Gear AUDI Q2 2021 Owner´s Manual

Driver assist systems

CO

< o rN
r>
rN
t-H
o < 00
-The automatic brake application with in­
creasing brake force can be cancelled by ap­
plying the brakes yourself or by pressing the
accelerator firmly.
- In certain situations, a warning may be giv­
en by the rear cross-traffic assist even if
there is no traffic in the critical zone, for in­
stance when parking or manoeuvring the ve­
hicle in reverse.
- The rear cross-traffic assist is deactivated
automatically if you deactivate the
ESC.

-The rear cross-traffic assist is switched on/
off via the parking aid
^>page
134.
-The system is not available in towing mode.
Driver messages
Applies to: vehicles with Audi side assist
Should the side assist be deactivated automati­
cally, a driver message will appear in the instru­
ment cluster display.

O
Audi side assist: system fault!
The system cannot detect vehicles reliably and
will be deactivated. The sensors are out of align­
ment or defective. Have the system checked by a
qualified workshop soon.

O
Audi side assist: currently unavailable. No
sensor vision

O
Audi side assist: currently unavailable.
Sen­

sor view restricted due to surroundings. See
owner's manual
The radar sensors are blocked. The area in front
of the sensors must not be obstructed by bicycle

racks,
stickers, deposits or any other substances.
If necessary, clean the area in front of the
sen­

sors
^>page
128, Fig. 120.

O
Audi side assist: currently unavailable
The side assist is temporarily inoperative and
cannot be switched on (for instance if the battery
is not sufficiently charged).

O
Audi side assist: unavailable in towing mode

2
Audi side assist: unavailable in towing mode
The side assist function will be switched off auto­
matically after a short time when the electrical
connector for the trailer socket is plugged in on
vehicles with a factory-fitted towing bracket. If
the towing bracket is not factory-fitted the side
assist function may not be switched off automat­
ically. The side assist must not be used when
towing a trailer.

O Rear
parking aid: obstacle detection limited
The rear cross-traffic assist is not available. Ei­
ther the ESC is switched off or the radar sensors
may be obstructed by a bicycle rack, stickers,
leaves, snow or similar objects. Switch on the ESC
or, if necessary, clean the area in front of the
sen­

sors
<3page
128, Fig. 120. If this message re­
mains displayed, drive to a qualified workshop
soon and have the fault rectified.
Audi drive select
Introduction
Applies to: vehicles with Audi drive select
Audi drive select alLows you to use different set­
ups on your vehicle. The modes efficiency*, com­
fort, auto and dynamic allow the driver, for ex­

ample,
to change from a sporty mode to a more
comfortable one via the
&&
button in the centre
console or via the infotainment system. In
addi­

tion,
the individual* mode allows you to adapt
the vehicle set-up to
suit
your personal driving

style.
For example, you might choose to combine
a more dynamic engine set-up with a lighter
steering response.
Description
Applies to: vehicles with Audi drive select
The possible vehicle set-up in each mode de­
pends on which equipment is installed on your
vehicle. The engine and steering are basic parts
of your vehicle which are always included in the

set-up.

Engine and automatic gearbox*
The response of the engine and automatic
gear­

box* to accelerator pedal movements will be
more spontaneous or balanced, depending on
131

Driver assist systems
which mode you select. In the performance-
oriented dynamic mode, the automatic gearbox
changes gear at higher engine speeds.
By contrast, in efficiency* mode, the automatic
gearbox* selects the next gear at lower engine
speeds and the coasting mode is activated

^>page
91. This helps to reduce fuel consump­

tion.

Suspension control (Audi magnetic
ride)*

The suspension control uses sensors to collect in­
formation on steering movements, braking and
acceleration input by the driver, road surface
quality, road speed and vehicle Loading. With
Audi drive select you can choose between dynam­
ic and comfort-oriented suspension set-ups (dy­
namic and comfort modes), or opt for
a
more
balanced set-up (auto mode).
Steering
The degree of power assistance can be varied.
Various modes are possible
^>page
133. The
light, indirect steering response in comfort mode
is particularly suitable on long motorway trips,
for instance. The steering has a tighter, more di­
rect feel in dynamic mode.
The steering response is even more agile on
vehicles with progressive steering*.
Audi adaptive light*
The adaptive light system adjusts the light distri­
bution according to the mode selected.
Air conditioner*
The air conditioner runs in a particularly econom­
ical mode when the efficiency* setting is selec­

