AUDI TT COUPE 2016 Owner's Guide

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
Central locking switch
Fig. 20 Driver's door: central loc king switch
... To lock the veh icle, press the@! button ¢,&. .
... Press the !ill button to unlock the veh icle .
When locking
the vehicle with the central locking
switch, the
following applies :
- Opening
the door and the lu ggage compart­
ment lid from the outside is not possible (f or
sec urity such as when stopped
at a light) .
- The
LED in the central locking switch turns on
when all doors are closed and locked.
-
You can open the doors individually from the
inside
by pulling the door handle .
- In the event of a crash with airbag deployment,
the doors unlock automatically to allow access
to the vehicle .
.&. WARNING
-The power locking switch works with the ig­
nition off and automatically locks the entire
vehicle when
the~ button is pressed .
- The centra l loc kin g switc h is inoperative
when
the veh icle is l ocked from the outside.
-
Locked doors make it more difficult for
eme rgency workers
to get into the veh icle,
whic h puts lives at risk. Do not leav e anyone
behi nd i n
the ve hicle , especially children.
@ Tips
Your vehicle locks a u
tomatically when it
reaches a speed of 9 mph (15 km/h) (Auto
Lock) q page 25. You can unlock the vehicle
ag
ain usi ng the [ill button in the ce ntral loc k­
ing switch.
.....
"' l) This functio n is not availa ble in all countries . .....
Opening and closing
Setting the central locking system
In the Infotainment system, you can set which
doors the central locking system will unlock .
... Select in the Infotainment system: I MENU! but­
ton> Vehicle> left control button >Vehicle set­
tings .
Door unlocking
-you can decide if All doors or
only
the Driver door should unlock. The luggage
compartment
lid also unl ocks when All is select ­
ed. If you select Driver i n a vehicle with a conve n­
ience key*, only the doo r whose handle you pull
will un
lock .
If you select Driver , all the doors and luggage
compartment
lid will unlock if you press the@l
button on the remote control key twice.
Fold mirrors * -if you select On, the exterior rear­
view mirrors fold in automatically when you press
the l:ru button on the remo te contro l master key
or touch th e s ensor* in th e handle .
Lock when driving l) -if you select On, the vehi­
cle locks automatically when driving. All of the
doo rs and the luggage compartment lid lock.
29

Downloaded from www.Manualslib.com manuals search engine Opening and closing
Emergency unlocking and locking the doors
®
Fig. 21 Driver 's door: door lock cylinder
F ig . 2 2
Front passenger's door: emergency release
If the central locking system malfunctions, you
must unlock/lock the doors separately using the
mechanical key.
Unlocking /locking the driv er's door with the
mechanical key
•Remove the mechan ical key ¢ page 26.
•To unlock the d river's door, turn the key to the
open position @¢fig. 21.
•To lock the driver's door, move the selector lev­
er to the P position (automatic transmission)
and tur n the key once to the close position@ .
Locking the front passenger's door with the
mechanical key
The emergency release is located on the edge of
the front passenger's door. It is only visible when
the door is open.
• Remove the mechan ica l key¢ page 26.
•Pull the cap out of the opening i::::> fig. 22.
•Insert the key into the slot inside and turn it all
the way to the right (right door) or to the left
(left door*).
30
Once the front passenger's door is closed, it is no
l
onger possible to open it from the outside. The
door can be opened from the inside by pulling
the door handle.
Anti-theft alarm system
If the anti-theft alarm system detects a vehicle
break-in, audio and visual warning signals are
triggered. The anti-theft alarm system is activat­
ed when the vehicle is locked as usual. It is
switched off when unlock ing.
Luggage compartment
lid
Opening/closing the luggage compartment
lid
Fig. 23 Opened luggage compartment lid
-
•
•
•
'
Opening the luggage compartment lid
m 0 0
~ m
.. Press the la l button on the remote control key
for at least several seconds to open the luggage
compa
rtment lid . Or
..
Lift the luggage compartment lid .
Closing the luggage compartment lid
• Pull down the luggage compartment lid and let
it close using a gentle push i::::> .&,.
_&WARNING
- Due to the risk of inju ry, a lways be aware of
the rear passengers when closing the lug­
gage compartment lid.
- After closing
the luggage compartment lid,
make sure that it is latched. Otherwise the
luggage compartment lid cou ld suddenly ,...

