service CHERY TIGGO 2009 Service Repair Manual

Downloaded from www.Manualslib.com manuals search engine 5. Remove the shift cable adjusting bolt (1) from thetransaxle gearshift switch.
6. Remove the gearshift knob (1).
7. Remove the gearshift cover (2) from the lower console.
8. Apply the parking brake (apply parking brake handle to clear lower console during removal).
9. Remove the lower console (See Lower Console Removal & Installation in Section 15 Body & Accessories).
10. Remove the shift cable from the gearshift mechanism.
11. Disconnect the electrical connector (2).
12. Remove the four bolts (1) and then remove the gearshift mechanism from the bracket.
ON-VEHICLE SERVICE
LTSM080167
BESM080049
LTSM080182
08–244Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 13. Installation is in the reverse order of removal.
NOTE :
If the battery has low voltage, press the release switch
(1) to move the gearshift lever.
ON-VEHICLE SERVICE
LTSM080187
08
08–245Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 5-SPEED MANUAL TRANSAXLE
GENERAL INFORMATION08-247
Description 08-247
Operation 08-250
Specifications 08-251
Special Tools 08-253
DIAGNOSIS & TESTING08-259
Abnormal Noise 08-259
Symptom Diagnostics 08-259
ON-VEHICLE SERVICE08-260
Manual Transaxle Assembly 08-260
Removal & Installation 08-260
Gear Selector & Shifter Assembly 08-264
Removal & Installation 08-264
Disassembly 08-267
Assembly 08-268
MANUAL TRANSAXLE UNIT REPAIR08-270
Transaxle 08-270
Specifications 08-270
Disassembly 08-270
Inspection 08-274
Assembly 08-275
Input Shaft 08-278
Specifications 08-278Disassemble
08-279
Assemble 08-281
Inspection 08-285
Output Shaft 08-287
Disassemble 08-287
Assemble 08-290
Output Gear For Reverse Gear 08-296
Disassemble 08-296
Inspection 08-296
5th-Reverse Gear Shift Fork 08-297
Disassemble 08-297
Assemble 08-298
3rd-4th Gear Shift Fork 08-298
Disassemble 08-298
Assemble 08-299
1st-2nd Gear Shift Fork 08-299
Disassemble 08-299
Assembly 08-300
Transaxle Clutch Housing Assembly 08-301
Disassemble 08-301
Assembly 08-303
Transaxle Main Housing Assembly 08-305
Assembly 08-305
08–246Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine ON-VEHICLE SERVICE
Manual Transaxle Assembly
Removal & Installation
NOTE :
The following special tools are required to perform the repair procedure:
•MB-990938 - Handle
• MB-990935 - Installer Connector
1. Raise and support the vehicle.
2. Disconnect the negative battery cable.
3. Remove the battery and battery tray (See Battery Removal & Installation in Section 05 Starting & Charging).
4. Remove air cleaner and air duct.
5. Drain the cooling system (See Cooling System Draining Procedure in Section 06 Cooling System).
6. Remove the base mounting of the air cleaner housing assembly.
7. Remove the backup lamp switch (2) and vehicle speed sensor (1).
LTSM020226
LTSM030029
08–260Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 8. Remove the two shift cables (1) from the transaxle.
9. Remove the shift cable clamp (1) from the shiftcable bracket.
10. Remove the clutch master cylinder outlet pipe (1) from the clutch slave cylinder.
(Tighten: Outlet pipe bolt to 17 ± 1 N·m)
11. Remove the starter motor (See Starter Removal & Installation in Section 05 Starting & Charging).
12. Support the engine using an engine support fixture or suitable jack.
13. Remove the engine to transaxle upper bolts and remove the bracket.
(Tighten: Engine to transaxle upper bolts to 80
N·m)
ON-VEHICLE SERVICE
BESM080051
VISM080026
LTSM080191
08
08–261Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 14. Remove transaxle mount nuts (2) and the transaxlemount bracket bolts (1).