ted.
When this function is selected, eco* is shown
in the display of the automatic air conditioner.
Cruise control system*
The acceleration response is particularly econom­
ical in efficiency* mode.
Audi adaptive cruise control*
The acceleration mode can be varied from com­
fort to sport by changing the setting in drive se­
lect. The setting also determines whether the re­
sponse of the adaptive cruise control to the driv­
ing style of the driver in front is more balanced or
spontaneous. The efficiency* mode chooses a set­
up for maximum economy.
© Note
- On some models the vehicle's maximum
speed can only be obtained in the auto and
dynamic modes.
- Applies to vehicles with manual gearbox: An
E appears in the gear-change indicator when
efficiency* mode is activated.
- Applies to vehicles with automatic gearbox:
Selector lever position
S
is automatically se­
lected when dynamic mode is activated.
E
is
selected in efficiency* mode.
- Applies to vehicles with automatic gearbox:
If
you
select efficiency* mode when the se­
lector Lever is in position D,
E
will automati­
cally appear in the instrument cluster dis­
play.
- Applies to vehicles with manual gearbox: If
you press the accelerator right down past
the point of resistance in efficiency* mode,
the engine power is automatically control­
led to give your vehicle maximum accelera­

tion.

- Please note that the efficiency* mode is not
available in towing mode.
Selecting the driving mode
Applies to: vehicles with Audi drive select

You
can choose between efficiency*, comfort, au­

to,
dynamic and individual*.

Fig.
123 Centre console: Button for drive select

•
Press the
ism
button
^>Fig.
123 repeatedly until
the desired mode appears on the instrument
cluster/infotainment display. Or: •
132

Driver assist systems

•
Select the following on the infotainment sys­

tem:
|MENU|
button > Car
>
left control button
> Audi drive select.

•
Select and confirm the desired setting.
You can change the mode while the vehicle is sta­
tionary or moving. If traffic conditions permit,
take
your
foot off the accelerator briefly after you
change the mode so that the new mode is also
activated for the engine.
efficiency* - trims the vehicle to a fuel-saving
set-up and helps the driver adopt an economical
driving style.
comfort - alters the vehicle set-up for a more
comfortable ride and is suitable for long motor­
way trips, for instance.
auto - gives an overall impression of
a
comforta­
ble but dynamic ride and is a good choice of set­
up for everyday use.
dynamic - gives the vehicLe a tighter set-up and is
ideal for performance driving.
individual* -
^>page
133.
A WARNING
Always keep an eye on the traffic when using
the drive select controls - Risk of accident!

CO

rN
r>
rN
•-i

00
Configuring individual mode

You
can configure your own personal vehicle set-up.

*-
Select: |MENU| button > Car
>
Audi drive select
> individual
>
right control button.
The individual* driving mode will automatically
be activated when you have finished configuring
the settings.
Your vehicle's equipment and engine determine
which systems you can select. The following ta­
ble provides an overview of the characteristics.
Systems
Engine/Gearbox
Steering
Audi adaptive cruise control*
Suspension control*
comfort
Comfortable
Comfortable
Comfortable
Comfortable
auto dynamic
Balanced
Balanced
Balanced
Balanced
Dynamic
Dynamic
Dynamic
Dynamic
© Note
Your settings in individual* mode are stored
automatically and assigned to the remote
control key currently in use.
133

Parking aids
- To ensure that the acoustic parking aid
works properly, the sensors must be kept
clean and free of snow and ice.

CO

< o rN
iv
rN
•-i

00
Rear parking aid
Description
Applies to: vehicles with rear parking aid

The
rear parking aid is an acoustic parking
sys­

tem.
Description
Sensors are located in the rear bumper. When
the sensors detect an obstacLe, you are alerted by
acoustic signals (beeps).
Please ensure that the sensors are kept free of
stickers, deposits and any other substances
which could impair the function of the system.
Notes on cleaning
^>page
312.
The measuring range of the sensors starts at
about:
Rear Side
Centre
0.90 m
1.60 m
The acoustic signals sound with increasing
fre­

quency as you approach the obstacle. A warning
tone will sound continuously when the vehicLe is
less than approx. 0.30 m away from the obstacLe.
Stop reversing immediately
•=>
A in General notes
on page 134,
<=>©
in General notes on page 134
The volume of the warning beeps will be reduced
after
a
few seconds until it is muted if the vehicLe
remains at a constant distance from a detected
obstacle (but not if the obstacle is closer than
0.30 m). If the tone is muted and the obstacLe
comes closer than before, the tone will sound

again.
If the tone is muted and the obstacle is
further away than before, no tone will sound.
Please watch the area surrounding the vehicle
when driving off.
Activating
The parking aid is switched on automatically
when reverse gear is engaged. You will hear a
brief acknowledgement tone.
Parking system plus
Description
Applies to: vehicles with parking system plus/park assist

The
parking system plus provides acoustic and
visual assistance when parking.