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
.....
"' .....
open when driving, which increases the risk
of an accident.
- Never drive with
the luggage compartment
lid ajar or open, because poisonous gases
can enter the vehicle interior and create the
risk of asphyxiation.
- Never leave your vehicle
unattended when
the luggage compartment lid is open. A
child could climb
into the vehicle through
the luggage compartment. If the luggage
compartment lid was then closed, the child
would be
trapped in the vehicle and unable
to escape. To reduce the risk of inju ry, do
not allow children to play in or around the
vehicle. Always keep the luggage compart­
ment lid and the doors closed when the ve­
hicle is
not in use.
- Always make sure no one is in the luggage
compartment lid's range of motion when it
is closing, especially near the hinges. Fin­
gers or hands could be pinched.
@ Tips
-When the vehicle is locked, the luggage
compartment lid can be unlocked separately
by pressing the l.::::11 button on the remote
control key. When the luggage compart­
ment lid is closed again, it locks automati­
cally.
-
In case of an emergency or a faulty handle,
the luggage compartment lid can be opened
manually from the inside¢ page 31.
Opening and closing
Luggage compartment lid emergency
release
The luggage compartment lid can be released in
an emergency from
the inside.
Fig. 24 The emergency release is accessed on the left side
of
the luggage compartment underneath the rear w indow.
F ig.
25 Sect io n: inside of luggage compartment: emergen­
cy re lease
.. Tilt the left rear seat backrest forward.
.,. Pry out the cover¢ fig. 24 using the mechanical
key
9 page 26.
.. Pull the plastic cord in the direction of the ar­
row¢ fig. 25 .
31

Downloaded from www.Manualslib.com manuals search engine Opening and closing
Power windows
Controls
The driver can control all power windows.
Fig. 26 D river's door: powe r w in dow controls
All power window switches h ave a two- stage
function:
Opening the windows
"' Press t h e switch to the first level and hold it
until the window reaches the desired position .
"'To open the window completely, press the
swi tch all the way down to the second level
briefly .
Closing the windows
"'Pull the switch up to the first level and hold it
until the window reaches the desired position.
"'To close the window completely , pull the
switch u p to the second level briefly.
Power window switches
CD Left front door
@ Right front door
A WARNING
- Always take the vehicle key with you when
leaving the vehicle, even for a short period
of time. This applies particularly when chi l­
dren remai n in the vehicle. Otherwise the
children could start the engine or operate
electrical equipment (e .g . power windows).
T he
power windows are functional until the
driver's door or passenger's door has b een
o pened.
- Pay carefu l attention when closing the win­
dows. It could cause in jur y by pin ching .
32
N
N
M 0 ::) CX> ID
-1
-When locking the vehicle from o utside, the
veh icle must be unoccupied since the win­
dows can no longer be opened in an emer­
gency.
(l} Tips
-After turning the ignition off you can s till
open and close the windows for approxi­
mately 10 mi nutes. The power windows are
not switched off until the driver 's door or
passenger's door has been opened.
-When you open the doors, the windows au­
tomatically lower approximately 10 mm.
Convenience opening/closing
All windows can be opened and closed at the
same time.
Convenience open feature
"' Press the~ button on the remote contro l key
until all windows reach the desired position.
Convenience close feature
"' Press the ~ button on the remote control key
until all w indows are closed~ A or
Convenience closing with the convenience
key*
"'Touch the sensor * on the door handle long
enough until all w indows are close d. Do not
place your hand in the door handle when doing
this.
Setting convenience opening in the
Infotainment system
.. Select in the Infotainment system: IMENUI but­
ton > Vehicle > left control button >Vehicle set­
tings .
To enable the conven ience window opening f u nc ­
tion, the Long press to open windows function
must be switched on.
A WARNING
-Never close the windows ca relessly or in an
uncontrolled manner, because this increas­
es th e risk of injury.