(Tighten: Transaxle mount nuts to 120 N·m)
15. Raise the vehicle.
16. Remove the transaxle drain plug (1) and drain the transaxle fluid.
17. Remove both front axle shafts (See Front Axle Shaft Removal & Installation in Section 09 Driveline & Axle).
18. Remove the engine undercover and splash shields.
19. Remove the front engine mount bolts (1). (Tighten: Front mount bolts to 60 N·m)
ON-VEHICLE SERVICE
LTSM020156
VISM030007
BESM080035
08–262Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 20. Remove the rear engine mount bolts (2) and therear engine mount bracket bolts (1).
(Tighten: Rear mount bolts to 40 N·m)
21. Remove the sub-frame assembly (See Sub-Frame Assembly Removal & Installation in Section 10 Suspension).
22. Remove the engine to transaxle lower bolts (1). (Tighten: Transaxle mount bolts to 40 N·m)
23. Separate the transaxle from the engine and remove it from the vehicle.
WARNING!
Support the transaxle with a suitable jack while removing the transaxle.
24. Installation is in the reverse order of removal.
Installation Notes:
•Refill 2.2L transaxle fluid through the fill hole (1)
until the fluid starts to leak from the fill hole.
• After installation, check for any fluid leakage and
verify the transaxle fluid level is correct.
ON-VEHICLE SERVICE
LTSM020188
VISM080002
LTSM080189
08
08–263Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Gear Selector & Shifter Assembly
Removal & Installation
ON-VEHICLE SERVICE
LTSM08008708–264Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 1. Disconnect the negative battery cable.
2. Remove the air cleaner housing assembly.
3. Remove the two shift cables (1) from the transaxle.
4. Remove the shift cable clamp (1) from the shiftcable bracket.
5. Raise and support the vehicle.
1 - Backup Lamp Switch Assembly
2 - Limit Stop Screw-Interlocking Plate
3 - Plain Washer-Interlocking Plate Limit Stop Screw
4 - Bearing-Gear Shift Mechanism
5 - Lower Lining - Selector Lever
6 - Selector Lever Assembly
7 - Washer
8 - Bolt
9 - Upper Dust Boot - Selector Lever
10 - Nut
11 - Plain Washer-Gear Selecting Arm Nu
12 - Gear Shifting Arm Assembly
13 - Gear Shifting Drive Slider
14 - Dust Cap-Gear Shifting Shaft Fluid Seal
15 - Lower Dust Cap-Gear Selecting Arm
16 - Lower Bushing-Gear Selecting Arm17 - Gear Selecting Arm Assembly
18 - Upper Bushing-Gear Selecting Arm
19 - Baffle-Rear Neutral Position Return Spring
20 - Rear Neutral Retracting Spring
21 - Reverse Gear Lock Assembly
22 - Reverse Gear Lock Assembly Pin
23 - Selector Finger Pin
24 - Selector Finger
25 - Interlock Plate Assembly
26 - Front Neutral Retracting Spring Assembly
27 - Gearshift Shaft
28 - Retainer-Reverse Gear Lock
29 - Gear Shift Mechanism Housing
30 - Air Duct
31 - Air Duct Cap
32 - Bolt
ON-VEHICLE SERVICE
LTSM080087
BESM080051 VISM080026
08
08–265Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 6. Remove the gearshift knob.
7. Remove the gearshift boot from the lower console.
8. Apply the parking brake (apply parking brake han-dle to clear lower console upon removal).
9. Remove the lower console (See Lower Console Removal & Installation in Section 15 Body & Accessories).
10. Remove the clip on the gearshift mechanism and then remove the crossover cable and the selector
cable (1) from the gearshift mechanism.
11. Remove the four bolts (1) and then remove the gearshift mechanism from the bracket.
ON-VEHICLE SERVICE
VISM080017
VISM080018
BESM080054
BESM080053
08–266Chery Automobile Co., Ltd.