Fig.
124 Diagram
Sensors are located in the front and rear bump­

ers.
When the sensors detect an obstacle, you are
alerted by acoustic signals (beeps) and a graphic
display.
Please ensure that the sensors are kept free of
stickers, deposits and any other substances
which could impair the function of the system.
Notes on cleaning
<3>page
312.
Approximate range for each display zone:
®
®
©
®
©*
1.20 m
0.90 m
1.60 m
0.90 m

0.90
ma)

a'
Applies to vehicles with park assist
The acoustic signals sound with increasing
fre­

quency as you approach the obstacle. A warning
tone will sound continuously when the vehicLe is
less than approx. 0.30 m away from the obstacLe
(or less than approx. 0.20 m away in zone (D*).
Stop moving immediately
•=>
A in General notes
on page 134,
•=>©
in General notes on page 134
The volume of the warning beeps will be reduced
after
a
few seconds until it is muted if the vehicLe
remains at
a
constant distance from a detected
obstacLe (but not if the obstacLe is closer than
0.30 m). If the tone is muted and the obstacle
135

Parking aids

comes
closer than before, the tone will sound

again.
If the tone is muted and the obstacLe is
further away than before, no tone will sound.
Please watch the area surrounding the vehicle
when driving off.
©
Zone
(§)*
is detected and analysed as the
vehi­

cLe is moving past. When you switch the
igni­

tion off and on again or open the door, or af­
ter the vehicle has been stationary for
a
while,
the ambient surroundings may have changed.
Zone
0*
is displayed in black on the infotain­
ment display for this reason.
Switching on/off
Applies to: vehicles with parking system plus/park assist

Fig.
125 Centre console: Button for parking aid

^H i m
1 •rif/^^^y^H <

12|
1 )
'.•;"

•BiHiSi
-

Fig.
126 Infotainment display: Proximity graphic
Switching on

•
Engage reverse gear, or

•
Press the
P»i
button in the centre console

^>Fig.
125. You will hear
a
brief acknowledge­
ment tone and the LED in the button will light

up-

Switching
off

• Drive forwards faster than 10 km/h, or

*•
Press the
?">k
button, or

•
Switch off the ignition.
Automatic activation
The parking aid is activated automatically when
the vehicLe approaches an obstacLe from a dis­
tance of approx. 95 cm at speeds below 10 km/h.
You will hear the warning beeps when the obsta­
cle is within a distance of approx. 50 cm. If the
parking aid is switched off by pressing the
P*A

button,
it is only reactivated automatically if one
of the following conditions has been met:
- The vehicle is driven faster than 10 km/h.
- The ignition is switched off and on again.
-The parking brake is applied and released

again.

- The selector lever is in position P (automatic
gearbox).
Segments in the graphic display
You can estimate the distance to an obstacle by
referring to the segments in front of and behind
the vehicLe or the segments surrounding the ve­
hicle (on
vehicLes
with park assist*)
^>Fig.
126.
The red lines* indicate the anticipated path of the
vehicle, depending on the steering wheel angle.
A white segment indicates an obstacle that has
been detected beyond the path of
travel.
Red
segments represent objects detected within the
path of
travel.
The closer the vehicle gets to the
obstacLe the closer the segments move towards
the vehicLe in the graphic. At the Latest when the
penultimate segment is highlighted the vehicle
has reached the danger (collision) zone. Obsta­
cles within the danger (collision) zone are shown
in red, even if
they
are beyond the path of travel.
Stop moving immediately
•=>
A in General notes
on page 134,
•=>©
in General notes on page 134
136