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
.....
"' .....
-For security reasons, the windows can only
be
opened and closed with the remote con­
trol key at a maximum distance of approxi­
mately 6 ft (2 m) away from the vehicle.
When pressing the[@ button, always watch
the windows while they are closing so that
no one is pinched in the window. The closing
process will
stop immediately when the~
button is released.
Correcting power window malfunctions
After disconnecting the vehicle battery, the one­
touch up
and down feature must be activated
again.
~ Pull the power window switch until the window
is completely ra ised.
~Release the switch and pull it again for at least
one second.
Garage door opener
(Homelink)
Description
Applies to: vehicles with garage door opener (Homelink}
Fig.
27 Garage door opener: examp les of usage for diffe r­
ent system s
W ith the garage door opener (Homelink), you
can activate
systems such as the garage doors,
security
systems or house lights from inside your
vehicle. Up to three remote control functions can
be
programmed to the three buttons that are in­
tegrated in the control unit above the rearview
mirror .
T o
be able to operate systems using the garage
door opener, the buttons in the control unit must
first be programmed .
Opening and closing
A WARNING
f=
When operating or programming the garage
door opener, make sure that no people or ob­
jects are in the area immediately surrounding
the system. People can be inju red o r property
can be damaged if struck when closing.
@ Tips
-For security reasons, we recommend that
you clear the programmed buttons before
selling the vehicle.
- For
further information regarding Home­
Link,
refer to www.homelink.com .
-For the Declaration of Conformity with the
prov is ions from the FCC in the United States
and Industry Canada, refer to~ page 297.
Operation
Applies to: vehicles with garage door opener (Home link)
Fig .
28 Contro l panel above the interio r rearv iew mirro r
Requirement: the button in the control panel
must be programmed~ page 34 and the vehi­
cle
must be located within range of the system,
suc h
as the garage door.
~ Press the button to open the garage door. The
green LED@ blinks or turns on.
~ Press the button again to close the garage
door.
(j) Tips
To open or close the garage door, do not
press the button longer than 20 seconds or
the garage door opener will switch to pro­
gramming mode.
33

Downloaded from www.Manualslib.com manuals search engine Opening and closing
Programming the transmitter
Applies to: vehicles with garage door opener (Homelink)
F ig.
29 Distance between the radiator grille and the re­
mote control transmitter
Programming the button : step 1 on the
control panel
1. Switch on the ign ition.
2.
Press both of the outside buttons on the con­
trol panel Q page 33, fig. 28 until the yellow
LED@ turns off and the green LED@ blinks.
This procedure clears
the standard codes that
were set at the factory and does not need to
be repeated again to program the other but­
tons.
3. Briefly press the button in the control panel
that you want to program.
4. Wait until the yellow LED@ blinks. The pro­
gramming mode is active for 5 minutes.
5.
Go in front of the vehicle with the original re­
mote control transmitter for the system that
you are programming to the control panel
button.
Programming the button : step 2 at the
radiator grille
6. Hold the remote control transmitter at the
vehicle radiator grille c:> fig. 29.
7 . Now press the remote control transmitter
until the turn signals on your vehicle blink.
This can
take up to 30 seconds.
8.
If the emergency flashers blink three times,
the programming was successful. If the
emergency flashers only blink one time, the
5 minute time limit for programming has ex­
pired
or the programming was unsuccessful.
Repeat the programming starting from the
third step or change the distance to the radi­
ator grille.
34
9. If the garage door or other systems do not
open with the Homelink buttons even if the
programming was successful, the system
may use a rolling code instead of a fixed
code.
You must also then perform rolling
co de
programmin g Q page 35.
The other two buttons in the control panel can be
programmed using the instructions given above.
Start with step 3.
Deleting button programming
The programmed buttons cannot be deleted indi­
vidually, they
must be deleted all at once. Repro­
gram the buttons if necessary.
... Sw itch on the ign ition.
... Press both of the outside buttons on the con­
trol unit until the yellow LED@ turns off and
the green LED@ blinks .
Reprogramming buttons
... Switch on the ignition .
... To reprogram an individual button, press the
desired button until the green LED@ turns off
and the yellow LED@ starts to blink (after ap­
proximately
20 seconds). Release the button
immediately. The programming mode is active
for S minutes.
... Continue with step 5.
(!) Tips
-The distance needed between the remote
control transmitter and the Homelink mod­
ule in the radiator grille c:> fig. 29 depends
on the system you are programming.
- Depending on the system model, you may
need
to release the button on the remote
control transmitter while it is programming
and press it again. Hold every position you
try when programming for at least 15 sec­
onds before trying a new position. Keep an
eye on the vehicle turn signals while doing
this.

