. If you anticipate what is going to
happen next, you will need to brake less and,
th us, acce lerate less. Let the vehicle coast
whenever possible -for example when you see
that the next traff ic light is red.
Avoid full throttle
Driving at moderate speeds saves fuel and
improves your mileage.
" Try and keep well below your car's maxi-
mum speed.
Acce lerating gently red uces fue l cons ump­
tion, engine wear, and does not disturb the environment.
Fuel consumpt ion, exhaust emiss ions and en ­
gine noise increase disproportionately at high
speeds . If you drive at approximately th ree
quarters of top speed, fuel consumption w ill
be reduced by one half. Never drive faster
than the posted speed limit and weather con­
ditions perm it.
Reducing unnecessary idling
Even when your car is just idling it burns up
fuel .
" Shut the eng ine off when you are not driv­
ing the vehicle.
" Do not warm up the ve hicle by letting the
eng ine run at idle .
It makes sense to shut off the engine in traffic
jams, when wa it ing for tra ins to pass at rail­
road crossings, or at traffic lig hts t hat have
long waits on red . T ur ning the eng ine off for
just 30-40 seconds saves mo re fuel than is
bur ned star ting the e ngine again.
It takes a long t ime for the engine to warm up
fully when it is run ning at idle . However, wea r
and noxious emissions are espec ia lly high
whe n the eng ine is wa rm ing up. So yo u shou ld
drive away as soon a s you start the e ngine and
avo id r unning at high rpms whi le the engine is
still warming up.
Ill-
•
•