Parking aids
© CAUTIO
- Please observe the safety warnings
o©
in
General notes on page 134.
-The orange orientation lines on the infotain­
ment display show the path of the rear end
of the vehicle if
you
were to reverse using
the current steering angle. Please note that
the front end of the vehicle swings out fur­
ther than the rear. Please make sure you
keep a sufficient distance between the
vehi­

cle and any obstacles to make sure that the
exterior mirror or edge of the vehicle do not
collide with the obstacles.
Switching on/off
Applies to: vehicles with reversing camera
Switching on

•
Engage reverse gear, or

•
Press the
P*A
button in the centre console

^>page
136, Fig. 125. You will hear
a
brief ac­
knowledgement tone and the LED in the button
will Light up.
Switching off

•
Drive forwards faster than 10 km/h, or

•
Press the
P-A
button, or

•
Switch off the ignition.
-The graphic on the right of the display helps
identify the critical area of the vehicle.
- You can change the display and adjust the
volume of the beeps
^page
143.
Parking perpendicular to the roadside
Applies to: vehicles with reversing camera
This view can be used when parking your vehicle
in a garage or parking bay.

Fig.
130 Infotainment display: Approaching a parking
space

Fig.
131 Infotainment display: Aligning the vehicle

•
Switch on the infotainment system and select
reverse gear.

•
The orange orientation lines
(Ï)
represent the
path of the vehicle. Turn the steering wheel un­
til the orange orientation lines are pointing to­
wards the parking space
^>Fig.
130. You can es­
timate the distance to an obstacLe by referring
to the markings
(2).
Each marking is equivalent
to approx. 1 metre. The blue marking is an ex­
tension of the vehicle outline and reaches
about five metres to the rear of the vehicle.

•
Reverse into the space and adapt the steering
angle to the parking space, using the orange
lines to assist you
^>^in
General notes on
page 137,
*=>(T)in
General notes on page 138.
(3) represents the rear bumper. Stop moving, at
the latest, when the red orientation Line (4) is
bordering on an obstacle.
138

Parking aids

CO
< o rN
iv
rN
i—i

00
Important: For the best parking result, you
should maintain a distance of approx. 1 metre to
the row of parked cars.

•
To switch between parallel
(Â)
perpendicular
forwards
(B)
and perpendicular in reverse (?)
parking modes, turn the rotary pushbutton to
select the desired mode. The system only
shows parking modes that are currently possi­

ble.

•
Operate the turn signal. The desired side of the
road will be scanned.

•
To park parallel to the roadside, drive forwards
at not more than 30 km/h. Or:

•
To park perpendicular to the roadside, drive
forwards at not more than 20 km/h.

•
The system will display
a
parking space when it
finds one
^Fig.
137. Please check that the
parking space is suitable for your vehicle.

•
To park using the system, follow the instruc­
tions on the display.
If
you
exceed a speed of about 50 km/h, the park
assist will be switched off.
The park assist will display
a
parking space only if
it is Long and wide enough for the vehicLe.
© Note
-You can select any one of the parking op­
tions found. The potential parking space is
displayed until you have driven too far away
from it.
- You can activate the park assist after you
have already driven past a parking space (as
long as you were driving slowly enough). To
do so, press the
P©
button and operate the
turn signal.
- The system displays the right or left side of
the
road,
depending on which turn signals
you operate.
- The best parking results will be achieved if
you position the vehicle as parallel as possi­
ble to the line of parked cars or the kerb be­
fore you start the actual parking manoeu­

vre.

- If there are suitable parking spaces on both
sides of the road (for instance on a one-way
street), you can change the direction of the
turn signals to park on the other side, even
if
you
have already activated the park assist.
Starting a parking manoeuvre
Applies to: vehicles with park assist

The
driver is responsible for parking the vehicle.

Id it nl ila 1 i
L
ml\Jf '- ,H
i^*feâSi^T^,s*'ii^**£^B
'
1
Jr
r
i
fm
-
rf
"
!B—^-ASSL
^
tc^^^T-^T^^Tfr^a^j^

*
If*
Tf dl if
ïï
F ~"i
1VT"
•*-•.'' iiS^S

Fig.
138 Infotainment system: Prompt to continue revers­
ing (example: parking parallel to the roadside)

•
Drive forwards until the instructions for the au­
tomatic parking manoeuvre appear on the info­
tainment display
^>Fig.
138
^/^
in Descrip­
tion on page 139,
o(T)
in Description on
page 140. A
P
will appear in the intended park­
ing space as soon as the vehicle reaches the
correct position.