Downloaded from www.Manualslib.com manuals search engine Rolling code programming
Applies to: vehicles with garage door opener (Homelink)
On some systems, programming a rolling code is
also necessary .
Identifying a rolling code
~Press the button in the control unit that is al­
ready programmed again and hold it down.
~ Pay attention to the LED@ ¢ page 33, fig. 28.
If the green LED blinks quickly, the system
(such as a garage door) has a rolling code.
~Program the rolling code as follows:
Activating
the system motor unit
~Locate the programming button on the system
motor unit. The exact location and color
of the
button may vary depending on the system man­
ufacture r's brand .
~Press the programming button on the system
motor unit (usually this w
ill act ivate a "display"
on the motor unit). You now have approximate­
ly 30 seconds to program th e button in the
contro l panel.
Programming the button in the control
panel
~ Press the previously programmed button in the
control pane l for 2 seconds.
~To complete rolling code programming, press
the button again for 2 seconds.
~On some systems, the button might need to be
pressed a third time to end
the programming
procedure .
After programming,
the system should recognize
the signal and operate when the button in the
control panel is pressed . Now you may program
the other buttons as needed .
(}) Tips
- The rolling code can be programmed more
quickly and more easily with
the help of a
second person.
-
If any difficulties occur when programming
the rolling code, it may be helpful to read
the system operating manual.
Opening and closing
35

Downloaded from www.Manualslib.com manuals search engine Lights and Vision
Lights and Vision
Exterior Lighting
Switching lights on and off
Fig. 30 Instrument panel: light switch
Light switch ·'t/;
Turn the switch to the corresponding position.
When
the lights are switched on, the :oo: symbol
turns on.
0 -lights are off (in some markets, the daytime
running
lights* are switched on when the ignition
is switched on.)
-USA models: the daytime running lights sw itch
on automatica
lly when the ignition is sw itched
on and
the light switch is set to the 0 or the
AUTO position (only in daylight). The Daytime
running lights
can be switched on and off in
the MMI ~page 37 Q &.
-Canada models: the daytime running lights
switch on automatically when the ignition is
switched on and the light switch is set to the 0,
:oo: or the AUTO position (only in daylight) QA .
AUTO* -automatic headlights switch on and off
depending on brightness, for example in twilight,
during rain
or in tunnels.
:oo: -Parking light
~D -Low beam headlight
~ -All weather lights*
All-weather lights*
In vehicles with all-weather lights, the front
lights are adjusted automatically so that you are
less likely
to see glare from your own headlights,
for example when driving on a wet road.
36
Automatic dynamic headlight range control
system*
Your vehicle is equipped with a headlight range
control system
so that the headlights do not
blind oncoming traffic if the vehicle load
changes. The headlight range also
adjusts auto­
matically when braking and accelerating .
Light functions
The following light functions are available de­
pending on vehicle equipment and only function
when the
light switch is in the AUTO position.
You can deactivate these functions in the Info­
tainment system under Audi adaptive light
Qpage 37.
Static cornering light* (vehicles with LED head­
lights) -the cornering light switches on automat­
ically when the steeri ng wheel is turned at acer­
tain angle at speeds up to approximately 44 mph
(70 km/h) and when the turn signal is activated
at speeds up to approxim ately 25 mph (40 km/
h). The area
to the side of the vehicle is illuminat­
ed better when turning.
Highway light function* (vehicles with LED head­
lights) -this function adapts the lighting for
highwa y driving based on vehicle speed.
Speed dependent light distribution* (vehicles
with LED headlights) -the speed dependent light
distribution adapts the light in towns and on
highways
or expressways. Intersections can also
be illuminated on vehicles
with a navigation sys­
tem*.
A WARNING
- Automatic headlights * are only intended to
assist the driver. They do not reliev e the
driver
of responsibility to check the head­
lights and to turn them on manually accord­
ing to the current ligh t and visibility condi­
tions. For example, fog cannot be detected
by
the light sensors . So always switch on the
low beam under these weather conditions
and when
driving in the dark ~D.
-If the battery is dra ining significantly, the
parking lights will switch off automatically
to reduce the risk of the engine not starting . ..,..