•
If necessary, you can use the rotary pushbutton
to change the parking mode in order to take a
different approach to the parking space.

•
The park assist is ready when the message
Please select reverse gear and let go of the
steering wheel appears on the infotainment
display.

•
After stopping for
a
moment, select reverse
gear.

•
Take your hands off the steering wheel.

•
Watch the
road.
When the road is clear, press
the accelerator gently
^/^
in Description on
page 139,
•=>(?)
in Description on page 140.

•
Follow the instructions on the display

^>page
142 and the acoustic warning tones
until the parking manoeuvre is complete. The
arrows on the vehicLe show the required direc­
tion of travel.
The park assist automatically steers the vehicle
into the parking space while the driver operates
the pedals. The maximum parking speed is 7 km/
h. The park assist will be deactivated if
you
drive
too fast or move the steering wheel by hand. To •
141

Parking aids
continue the parking manoeuvre, press the
P© button again. The park assist will reappear on
the display.
You can cancel the direction of travel given by
the system before parking by shifting be­
tween forwards/reverse gear. The system will
then calculate the further path and steering
directions for the manoeuvre based on the
position of the vehicle.
Driving out of a parking space parallel to
the roadside
Applies to: vehicles with park assist

The
driver is responsible for manoeuvring the ve­
hicle out of the parking space.
If the vehicle is parked parallel to the roadside,
the park assist can help you to drive out of the
parking space.

•
Start the engine.

•
Press the
P©
button
^>page
140, Fig. 135.

•
Wait until the following text appears on the in­
fotainment display: Specify direction with turn
signal to leave parking space.

*•
Operate the appropriate turn signal. The mes­
sage Start automatic unparking procedure will
appear.

*•
Take your hands off the steering wheel.

•
Press the rotary pushbutton to start automatic

unparking.

•
Watch the
road.
When the road is clear, press
the accelerator gently
^ ^
in Description on
page 139,
^>(J)in
Description on page 140.

•
Follow the instructions on the display

^>page
142 and the acoustic warning tones
until you are
dear
to leave the parking space.

•
Drive in the direction specified by the arrows on
the vehicle.

•
The procedure is over when no more manoeu­
vring is necessary in order to drive out of the

space.
Take over the steering.
The park assist automatically steers the vehicle
out of the parking space while the driver operates
the pedals. The maximum manoeuvring speed is
5 km/h. The park assist will be deactivated if you
drive too fast or move the steering wheel by

hand.
To continue the parking manoeuvre, switch
the engine off/on. Then press the
P@
button

again.
Alternatively, drive out of the parking
space without using the park assist.
Driver messages
Applies to: vehicles with park assist
Park assist: cancelled. Steering input detec­

ted.
Continue steering vehicle!
The steering assistant has been deactivated be­
cause the driver has intervened in the steering.
To continue the parking manoeuvre, press the

"©
button again.
Park assist: time limit exceeded
Park assist: cancelled. Time limit exceeded.
Continue steering vehicle!
The parking manoeuvre was not completed
with­

in about six minutes after the park assist was ac­

tivated.
To continue the parking manoeuvre,
press the P© button again.
Park assist: cancelled. Speed too high. Con­
tinue steering vehicle!
You were driving too fast into the parking space.
Do not drive faster than 7 km/h.

i
Park assist: cancelled. Stabilisation control
(ESC) input. Continue steering vehicle!
The ESC has intervened. Take over the steering.
Finish parking without the park assist or drive out
of the parking space.
Park assist: currently unavailable. Stabilisa­
tion control (ESC) off
The ESC has been switched off. The ESC must be
switched on before the park assist can be used.
| Park assist: fault. Please contact workshop
i Park assist: fault. Continue steering vehicle!
Please contact workshop
Please contact a qualified workshop. The park as­
sist cannot be used to park the vehicLe if
a
system
fault occurs.

|
Park assist: currently unavailable
142

Parking aids

CO

<
o
rN
iv
rN
t-H
o
< 00
Park assist: currently unavailable. Continue
steering vehicle!
The park assist cannot be used to park the
vehi­

cle.
Try repeating the parking manoeuvre or
switching the ignition off and on again.
3 Park assist: ended. Please take over steering
and continue driving
The park assist has finished manoeuvring the ve­
hicle out of the parking space. Please take over
the steering.
Park assist: cancelled. Space too small. Con­
tinue steering vehicle!
The park assist cannot be used to park the vehicle
in this space. Park the vehicle without using the
park assist or look for a bigger space.
Park assist: cancelled. Obstacle detected.
Please take over steering.
The park assist has interrupted the parking ma­
noeuvre to avoid a collision between the vehicle
and an obstacLe.
Park assist: ended
3 Park assist: ended. Please take over steer­

ing.

The park assist has finished the parking manoeu­

vre.

Park assist: stabilisation control (ESC) input
The parking space indicated has been rejected be­
cause the ESC has intervened.
Park assist: currently unavailable. Towing
mode
The park assist cannot be used to park the vehicle
when towing a trailer.

1
Park assist: not stopped long enough
After you select reverse gear, the vehicle has to
remain stationary for
a
moment so that the park
assist can activate the steering. Follow the direc­
tions given in the display.

3
Park assist: cancelled. Assist function un­
available for leaving parking space. Space too
small
The assist function is unable to automatically
steer the vehicle out of the parking space be­
cause the space is too small. Manoeuvre the
vehi­

cle out of the parking space without using the
park assist.
Park assist: cancelled. Continue steering ve­

hicle!

The park assist has interrupted the parking ma­
noeuvre.
Settings for parking aid

Applies
to: vehicles with rear parking aid/parking system

plus/reversing
camera/park assist

You
can change the settings for these functions
on the infotainment system.

•
Select the following on the infotainment sys­

tem:
|MENU[
button > Car
>
left control button
> Driver assist
>
Parking aid. Or:

•
Select the right control button* on the infotain­
ment system when the parking aid is activated.

End*
- To cancel the parking aid
Activate automatically - To switch automatic ac­
tivation on/off
Front volume* - Volume for the front and side*
zones
Rear volume - Volume for the rear zone

In-car
entertainment fader - The volume of the
current audio or video source is reduced when the
parking aid is switched on.
You will hear
a
short test tone each time you
make a new setting.
Trailer view* - To display the trailer view
- Some of the menus can only be called up via
the right control button when the parking
aid is activated.
- The volume and automatic activation set­
tings are automatically stored and assigned
to the remote control key in use.
143

Parking aids
Fault warnings
Applies to: vehicles with rear parking aid/parking system
plus/reversing camera/park assist

[3
Rear parking aid: fault. Obstacles cannot be
detected

O
Front parking aid: fault. Obstacles cannot be
detected

O
Parking aid: fault. Obstacles cannot be de­
tected
If any of these messages appears, a system
mal­

function has occurred. The LED in the
P*A
button
will flash in addition when the system is activa­

ted.
The corresponding message will then only
appear when you activate the parking aid
man­

ually with the button.

[3
Rear parking aid: obstacle detection limited
The rear cross-traffic assist*
^>page
130, Rear
cross-traffic assist is not available. Either the ESC
is switched off or the radar sensors may be ob­
structed by a bicycle rack, stickers, leaves, snow
or similar objects. Switch on the ESC or, if neces­
sary, clean the area in front of the sensors

^>page
128, Fig. 120. If this message remains

displayed,
drive to a qualified workshop soon and
have the fault rectified.
Parking system plus* / park assist*
If a sensor or loudspeaker malfunctions, the
f&L

symbol will be shown on the infotainment dis­
play in front of or behind the vehicle. If
a
rear
sensor malfunctions, obstacles will only be dis­
played in zones
(A)
and
(B)
<^>page
135, Fig. 124.
If a front sensor malfunctions, obstacles will only
be displayed in zones (?) and (5).
Towing bracket
Applies to: vehicles with rear parking aid/parking system
plus/reversing camera/park assist and towing bracket
When the trailer socket is connected, the rear
and side* parking sensors are NOT activated
when you select reverse gear or press the
P*A
but­

ton.
This results in the following restrictions:
Rear parking
aid*

There is no distance warning.
Parking system plus* / park assist*
There is no rear or side* distance warning. How­
ever, the system will still give a warning when
obstacles are detected while driving forwards.
The proximity graphic will switch over to towing

mode.

Reversing camera*
There is no rear or side* distance warning. How­
ever, the system will still give a warning when
obstacles are detected while driving forwards.
The proximity graphic will switch over to towing

mode.
The image of the reversing camera will
then be shown without orientation lines and blue
area markings.
(T) Note
Towing brackets which are not factory-fitted
can restrict or impair the function of the park­
ing aid.
144