Downloaded from www.Manualslib.com manuals search engine Always make sure your vehicle is parked and
adequately lit according to the laws. Avoid
using
the parking lights for several hours.
Switch
on the right or left parking light if
possible.
-
Please observe legal regulations when using
the lighting systems described.
Tips
-The light sensor for the automatic head­
lights*
is in the rearview mirror mount.
Therefore, do not place any stickers in this
area on the w indshield.
-
Some functions of the exterior lighting can
be
adjusted ~page 3 7.
-
If yo u turn off the ign ition whil e the exterior
lights are on and open the door, you will
hear a warning tone.
- In some markets, the tail lights will switch
on when the daytime running lights switch
on.
- In cool
or damp weather, the inside of the
headlights, turn signals and tail lights can
fog over due to the temperature difference
between the inside and outside. They will
clear shortly after switching them on. This
does not affect the service life of the light­
ing.
Turn signal and high beam lever
The lever operates the turn signals, the high
beoms
and the headlight flasher.
@
,
I
@
Fig. 31 Turn signal and high beam lever
"' 0 0
a'.: CXl
Lights and Vision
Turn signals¢ Q
The turn signals activate when you move the lev­
er into a turn signal position when the ignition is
switched on.
@-right turn signal
@
-left turn signal
The turn signal blinks three times if you tap the
lever (convenience turn signal).
High beams and headlight flasher §D
Move the lever to the corresponding position:
®-high beams on
@-high beams off or headlight flasher
The . indicator light in the instrument cluster
turns on.
A WARNING
High beams can cause glare for other drivers,
which increases
the risk of an accident. For
this reason, only use the high beams or the
headlight flasher when they will not create
glare for other drivers.
Adjusting the exterior lighting
The functions are adjusted in the Infotainment
system .
... Select in the Infotainment system: IMENUI but­
ton> Vehicle > left control button >V ehicle set­
tings > Exterior lighting.
Automatic headlights
You can adjust the following settings in the Au­
tomatic headlights
menu:
Activation time -you can adjust ifthe headlights
switch on Early, Medium or Late according to the
sensitivity of the light sensor.
Audi adapti ve light* -you can switch adaptive
light On and Off.
Daytime running lights*
USA models : the daytime running lights can be
switched on or off using the MMI. Select On or
Off. ....
37

Downloaded from www.Manualslib.com manuals search engine Lights and Vision
Canada models: this function cannot be switched
off. They activate automaticall y each time the ig­
n ition is switched on. T his menu item is shown
with a "gray background".
Com ing home , Leaving home
The coming home function illuminates the area
outside the vehicle when you turn the ignition off
and open the driver 's door. To switch on the func­
tion, select Entry /exit lighting .
The leaving home ill uminates the area outside
the vehicle when you unlock the vehicle . To
switch
on the function, select Entry/exit light­
ing .
The coming home and leaving home f unctions
only operate when it is dark and the lig ht switch
is in
the AUTO position.
Emergency flasher
Fig. 32 Center conso le : eme rge ncy flash er button
The emergency flashers makes other drivers
aware of your vehicle in dangerous situations.
• Press the~ button to switch the emergency
flashers on or off.
You can indicate a
lane change or a turn when the
emergency fla sh ers are switched on by us ing the
turn sig nal lever. The emergency flashers stop
temporarily.
The emergency flashers also work when the igni­
tion is turned off.
(!) Tips
You should switch the emergency flashers on
if:
38
- You are the last c a r in a tra ffic jam so that
all other vehi cles approaching from behind
can see you, or if
- Your vehicle
has broken down or you are
having
an emergency, or if
- You r vehicle is
being towed or i f you are
towing another vehicle.
Interior lighting
Interior lighting
Fig. 33 Headlin e r: i nterior lighti ng
[!]-Door contact switch. The interior lighting is
controlled automatically.
A switch is no longer needed to switch the read­
ing lights on. A swiping movement or a brief tap
on the light is all that is needed to switch the
light on or off. If you hold your finger on the
reading light when switching it on, this ca n dim
the light down t o a certain level.
Interior light ing
There are other interior lighting functions that
are availab le. Several functions can be set in the
Infotainment system. Select in the Infotainment
system: I MENUl button > Vehicle > left control
b u
tton >Vehicle settings> Interior lighting.